Özgür Özgün
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Özgür Özgün has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Ali Ercetin
Department of Naval Architecture and Marine Engineering, Maritime Faculty, Bandırma Onyedi Eylul University, Bandırma, Türkiye
7 shared publications - Kubilay Aslantas
Afyon Kocatepe Universitesi
5 shared publications H. Özkan Gülsoy
4 shared publications- Zulkuf Balalan
Bingöl Üniversitesi
4 shared publications - Fehim Findik
Metallurgy and Materials Engineering Department Faculty of Technology Sakarya Applied Sciences University Sakarya Turkey
3 shared publications Ramazan Yılmaz
Sakarya University, Technology Faculty, Metallurgy and Materials Eng. Dep., 54187 Sakarya, Turkey
2 shared publications
Latest Publications
- Open Access
Interface Engineering in FAST/SPS-Processed Multi-Material Metallic Systems: Bonding Mechanisms, Interfacial Reactions, and Mechanical Integrity
Engineering components often require different properties in different regions, and a single material may not provide all of them. Reliable joining is important for refractory metal–steel, dissimilar superalloy, and Ti/Mg combinations. Field-assisted sintering technology/spark plasma sintering (FAST/SPS) combines pressure with rapid heating for direct joining and fabrication of interlayered and graded metallic structures in short cycles. This review evaluates factors affecting bond formation and mechanical integrity at FAST/SPS-processed metallic interfaces. Sufficient real contact is needed for load transfer but does not alone ensure mechanical integrity. Surface oxides can restrict contact, while local deformation may increase contact area and disrupt oxide films. As contact develops, atomic transport and interfacial reactions may alter transition-region composition and phase morphology, affecting fracture paths. Interlayers may improve contact and limit undesirable reactions but can also create new interfaces and reaction regions. Compositional transitions, reaction regions, and local hardness indicate interface development, but assessing their mechanical significance requires mechanical testing and fracture analysis. Room-temperature performance alone does not define service behavior. Thermal cycling, high heat flux, electrical conditions, or corrosive environments may therefore require application-specific evaluation. Differences in materials, equipment, geometry, and test methods limit direct comparison. Processing windows should therefore be tailored to each material pair and interface architecture according to operating temperature, loading, functional requirements, and environmental exposure.
Open AccessInterface Engineering in FAST/SPS-Processed Multi-Material Metallic Systems: Bonding Mechanisms, Interfacial Reactions, and Mechanical Integrity
Engineering components often require different properties in different regions, and a single material may not provide all of them. Reliable joining is important for refractory metal–steel, dissimilar superalloy, and Ti/Mg combinations. Field-assisted sintering technology/spark plasma sintering (FAST/SPS) combines pressure with rapid heating for direct joining and fabrication of interlayered and graded metallic structures in short cycles. This review evaluates factors affecting bond formation and mechanical integrity at FAST/SPS-processed metallic interfaces. Sufficient real contact is needed for load transfer but does not alone ensure mechanical integrity. Surface oxides can restrict contact, while local deformation may increase contact area and disrupt oxide films. As contact develops, atomic transport and interfacial reactions may alter transition-region composition and phase morphology, affecting fracture paths. Interlayers may improve contact and limit undesirable reactions but can also create new interfaces and reaction regions. Compositional transitions, reaction regions, and local hardness indicate interface development, but assessing their mechanical significance requires mechanical testing and fracture analysis. Room-temperature performance alone does not define service behavior. Thermal cycling, high heat flux, electrical conditions, or corrosive environments may therefore require application-specific evaluation. Differences in materials, equipment, geometry, and test methods limit direct comparison. Processing windows should therefore be tailored to each material pair and interface architecture according to operating temperature, loading, functional requirements, and environmental exposure.
