Chia-Hsiang Hsu
Chia-Hsiang Hsu has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Jiing-Yih Lai
National Central University, Taoyuan, Taiwan
8 shared publications - Ming-Hsuan Wang
National Central University, Taoyuan, Taiwan
5 shared publications - Yao-Chen Tsai
CoreTech System (Moldex3D) Co., Ltd., Hsinchu, Taiwan
5 shared publications - Pei-Pu Song
National Central University, Taoyuan, Taiwan
4 shared publications - Rong-Yeu Chang
CoreTech System (Moldex3D) Co., Ltd., Hsinchu, Taiwan
4 shared publications Yao-Chen Tsai
3 shared publications
Latest Publications
- Open Access
Investigation of Parameter Sensitivity and the Physical Mechanism for the Formation of a Core-Skin-Core (CSC) Structure in Two-Stage Co-Injection Molding
One of the main challenges in co-injection molding is how to predict the skin to core morphology accurately and then manage it properly, especially after skin material has been broken through. In this study, the formation of the Core-Skin-Core (CSC) structure and its physical mechanism in a two-stage co-injection molding has been studied based on the ASTM D638 TYPE V system by using both numerical simulation and experimental observation. Results showed that when the skin to core ratio is selected properly (say 30/70), the CSC structure can be observed clearly at central location for 30SFPP/30SFPP system. When the skin to core ratio and operation conditions are fixed, regardless of material arrangement (including 30SFPP/30SFPP; PP/PP; 30SFPP/PP; and PP/30SFPP systems), the morphologies of the CSC structures are very close for all systems. This CSC structure can be further validated by using μ-CT scan and image analysis technologies perfectly. Furthermore, the influences of various operation parameters on the CSC structure variation have been investigated. Results exhibited that the CSC structure does not change significantly irrespective of the flow rate changing, melt temperature varying, or even mold temperature being modified. Moreover, the mechanism to generate the CSC structure can be derived using the melt front movement of the numerical simulation. It is worth noting that after the skin material was broken through, the core material travelled ahead with fountain flow to occupy the flow front. In the same period, the proper amount of skin material with certain inertia of enough kinetic energy will keep going to penetrate the new coming core material to travel until the end of filling. It ends up with this special CSC structure.
Open AccessInvestigation of Parameter Sensitivity and the Physical Mechanism for the Formation of a Core-Skin-Core (CSC) Structure in Two-Stage Co-Injection Molding
One of the main challenges in co-injection molding is how to predict the skin to core morphology accurately and then manage it properly, especially after skin material has been broken through. In this study, the formation of the Core-Skin-Core (CSC) structure and its physical mechanism in a two-stage co-injection molding has been studied based on the ASTM D638 TYPE V system by using both numerical simulation and experimental observation. Results showed that when the skin to core ratio is selected properly (say 30/70), the CSC structure can be observed clearly at central location for 30SFPP/30SFPP system. When the skin to core ratio and operation conditions are fixed, regardless of material arrangement (including 30SFPP/30SFPP; PP/PP; 30SFPP/PP; and PP/30SFPP systems), the morphologies of the CSC structures are very close for all systems. This CSC structure can be further validated by using μ-CT scan and image analysis technologies perfectly. Furthermore, the influences of various operation parameters on the CSC structure variation have been investigated. Results exhibited that the CSC structure does not change significantly irrespective of the flow rate changing, melt temperature varying, or even mold temperature being modified. Moreover, the mechanism to generate the CSC structure can be derived using the melt front movement of the numerical simulation. It is worth noting that after the skin material was broken through, the core material travelled ahead with fountain flow to occupy the flow front. In the same period, the proper amount of skin material with certain inertia of enough kinetic energy will keep going to penetrate the new coming core material to travel until the end of filling. It ends up with this special CSC structure.
