Tatsuya Fukuda
Research Subjects
Tatsuya Fukuda has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Tatsuhiko Aizawa
Surface Engineering Design Laboratory, Shibaura Institute of Technology, Tokyo 144-0056, Japan
6 shared publications - Tomoaki Yoshino
Komatsu-Seiki Kosakusho, Co., Ltd., Suwa 392-0012, Japan
2 shared publications - Tomomi Shiratori
University of Toyama
2 shared publications - Ko-Ichi Ito
Tokai Engineering Service, Co., Ltd., Gifu 504-0852, Japan
1 shared publication
Latest Publications
- Open Access
- 26 January 2026
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 12 (1) , 46
Nitrogen Doping into Thin and Thick Coatings for Nano-structuring and Nano-texturing by Plasma Immersion Nitriding
- 26 January 2026
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 12 (1) , 46
Open AccessNitrogen Doping into Thin and Thick Coatings for Nano-structuring and Nano-texturing by Plasma Immersion Nitriding
- Open Access
Dry Cold Forging of High Strength AISI316 Wires by Massively Nitrogen Supersaturated CoCrMo Dies
The plasma immersion nitriding system was utilized to make massive nitrogen supersaturation (MNS) to CoCrMo disc and die substrates at 723 K for 21.6 ks. The top layer thickness in the multi-layered MNSed layer was 20 μm. Its nitrogen solute content reached 5 mass% on average after SEM-EDX analysis. The surface hardness was 1300 HV1N (HV0.1), which was much higher than the bare CoCrMo with 450 HV1N. The original polycrystalline structure was modified to be a multi-layered microstructure, which consisted of the nanograined MNSed top layer, the buffer layer with a thickness of 5 μm, and the column–granular structured layer with their textured crystallographic orientations. The BOD (ball-on-disc) testing was employed to describe the frictional sliding behavior under the applied loads of 5 N and 10 N and the sliding velocity of 0.1 m/s against the AISI316 ball. The friction coefficient was held constant by 0.68 on average. The CNC (Computer Numerical Control) stamping system was employed to upset the fine-grained 1.0 mm thick AISI316 wire up to 70% in reduction in thickness. The friction coefficient at RT was estimated to be 0.05. A round, fine-grained AISI316 wire was shaped into a thin plate with a thickness of 0.3 mm in cold and dry.
Open AccessDry Cold Forging of High Strength AISI316 Wires by Massively Nitrogen Supersaturated CoCrMo Dies
The plasma immersion nitriding system was utilized to make massive nitrogen supersaturation (MNS) to CoCrMo disc and die substrates at 723 K for 21.6 ks. The top layer thickness in the multi-layered MNSed layer was 20 μm. Its nitrogen solute content reached 5 mass% on average after SEM-EDX analysis. The surface hardness was 1300 HV1N (HV0.1), which was much higher than the bare CoCrMo with 450 HV1N. The original polycrystalline structure was modified to be a multi-layered microstructure, which consisted of the nanograined MNSed top layer, the buffer layer with a thickness of 5 μm, and the column–granular structured layer with their textured crystallographic orientations. The BOD (ball-on-disc) testing was employed to describe the frictional sliding behavior under the applied loads of 5 N and 10 N and the sliding velocity of 0.1 m/s against the AISI316 ball. The friction coefficient was held constant by 0.68 on average. The CNC (Computer Numerical Control) stamping system was employed to upset the fine-grained 1.0 mm thick AISI316 wire up to 70% in reduction in thickness. The friction coefficient at RT was estimated to be 0.05. A round, fine-grained AISI316 wire was shaped into a thin plate with a thickness of 0.3 mm in cold and dry.
- Open Access
- 1 September 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (9) , 309
Galling-Free Forging of Titanium Using Carbon-Supersaturated SiC Coating Dies
The thermal chemical vapor deposition (CVD) process was utilized to fabricate 6H-structured SiC coating dies with carbon control. The carbon-rich clusters along the SiC grain boundaries acted as a pinning site to suppress irregular crystal growth and to homogenize the fine-grained structure. These massive carbon-supersaturated (MCSed) SiC dies with a thickness of 4 mm were utilized for upsetting pure titanium bars in dry and cold conditions. Under a stress gradient from the contact interface to the depth of the SiC coating, the carbon solute isolated from these carbon clusters diffused through the grain boundaries and formed free carbon agglomerates on the contact interface to the pure titanium bars. These in situ-formed free carbon agglomerates acted as a solid lubricant to sustain the friction coefficient at 0.09 at the hot spots on the contact interface and to protect the dies and bars from severe adhesive wearing.
- 1 September 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (9) , 309
Open AccessGalling-Free Forging of Titanium Using Carbon-Supersaturated SiC Coating Dies
The thermal chemical vapor deposition (CVD) process was utilized to fabricate 6H-structured SiC coating dies with carbon control. The carbon-rich clusters along the SiC grain boundaries acted as a pinning site to suppress irregular crystal growth and to homogenize the fine-grained structure. These massive carbon-supersaturated (MCSed) SiC dies with a thickness of 4 mm were utilized for upsetting pure titanium bars in dry and cold conditions. Under a stress gradient from the contact interface to the depth of the SiC coating, the carbon solute isolated from these carbon clusters diffused through the grain boundaries and formed free carbon agglomerates on the contact interface to the pure titanium bars. These in situ-formed free carbon agglomerates acted as a solid lubricant to sustain the friction coefficient at 0.09 at the hot spots on the contact interface and to protect the dies and bars from severe adhesive wearing.