- Open Access
- 30 May 2026
- Published by Springer Nature in Archives of Computational Methods in Engineering
- Vol. 33 (8) , 11511-11538
AI-Driven Image Processing for Microstructure and Surface Characterization: A Systematic Review of Methods, Materials, and Applications
- 30 May 2026
- Published by Springer Nature in Archives of Computational Methods in Engineering
- Vol. 33 (8) , 11511-11538
Open AccessAI-Driven Image Processing for Microstructure and Surface Characterization: A Systematic Review of Methods, Materials, and Applications
- 1 January 2025
- Published by Firat Universitesi in Turkish Journal of Science and Technology
- Vol. 20 (2) , 495-505
Characteristics of AISi10Mg Aluminum Alloy Plates Produced Through Additive Manufacturing Technique
TThe microstructure and mechanical properties of AlSi10Mg aluminum alloy sheets produced by additive manufacturing method were revealed. It was clearly observed that the microstructure consisted of weld pools separated by boundaries. Furthermore, a small number of distributed pores with diameters ranging from 35 µm to 5 µm were detected in the microstructure. A few small-sized pores are a sign of good production. Vickers microhardness of the produced AlSi10Mg alloy was measured to be average 126.625 HV. Additionally, its tensile strength and three-point bending strength value were found to be 433 MPa and 548 MPa, respectively. The tensile fracture surface had many small and deep dimples while three-point bending fracture surface also possessed dimples, however, bigger and shallower compared with that of tensile fracture. Therefore, the tensile and three-point bending tests showed a reasonable ductile fracture behavior.
- 1 January 2025
- Published by Firat Universitesi in Turkish Journal of Science and Technology
- Vol. 20 (2) , 495-505
Characteristics of AISi10Mg Aluminum Alloy Plates Produced Through Additive Manufacturing Technique
TThe microstructure and mechanical properties of AlSi10Mg aluminum alloy sheets produced by additive manufacturing method were revealed. It was clearly observed that the microstructure consisted of weld pools separated by boundaries. Furthermore, a small number of distributed pores with diameters ranging from 35 µm to 5 µm were detected in the microstructure. A few small-sized pores are a sign of good production. Vickers microhardness of the produced AlSi10Mg alloy was measured to be average 126.625 HV. Additionally, its tensile strength and three-point bending strength value were found to be 433 MPa and 548 MPa, respectively. The tensile fracture surface had many small and deep dimples while three-point bending fracture surface also possessed dimples, however, bigger and shallower compared with that of tensile fracture. Therefore, the tensile and three-point bending tests showed a reasonable ductile fracture behavior.
- 8 November 2024
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 121 (6) , 612
Influence of Mo addition on microstructural and mechanical characteristics of TiXMo5Cu alloys manufactured by powder metallurgy
In the present study, TiXMo5Cu alloys were produced utilizing the powder metallurgy technique. Alloy samples with different ratios of Mo added were shaped by uniaxial pressing under 550 MPa pressure. The shaped samples were subjected to a sintering process at 5 different temperatures for a waiting time of 180 min in a 99.99% pure argon gas atmosphere. The densities of the fabricated specimens were found with the Archimedes principle. Microstructures of the obtained samples were attained by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) examinations. For the determination of the mechanical characteristics, micro hardness and tensile tests were applied. According to the density measurements, the highest relative density values were attained with the sintering temperature of 1300 °C, and a higher Mo ratio resulted in a lower relative density. The microstructure of the fabricated specimens is comprised of α-Ti and β-Ti phases. The α-Ti phase ratio in the microstructure reduced based on rising Mo, while the ratio of the β-Ti phase increased. Accordingly, while the hardness values increased, the strength values decreased.
- 8 November 2024
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 121 (6) , 612
Influence of Mo addition on microstructural and mechanical characteristics of TiXMo5Cu alloys manufactured by powder metallurgy
In the present study, TiXMo5Cu alloys were produced utilizing the powder metallurgy technique. Alloy samples with different ratios of Mo added were shaped by uniaxial pressing under 550 MPa pressure. The shaped samples were subjected to a sintering process at 5 different temperatures for a waiting time of 180 min in a 99.99% pure argon gas atmosphere. The densities of the fabricated specimens were found with the Archimedes principle. Microstructures of the obtained samples were attained by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) examinations. For the determination of the mechanical characteristics, micro hardness and tensile tests were applied. According to the density measurements, the highest relative density values were attained with the sintering temperature of 1300 °C, and a higher Mo ratio resulted in a lower relative density. The microstructure of the fabricated specimens is comprised of α-Ti and β-Ti phases. The α-Ti phase ratio in the microstructure reduced based on rising Mo, while the ratio of the β-Ti phase increased. Accordingly, while the hardness values increased, the strength values decreased.
- Open Access
- 26 March 2024
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 13 (1) , 118-122
Ergonomics in Beekeeping Activities
Most of the academic research that has been done on beekeeping focuses on bee health, ways to protect bees from diseases, and how to get more yield. However, there are also ergonomic risks during beekeeping activities that affect the health of beekeepers and indirectly affect productivity. In this study, ergonomic risks that threaten the health of beekeepers were investigated. The most important ergonomic risks for beekeepers are those that threaten the health of the musculoskeletal system. These risks arise from working with improper body posture for long periods of time, manual handling/lifting, and the use of non-ergonomic hand tools. Measures and solutions that can be applied to protect the health of beekeepers against ergonomic risks and to increase working efficiency are presented.
