RCRong-Yeu Chang

Rong-Yeu Chang

*This is an algorithmically generated author record based on publicly available information.

Rong-Yeu Chang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study on the fiber orientation variation due to bubble effect in fiber reinforced microcellular injection molding

    by Le Ke, Jun-Zheng Wang, Chao-Tsai (Ct) Huang, Shyh-Shin Hwang, Rong-Yeu Chang

    Due to its great functionality, the fiber reinforced thermoplastics (FRP) has been applied in industrial as one of the lightweight technologies for many years. However, the non-uniform shrinkage and warpage due to the fiber microstructure becomes one of the big challenges. To overcome the shrinkage and warpage problems, the bubbles introduced by microcellular process can be one of the solutions in FRP system. To date, how is the bubble effect on the fiber orientation is still not fully understood yet. In this study, the influence of the bubble on the fiber orientation through microcellular and conventional injection molding processes is investigated. Specifically, the bubble effect on the fiber orientation distribution (FOD) in conventional and microcellular injection molding has been conducted through Moldex3D 2020 version. Results showed that when the lower gas content is introduced into molten plastics, the generation of bigger bubble with lower concentration will enhance the fiber orientation in flow direction. Moreover, when more gas amount is introduced, the appearance of those increasing numbers of the smaller bubbles will push fibers orientation turn into the cross-flow direction. This phenomenon can be validated via experimental study. However, the FOD variation due to the bubble growth is not significantly in the real injection system. The interaction between the bubbles and fibers needs to be further decoupled which is our future work.


  • Open Access

    Investigation of Parameter Sensitivity and the Physical Mechanism for the Formation of a Core-Skin-Core (CSC) Structure in Two-Stage Co-Injection Molding

    by Chao-Tsai Huang, You-Ti Rao, Kuan-Yu Ko, Chih-Chung Hsu, You-Sheng Zhou, Chia-Hsiang Hsu, Rong-Yue Chang, Shi-Chang Tseng, Likey Chen

    One of the main challenges in co-injection molding is how to predict the skin to core morphology accurately and then manage it properly, especially after skin material has been broken through. In this study, the formation of the Core-Skin-Core (CSC) structure and its physical mechanism in a two-stage co-injection molding has been studied based on the ASTM D638 TYPE V system by using both numerical simulation and experimental observation. Results showed that when the skin to core ratio is selected properly (say 30/70), the CSC structure can be observed clearly at central location for 30SFPP/30SFPP system. When the skin to core ratio and operation conditions are fixed, regardless of material arrangement (including 30SFPP/30SFPP; PP/PP; 30SFPP/PP; and PP/30SFPP systems), the morphologies of the CSC structures are very close for all systems. This CSC structure can be further validated by using μ-CT scan and image analysis technologies perfectly. Furthermore, the influences of various operation parameters on the CSC structure variation have been investigated. Results exhibited that the CSC structure does not change significantly irrespective of the flow rate changing, melt temperature varying, or even mold temperature being modified. Moreover, the mechanism to generate the CSC structure can be derived using the melt front movement of the numerical simulation. It is worth noting that after the skin material was broken through, the core material travelled ahead with fountain flow to occupy the flow front. In the same period, the proper amount of skin material with certain inertia of enough kinetic energy will keep going to penetrate the new coming core material to travel until the end of filling. It ends up with this special CSC structure.


  • Open Access

    Sensor Fusion for Simultaneous Estimation of In-Plane Permeability and Porosity of Fiber Reinforcement in Resin Transfer Molding

    by Wei Qi, Tzu-Heng Chiu, Yi-Kai Kao, Yuan Yao, Yu-Ho Chen, Hsun Yang, Chen-Chieh Wang, Chia-Hsiang Hsu, Rong-Yeu Chang

    To meet the expectation of the industry, resin transfer molding (RTM) has become one of the most promising polymer processing methods to manufacture fiber-reinforced plastics (FRPs) with light weight, high strength, and multifunctional features. The permeability and porosity of fiber reinforcements are two of the primary properties that control the flow of resin in fibers and are critical to numerical simulations of RTM. In the past, various permeability measurement methods have been developed in the literature. However, limitations still exist. Furthermore, porosity is often measured independently of permeability. As a result, the two measurements do not necessarily relate to the same entity, which may increase the time and labor costs associated with experiments and affect result interpretation. In this work, a measurement system was developed by fusing the signals from capacitive sensing and flow visualization, based on which a novel algorithm was developed. Without complicated sensor design or expensive instrumentation, both in-plane permeability and porosity can be simultaneously estimated. The feasibility of the proposed method was illustrated by experiments and verified with numerical simulations.


