ZBZulkuf Balalan

Zulkuf Balalan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zulkuf Balalan has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Characteristics of AISi10Mg Aluminum Alloy Plates Produced Through Additive Manufacturing Technique

    by Mehmet Yaz, Ömer Ekinci, Zülküf Balalan, Özgür Özgün

    TThe microstructure and mechanical properties of AlSi10Mg aluminum alloy sheets produced by additive manufacturing method were revealed. It was clearly observed that the microstructure consisted of weld pools separated by boundaries. Furthermore, a small number of distributed pores with diameters ranging from 35 µm to 5 µm were detected in the microstructure. A few small-sized pores are a sign of good production. Vickers microhardness of the produced AlSi10Mg alloy was measured to be average 126.625 HV. Additionally, its tensile strength and three-point bending strength value were found to be 433 MPa and 548 MPa, respectively. The tensile fracture surface had many small and deep dimples while three-point bending fracture surface also possessed dimples, however, bigger and shallower compared with that of tensile fracture. Therefore, the tensile and three-point bending tests showed a reasonable ductile fracture behavior.

  • Microstructure and mechanical properties of friction welded dissimilar AISI 1040 and AISI 304 steels

    by Zulkuf Balalan, Mehmet Yaz, Omer Ekinci, Sedat Buldag

    The development of technology and the increase in needs have affected the manufacturing methods. It is of great importance to combine different materials to reduce costs and increase performance and design flexibility. Different parts can be joined by friction welding, which is a solid-state welding method. In this study, the weldability of AISI 304 stainless steel and AISI 1040 carbon steel with friction welding has been investigated. During welding, the temperature changes of the welds were measured. In addition to SEM, XRD, and EDS tests to examine the microstructure of the welds, tensile strength tests and hardness measurements were also performed to find out their mechanical characteristics. According to the analysis and test results, the best welding parameters were observed in the weld sample S6. As a result of this experimental study, it was seen that these different steels can be joined by friction welding.

  • Influence of Mo addition on microstructural and mechanical characteristics of TiXMo5Cu alloys manufactured by powder metallurgy

    by Murat Kurt, Ozgur Ozgun, Omer Ekinci, Zulkuf Balalan

    In the present study, TiXMo5Cu alloys were produced utilizing the powder metallurgy technique. Alloy samples with different ratios of Mo added were shaped by uniaxial pressing under 550 MPa pressure. The shaped samples were subjected to a sintering process at 5 different temperatures for a waiting time of 180 min in a 99.99% pure argon gas atmosphere. The densities of the fabricated specimens were found with the Archimedes principle. Microstructures of the obtained samples were attained by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) examinations. For the determination of the mechanical characteristics, micro hardness and tensile tests were applied. According to the density measurements, the highest relative density values were attained with the sintering temperature of 1300 °C, and a higher Mo ratio resulted in a lower relative density. The microstructure of the fabricated specimens is comprised of α-Ti and β-Ti phases. The α-Ti phase ratio in the microstructure reduced based on rising Mo, while the ratio of the β-Ti phase increased. Accordingly, while the hardness values increased, the strength values decreased.

  • Open Access

    Investigation of Friction Welding Dissimilar AISI 304 and AISI 1040 Steels

    by Zülküf Balalan, Mehmet Yaz, Sedat Buldağ

    The temperature at the weld region increased in parallel with the friction time. Increasing the friction time ensured the formation of a stronger weld. The highest tensile stress and elongation value were seen in the S3 weld sample, which had the highest friction time. The lowest tensile stress and elongation values were determined in the S1 weld sample with the lowest friction time. S2 and S3 weld samples were broken as ductile during the tensile test, while S1 weld sample was broken as a mixture of brittle and ductile. The hardness value at the weld interface decreased with an increase in the friction time. It has been observed that the width and shape of the excessively deformed region on both sides of the joint interface changed depending on the friction time.


  • Effect of Mo ratio on the microstructure and mechanical properties of TiMoNi alloys fabricated by powder metallurgy method

    by Sabri Bulbul, Zulkuf Balalan, Ozgur Ozgun, Omer Ekinci

    TiNi alloys have good biocompatibility and are widely used as biomaterials in the human body. Mo is a nontoxic element and increases biocompatibility as well as corrosion resistance. Ti-Mo-Ni-based alloys utilized in biomedical applications should have high strength. In this context, the microstructure and mechanical properties of TixMo6Ni alloys produced by the powder metallurgy method were investigated in this study. Five different Ti alloys were obtained by adding a fixed amount of (6%) Ni and different ratios (1, 3, 5, 8, 10%) Mo into the Ti powder. Alloy powders were sintered at different temperatures after pressing with a constant pressure of 520 MPa. In general, the highest density values were reached at 1250 °C. Microstructure examinations were performed by scanning electron microscopy (SEM), energy distribution spectrometry (EDS) and X-ray diffraction analysis (XRD) analyses. In the microstructure, it was observed that the grain size and pores increased as the Mo ratio increased. The hardness values increased with the increase of the Mo ratio. However, the relative density values decreased with increasing Mo ratio.