- 26 March 2024
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 13 (1) , 118-122
Open AccessErgonomics in Beekeeping Activities
Most of the academic research that has been done on beekeeping focuses on bee health, ways to protect bees from diseases, and how to get more yield. However, there are also ergonomic risks during beekeeping activities that affect the health of beekeepers and indirectly affect productivity. In this study, ergonomic risks that threaten the health of beekeepers were investigated. The most important ergonomic risks for beekeepers are those that threaten the health of the musculoskeletal system. These risks arise from working with improper body posture for long periods of time, manual handling/lifting, and the use of non-ergonomic hand tools. Measures and solutions that can be applied to protect the health of beekeepers against ergonomic risks and to increase working efficiency are presented.
- Open Access
- 12 August 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (8) , 1590
Optimization of Machining Parameters to Minimize Cutting Forces and Surface Roughness in Micro-Milling of Mg13Sn Alloy
This comprehensive study investigates the micro-milling of a Mg13Sn alloy, a material of considerable interest in various high-precision applications, such as biomedical implants. The main objective of the study was to explore the optimizations of variable feed per tooth (fz), cutting speed (Vc), and depth of cut (ap) parameters on the key outcomes of the micro-milling process. A unique experimental setup was employed, employing a spindle capable of achieving up to 60,000 revolutions per minute. Additionally, the study leveraged linear slides backed by micro-step motors to facilitate precise axis movements, thereby maintaining a resolution accuracy of 0.1 μm. Cutting forces were accurately captured by a mini dynamometer and subsequently evaluated based on the peak to valley values for Fx (tangential force) and Fy (feed force). The study results revealed a clear and complex interplay between the varied cutting parameters and their subsequent impacts on the cutting forces and surface roughness. An increase in feed rate and depth of cut significantly increased the cutting forces. However, the cutting forces were found to decrease noticeably with the elevation of cutting speed. Intriguingly, the tangential force (Fx) was consistently higher than the feed force (Fy). Simultaneously, the study determined that the surface roughness, denoted by Sa values, increased in direct proportion to the feed rate. It was also found that the Sa surface roughness values decreased with the increase in cutting speed. This study recommends a parameter combination of fz = 5 µm/tooth feed rate, Vc = 62.8 m/min cutting speed, and ap = 400 µm depth of cut to maintain a Sa surface roughness value of less than 1 µm while ensuring an optimal material removal rate and machining time. The results derived from this study offer vital insights into the micro-milling of Mg13Sn alloys and contribute to the current body of knowledge on the topic.
- 12 August 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (8) , 1590
Open AccessOptimization of Machining Parameters to Minimize Cutting Forces and Surface Roughness in Micro-Milling of Mg13Sn Alloy
This comprehensive study investigates the micro-milling of a Mg13Sn alloy, a material of considerable interest in various high-precision applications, such as biomedical implants. The main objective of the study was to explore the optimizations of variable feed per tooth (fz), cutting speed (Vc), and depth of cut (ap) parameters on the key outcomes of the micro-milling process. A unique experimental setup was employed, employing a spindle capable of achieving up to 60,000 revolutions per minute. Additionally, the study leveraged linear slides backed by micro-step motors to facilitate precise axis movements, thereby maintaining a resolution accuracy of 0.1 μm. Cutting forces were accurately captured by a mini dynamometer and subsequently evaluated based on the peak to valley values for Fx (tangential force) and Fy (feed force). The study results revealed a clear and complex interplay between the varied cutting parameters and their subsequent impacts on the cutting forces and surface roughness. An increase in feed rate and depth of cut significantly increased the cutting forces. However, the cutting forces were found to decrease noticeably with the elevation of cutting speed. Intriguingly, the tangential force (Fx) was consistently higher than the feed force (Fy). Simultaneously, the study determined that the surface roughness, denoted by Sa values, increased in direct proportion to the feed rate. It was also found that the Sa surface roughness values decreased with the increase in cutting speed. This study recommends a parameter combination of fz = 5 µm/tooth feed rate, Vc = 62.8 m/min cutting speed, and ap = 400 µm depth of cut to maintain a Sa surface roughness value of less than 1 µm while ensuring an optimal material removal rate and machining time. The results derived from this study offer vital insights into the micro-milling of Mg13Sn alloys and contribute to the current body of knowledge on the topic.