- Open Access
Dry Cold Forging of Pure Titanium Wire to Thin Plate with Use of β-SiC Coating Dies
Dense β-SiC coating with 3C-structure was utilized as a dry cold forging punch and core-die. Pure titanium T328H wires of industrial grade II were employed as a work material. No adhesion or galling of metallic titanium was detected on the contact interface between this β-SiC die and titanium work, even after this continuous forging process, up to a reduction in thickness by 70%. SEM (Scanning Electron Microscopy) and EDX (Electron Dispersive X-ray spectroscopy) were utilized to analyze this contact interface. A very thin titanium oxide layer was in situ formed in the radial direction from the center of the contact interface. Isolated carbon from β-SiC agglomerated and distributed in dots at the center of the initial contact interface. Raman spectroscopy was utilized, yielding the discovery that this carbon is unbound as a free carbon or not bound in SiC or TiC and that intermediate titanium oxides are formed with TiO2 as a tribofilm.
Open AccessDry Cold Forging of Pure Titanium Wire to Thin Plate with Use of β-SiC Coating Dies
Dense β-SiC coating with 3C-structure was utilized as a dry cold forging punch and core-die. Pure titanium T328H wires of industrial grade II were employed as a work material. No adhesion or galling of metallic titanium was detected on the contact interface between this β-SiC die and titanium work, even after this continuous forging process, up to a reduction in thickness by 70%. SEM (Scanning Electron Microscopy) and EDX (Electron Dispersive X-ray spectroscopy) were utilized to analyze this contact interface. A very thin titanium oxide layer was in situ formed in the radial direction from the center of the contact interface. Isolated carbon from β-SiC agglomerated and distributed in dots at the center of the initial contact interface. Raman spectroscopy was utilized, yielding the discovery that this carbon is unbound as a free carbon or not bound in SiC or TiC and that intermediate titanium oxides are formed with TiO2 as a tribofilm.
- Open Access
Thick β-SiC CVD-Coated SiC Die System for Dry Cold Forging of Metals
A thick β-SiC CVD (chemical vapor deposition)-coated SiC device was developed as a new punch and die system for dry, cold forging of pure titanium and austenitic stainless-steel works. This β-SiC coating thickness was 4 mm, enough to make mechanical machining of a cavity into β-SiC coating core die. These β-SiC-coated punch and core dies were fixed into the cassette die for dry, cold forging experiments. The stainless steel and titanium wires with diameters of 1.0 mm were employed as the work material. Different from the conventional metallic and ceramic die systems suffering from work material transfer, this system sustained the galling-free cold, dry forging behavior up to a higher reduction of thickness than 30%. The power to stroke the relationship was in situ monitored to describe this forging behavior up to the specified reduction of the wires together with observations on the geometric change from a circular wire to a pentagonal prism bar. Precise scanning electron microscopy-electron-dispersive X-ray spectroscopy (SEM-EDX) analyses were performed to describe the material compatibility on the contact interface between β-SiC coating and elastoplastically deforming works.
Open AccessThick β-SiC CVD-Coated SiC Die System for Dry Cold Forging of Metals
A thick β-SiC CVD (chemical vapor deposition)-coated SiC device was developed as a new punch and die system for dry, cold forging of pure titanium and austenitic stainless-steel works. This β-SiC coating thickness was 4 mm, enough to make mechanical machining of a cavity into β-SiC coating core die. These β-SiC-coated punch and core dies were fixed into the cassette die for dry, cold forging experiments. The stainless steel and titanium wires with diameters of 1.0 mm were employed as the work material. Different from the conventional metallic and ceramic die systems suffering from work material transfer, this system sustained the galling-free cold, dry forging behavior up to a higher reduction of thickness than 30%. The power to stroke the relationship was in situ monitored to describe this forging behavior up to the specified reduction of the wires together with observations on the geometric change from a circular wire to a pentagonal prism bar. Precise scanning electron microscopy-electron-dispersive X-ray spectroscopy (SEM-EDX) analyses were performed to describe the material compatibility on the contact interface between β-SiC coating and elastoplastically deforming works.
- 15 December 2015
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 4 (1) , 014502
Pulsewise-Motion Controlled Stamping for Microtexturing Onto Aluminum Sheet
High density oxygen plasma-etching was applied to microtexturing onto the diamondlike carbon (DLC) films coated on the die-unit substrates. This mold-die unit with microtextured DLC coating was fixed into a cassette die for computer numerical control (CNC) stamping with the use of precise control both in loading and feeding the sheet materials. In particular, the pulsewise-motion control in stamping was employed to describe the effect of loading and unloading subsequences in the incremental motion on the microtexturing with reference to the normal loading motion. The macroscopic plastic deformation as well as the microscopic metal flow were studied to prove that the pulsewise-motion should be responsible for homogeneous duplication of microcavity patterns into a pure aluminum sheet with high aspect ratio.
- 15 December 2015
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 4 (1) , 014502
Pulsewise-Motion Controlled Stamping for Microtexturing Onto Aluminum Sheet
High density oxygen plasma-etching was applied to microtexturing onto the diamondlike carbon (DLC) films coated on the die-unit substrates. This mold-die unit with microtextured DLC coating was fixed into a cassette die for computer numerical control (CNC) stamping with the use of precise control both in loading and feeding the sheet materials. In particular, the pulsewise-motion control in stamping was employed to describe the effect of loading and unloading subsequences in the incremental motion on the microtexturing with reference to the normal loading motion. The macroscopic plastic deformation as well as the microscopic metal flow were studied to prove that the pulsewise-motion should be responsible for homogeneous duplication of microcavity patterns into a pure aluminum sheet with high aspect ratio.