  • Influence of tool pin shape and rotation speed for friction stir spot welding of AZ91 magnesium alloy sheets

    by Omer Ekinci, Zulkuf Balalan

    Light weight design is believed one of the most effective ways to enhance performance, reduce fuel consumption and harmful gases for air and land vehicles. Hence, welding lightweight metals like magnesium alloys is very important. Friction stir spot welding joints of 2 mm thick AZ91 magnesium alloy sheets by overlapping two of them were performed utilizing two welding tools having conical and triangular pin at 800, 1200 and 1600 revolution per minute (rpm) tool rotational velocities for each tool to identify the pin shape and rotation speed impact on microstructure and mechanical features of the created joints. The stir zones of the joints contained smaller grains, therefore had higher hardness in comparison to AZ91 base metal, thermo-mechanically affected zone (TMAZ) and heat affected zone (HAZ). The lowest hardness values were found in HAZ of the welds. Hardness fell slightly with a rise in rotation speed for both tools because of more heat input. Strength of the joints manufactured applying the triangular pin tool was better because this pin mixed materials better, thus created joints with bigger welding area and greater hardness. The strongest weld was fabricated by applying triangular pin tool and 1600 rpm.


  • Effect of tool pin geometry on microstructure and mechanical properties of friction stir spot welds of 7075-T651 aluminium alloy

    by Omer Ekinci, Zulkuf Balalan

    7075-T651 aluminium alloy sheets were overlapped and friction stir spot welded using two welding tools having different pin geometries (one with a conical pin and other with a triangular pin) and 800, 1200 and 1600 revolution per minute (rpm) tool rotation speeds at a constant tool plunge and removal speed of 7.3 mm/min, tool plunge depth of 3.8 mm and tool dwell time of 5 s. Microstructure, Vickers microhardness, tensile shear strength, fracture surface after tensile shear test and impact energy of the produced friction stir spot welds were examined. As a result, the welds made via triangular pin tool had considerably higher tensile shear loads than the welds made via conical pin tool since the weld bond widths (stir zones) of the welds made via triangular pin tool were larger. The strongest welds made at 1200 rpm for conical pin tool and triangular pin tool. The tensile shear loads of the welds increased significantly when tool rotation speed increased from 800 to 1200 rpm for both welding tools and then decreased slightly for triangular pin tool and dramatically for conical pin tool with further increasing tool rotation speed from 1200 to 1600 rpm. Maximum tensile shear load of 7.776 kN and impact energy of 16 J obtained in the weld made at 1200 rpm using triangular pin tool. The welds made at 800 rpm had lowest impact energy. The lowest hardness values found in the heat affected zones of the welds. Circumferential fracture mode for conical pin tool welds and nugget pull-out fracture mode for triangular pin tool welds observed after tensile tests.


  • Microstructure and mechanical properties of Cu‐B 4 C and CuAl‐B 4 C composites produced by hot pressing

    by Zulkuf Balalan, Furkan Gulan

    Cu matrix composite materials reinforced with B 4 C particle at four different contents (1.5 wt%, 3.0 wt%, 4.5 wt% and 6.0 wt%) and also CuAl matrix composites with 13 wt% Al reinforced with B 4 C particle at four different contents (1.5 wt%, 3.0 wt%, 4.5 wt% and 6.0 wt%) were fabricated by hot pressing (HP) and a powder metallurgy (PM) process. Experimental samples were produced by keeping them at 880 °C at the constant pressure of 2.3 × 10 8 Pa for 6 min. The density, microstructure and mechanical properties of the produced samples were examined. The microstructure and phase examinations were carried out by scanning electron microscope (SEM) and optical microscope (OM), energy‐dispersive spectrometer (EDS) and X‐ray diffractometer (XRD) analysis. The hardness measurements, three‐point bending test and impact test were conducted to determine the mechanical properties. As a result of the examinations, it was observed that the relative density values decreased with the increasing content of B 4 C and provided a relatively effective bonding. Moreover, it was homogeneously distributed in the produced specimens. Consequently, there was a considerable increase in the hardness and the bending strength of CuAl matrix specimens with Al addition.