- 12 July 2023
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 120 (4) , 411
Effect of Mo ratio on the microstructure and mechanical properties of TiMoNi alloys fabricated by powder metallurgy method
TiNi alloys have good biocompatibility and are widely used as biomaterials in the human body. Mo is a nontoxic element and increases biocompatibility as well as corrosion resistance. Ti-Mo-Ni-based alloys utilized in biomedical applications should have high strength. In this context, the microstructure and mechanical properties of TixMo6Ni alloys produced by the powder metallurgy method were investigated in this study. Five different Ti alloys were obtained by adding a fixed amount of (6%) Ni and different ratios (1, 3, 5, 8, 10%) Mo into the Ti powder. Alloy powders were sintered at different temperatures after pressing with a constant pressure of 520 MPa. In general, the highest density values were reached at 1250 °C. Microstructure examinations were performed by scanning electron microscopy (SEM), energy distribution spectrometry (EDS) and X-ray diffraction analysis (XRD) analyses. In the microstructure, it was observed that the grain size and pores increased as the Mo ratio increased. The hardness values increased with the increase of the Mo ratio. However, the relative density values decreased with increasing Mo ratio.
- 12 July 2023
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 120 (4) , 411
Effect of Mo ratio on the microstructure and mechanical properties of TiMoNi alloys fabricated by powder metallurgy method
TiNi alloys have good biocompatibility and are widely used as biomaterials in the human body. Mo is a nontoxic element and increases biocompatibility as well as corrosion resistance. Ti-Mo-Ni-based alloys utilized in biomedical applications should have high strength. In this context, the microstructure and mechanical properties of TixMo6Ni alloys produced by the powder metallurgy method were investigated in this study. Five different Ti alloys were obtained by adding a fixed amount of (6%) Ni and different ratios (1, 3, 5, 8, 10%) Mo into the Ti powder. Alloy powders were sintered at different temperatures after pressing with a constant pressure of 520 MPa. In general, the highest density values were reached at 1250 °C. Microstructure examinations were performed by scanning electron microscopy (SEM), energy distribution spectrometry (EDS) and X-ray diffraction analysis (XRD) analyses. In the microstructure, it was observed that the grain size and pores increased as the Mo ratio increased. The hardness values increased with the increase of the Mo ratio. However, the relative density values decreased with increasing Mo ratio.
- Open Access
Microstructural and Mechanical Behavior Investigations of Nb-Reinforced Mg–Sn–Al–Zn–Mn Matrix Magnesium Composites
This research focuses on the fabrication and characterization of TAZ532-xNb composites, employing high-purity, micron-sized powders of Mg, Sn, Al, Zn, Mn, and Nb as the raw materials. These powders were subjected to a paraffin coating process aimed at mitigating oxidation. The formation of composites was achieved via hot pressing and was followed by surface preparation and analysis using scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). An X-ray diffraction (XRD) study was conducted to identify the microstructural phases. Quantitative assessments including the theoretical density, actual density, and relative density were computed, and their fluctuations in relation to the increasing Nb reinforcement ratio were scrutinized. Furthermore, the mechanical attributes of the composites, such as hardness and tensile strength, were assessed via experimental procedures. The absence of oxygen-related peaks in the XRD patterns endorsed the successful execution of the paraffin coating technique and protective gas atmosphere during sintering. The detection of α-Mg, Mg2Sn, MgZn, Mg17Al12, and Nb phases within the Nb-reinforced composite patterns authenticated the formation of the intended phases. Notably, the relative density values of the composites surpassed 95%, indicating efficient sintering. SEM results disclosed a densely packed microstructure, with Nb reinforcement particles evenly distributed along the grain boundaries, devoid of particle clustering or significant grain growth. These composites manifested exceptional wetting characteristics, which can be attributed to the employment of Mg alloy as the matrix material. EDS data confirmed the proportions of Nb within the composites, aligning with the quantities incorporated during fabrication. The composites showcased an increase in microhardness values with the escalating Nb reinforcement ratio, credited to the harder constitution of Nb particles in comparison to the matrix alloy. Concurrently, tensile strength showed a significant improvement with the increment in Nb reinforcement, while elongation values peaked at a specific Nb reinforcement level. The positive evolution of tensile strength properties was ascribed to the escalated Nb reinforcement ratio, grain size, and consequent higher sample densities.