  • Open Access

    Retrieving Equivalent Shear Viscosity for Molten Polymers from 3-D Nonisothermal Capillary Flow Simulation

    by Yu-Ho Wen, Chen-Chieh Wang, Guo-Sian Cyue, Rong-Hao Kuo, Chia-Hsiang Hsu, Rong-Yeu Chang

    For highly viscous polymer melts, considerable fluid temperature rises produced by viscous heating can be a disturbing factor in viscosity measurements. By scrutinizing the experimental and simulated capillary pressure losses for polymeric liquids, we demonstrate the importance of applying a viscous heating correction to the shear viscosity, so as to correct for large errors introduced by the undesirable temperature rises. Specifically, on the basis of a theoretical derivation and 3-D nonisothermal flow simulation, an approach is developed for retrieving the equivalent shear viscosity in capillary rheometry, and we show that the shear viscosity can be evaluated by using the average fluid temperature at the wall, instead of the bulk temperature, as previously assumed. With the help of a viscous Cross model in analyzing the shear-dominated capillary flow, it is possible to extract the viscous heating contribution to capillary pressure loss, and the general validity of the methodology is assessed using the experiments on a series of thermoplastic melts, including polymers of amorphous, crystalline, and filler-reinforced types. The predictions of the viscous model based on the equivalent viscosity are found to be in good to excellent agreement with experimental pressure drops. For all the materials studied, a near material-independent scaling relation between the dimensionless temperature rise (Θ) and the Nahme number (Na) is found, Θ ~ Na0.72, from which the fluid temperature rise due to viscous heating as well as the resultant viscosity change can be predicted.


  • The use of principal spatial tensor to predict anisotropic fiber orientation in concentrated fiber suspensions

    by Huan-Chang Tseng, Rong-Yeu Chang, Chia-Hsiang Hsu

    The Phelps-Tucker anisotropic rotary diffusion (ARD) equation constitutes an important development in relation to concentrated fiber suspension rheology and is significant in its ability to predict transient, flow-induced fiber orientation, especially for long fiber composites in the industry. Within this model, a critical spatial tensor was assumed to be a polynomial tensor-valued function depending on both the orientation tensor and the rate-of-strain tensor. However, it can be difficult to derive a large number of fitting ARD parameters. For simplification, we newly defined the spatial tensor as coaxial with the orientation tensor's principal directions, while the spatial tensor's principal components are to control anisotropic changes in the orientation tensor. Such a principal spatial tensor used in the Phelps-Tucker ARD model is demonstrated in accurately predicting the shell-core structure of fiber orientation distributions for injection molding simulation of long fiber composites, supported with e...


  • Dynamic penetration behavior of core-material in multi-cavity co-injection molding

    by Chao-Tsai (Ct) Huang, Jackie Yang, Rong-Yeu Chang

    Co-Injection Molding and multi-cavity molding are very common processes for plastic manufacturing. These two systems are sometimes combined and applied to some structure products. The core penetration and flow balance control problems are very difficult to manage. The inside mechanism of co-injection multi-cavity system is not fully figured out yet. In this study, we have focused on the penetration phenomena of core-material in a co-injection multi-cavity molding. The dynamic penetration behavior of core is very sensitive to injection flow rate and skin/core ratio. The longest core penetration has been shown to change dramatically from one runner to the other. In addition, the core penetration behavior will display imbalance at the end of filling. The more core ratio it is, the longer core penetration flows through runner to cavity. However, due to the multi-cavity geometrical structure, the balance of the core penetration for multi-cavity is still challenging. Finally, the simulation is validated with some literature. The results showed that both simulation and experiment are in a good agreement in trend