Open AccessMicrostructural and Mechanical Behavior Investigations of Nb-Reinforced Mg–Sn–Al–Zn–Mn Matrix Magnesium Composites
This research focuses on the fabrication and characterization of TAZ532-xNb composites, employing high-purity, micron-sized powders of Mg, Sn, Al, Zn, Mn, and Nb as the raw materials. These powders were subjected to a paraffin coating process aimed at mitigating oxidation. The formation of composites was achieved via hot pressing and was followed by surface preparation and analysis using scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). An X-ray diffraction (XRD) study was conducted to identify the microstructural phases. Quantitative assessments including the theoretical density, actual density, and relative density were computed, and their fluctuations in relation to the increasing Nb reinforcement ratio were scrutinized. Furthermore, the mechanical attributes of the composites, such as hardness and tensile strength, were assessed via experimental procedures. The absence of oxygen-related peaks in the XRD patterns endorsed the successful execution of the paraffin coating technique and protective gas atmosphere during sintering. The detection of α-Mg, Mg2Sn, MgZn, Mg17Al12, and Nb phases within the Nb-reinforced composite patterns authenticated the formation of the intended phases. Notably, the relative density values of the composites surpassed 95%, indicating efficient sintering. SEM results disclosed a densely packed microstructure, with Nb reinforcement particles evenly distributed along the grain boundaries, devoid of particle clustering or significant grain growth. These composites manifested exceptional wetting characteristics, which can be attributed to the employment of Mg alloy as the matrix material. EDS data confirmed the proportions of Nb within the composites, aligning with the quantities incorporated during fabrication. The composites showcased an increase in microhardness values with the escalating Nb reinforcement ratio, credited to the harder constitution of Nb particles in comparison to the matrix alloy. Concurrently, tensile strength showed a significant improvement with the increment in Nb reinforcement, while elongation values peaked at a specific Nb reinforcement level. The positive evolution of tensile strength properties was ascribed to the escalated Nb reinforcement ratio, grain size, and consequent higher sample densities.
- Open Access
- 7 October 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (2) , 1003-1012
Toz metal Al2O3 takviyeli Mg5Sn matrisli kompozitler: Üretim ve karakterizasyon
Bu çalışmada, ağırlıkça %5 Sn içeren Mg-Sn matris içerisine farklı oranlarda Al2O3 ilave edilerek toz metalurjisi (TM) yöntemiyle Mg5Sn-xAl2O3 kompozit malzemeler üretilmiştir. Üretimde Mg tozlarının sahip olduğu yüksek reaktivitenin yol açacağı olumsuzlukları önlemek amacıyla yeni bir karıştırma tekniği kullanılmıştır. Hazırlanan toz karışımlarından numune üretimi sıcak presleme tekniği ile gerçekleştirilmiştir. Üretilen numuneler, yoğunluk ölçümleri, mikroyapı incelemeleri ve mekanik testler ile karakterize edilmiştir. Ölçülen yoğunluk değerleri teorik yoğunluğa oldukça yakın elde edilmiştir. Mikroyapı incelemeleri, alümina takviyesinin mikroyapıda homojen bir şekilde dağıldığını göstermiştir. Artan Al2O3 takviye oranı, sertlik ve çekme dayanımı değerlerinde önemli artışlar sağlamıştır.
- 7 October 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (2) , 1003-1012
Open AccessToz metal Al2O3 takviyeli Mg5Sn matrisli kompozitler: Üretim ve karakterizasyon
Bu çalışmada, ağırlıkça %5 Sn içeren Mg-Sn matris içerisine farklı oranlarda Al2O3 ilave edilerek toz metalurjisi (TM) yöntemiyle Mg5Sn-xAl2O3 kompozit malzemeler üretilmiştir. Üretimde Mg tozlarının sahip olduğu yüksek reaktivitenin yol açacağı olumsuzlukları önlemek amacıyla yeni bir karıştırma tekniği kullanılmıştır. Hazırlanan toz karışımlarından numune üretimi sıcak presleme tekniği ile gerçekleştirilmiştir. Üretilen numuneler, yoğunluk ölçümleri, mikroyapı incelemeleri ve mekanik testler ile karakterize edilmiştir. Ölçülen yoğunluk değerleri teorik yoğunluğa oldukça yakın elde edilmiştir. Mikroyapı incelemeleri, alümina takviyesinin mikroyapıda homojen bir şekilde dağıldığını göstermiştir. Artan Al2O3 takviye oranı, sertlik ve çekme dayanımı değerlerinde önemli artışlar sağlamıştır.