- Open Access
Sensor Fusion for Simultaneous Estimation of In-Plane Permeability and Porosity of Fiber Reinforcement in Resin Transfer Molding
To meet the expectation of the industry, resin transfer molding (RTM) has become one of the most promising polymer processing methods to manufacture fiber-reinforced plastics (FRPs) with light weight, high strength, and multifunctional features. The permeability and porosity of fiber reinforcements are two of the primary properties that control the flow of resin in fibers and are critical to numerical simulations of RTM. In the past, various permeability measurement methods have been developed in the literature. However, limitations still exist. Furthermore, porosity is often measured independently of permeability. As a result, the two measurements do not necessarily relate to the same entity, which may increase the time and labor costs associated with experiments and affect result interpretation. In this work, a measurement system was developed by fusing the signals from capacitive sensing and flow visualization, based on which a novel algorithm was developed. Without complicated sensor design or expensive instrumentation, both in-plane permeability and porosity can be simultaneously estimated. The feasibility of the proposed method was illustrated by experiments and verified with numerical simulations.
Open AccessSensor Fusion for Simultaneous Estimation of In-Plane Permeability and Porosity of Fiber Reinforcement in Resin Transfer Molding
To meet the expectation of the industry, resin transfer molding (RTM) has become one of the most promising polymer processing methods to manufacture fiber-reinforced plastics (FRPs) with light weight, high strength, and multifunctional features. The permeability and porosity of fiber reinforcements are two of the primary properties that control the flow of resin in fibers and are critical to numerical simulations of RTM. In the past, various permeability measurement methods have been developed in the literature. However, limitations still exist. Furthermore, porosity is often measured independently of permeability. As a result, the two measurements do not necessarily relate to the same entity, which may increase the time and labor costs associated with experiments and affect result interpretation. In this work, a measurement system was developed by fusing the signals from capacitive sensing and flow visualization, based on which a novel algorithm was developed. Without complicated sensor design or expensive instrumentation, both in-plane permeability and porosity can be simultaneously estimated. The feasibility of the proposed method was illustrated by experiments and verified with numerical simulations.
- Open Access
Retrieving Equivalent Shear Viscosity for Molten Polymers from 3-D Nonisothermal Capillary Flow Simulation
For highly viscous polymer melts, considerable fluid temperature rises produced by viscous heating can be a disturbing factor in viscosity measurements. By scrutinizing the experimental and simulated capillary pressure losses for polymeric liquids, we demonstrate the importance of applying a viscous heating correction to the shear viscosity, so as to correct for large errors introduced by the undesirable temperature rises. Specifically, on the basis of a theoretical derivation and 3-D nonisothermal flow simulation, an approach is developed for retrieving the equivalent shear viscosity in capillary rheometry, and we show that the shear viscosity can be evaluated by using the average fluid temperature at the wall, instead of the bulk temperature, as previously assumed. With the help of a viscous Cross model in analyzing the shear-dominated capillary flow, it is possible to extract the viscous heating contribution to capillary pressure loss, and the general validity of the methodology is assessed using the experiments on a series of thermoplastic melts, including polymers of amorphous, crystalline, and filler-reinforced types. The predictions of the viscous model based on the equivalent viscosity are found to be in good to excellent agreement with experimental pressure drops. For all the materials studied, a near material-independent scaling relation between the dimensionless temperature rise (Θ) and the Nahme number (Na) is found, Θ ~ Na0.72, from which the fluid temperature rise due to viscous heating as well as the resultant viscosity change can be predicted.
Open AccessRetrieving Equivalent Shear Viscosity for Molten Polymers from 3-D Nonisothermal Capillary Flow Simulation
For highly viscous polymer melts, considerable fluid temperature rises produced by viscous heating can be a disturbing factor in viscosity measurements. By scrutinizing the experimental and simulated capillary pressure losses for polymeric liquids, we demonstrate the importance of applying a viscous heating correction to the shear viscosity, so as to correct for large errors introduced by the undesirable temperature rises. Specifically, on the basis of a theoretical derivation and 3-D nonisothermal flow simulation, an approach is developed for retrieving the equivalent shear viscosity in capillary rheometry, and we show that the shear viscosity can be evaluated by using the average fluid temperature at the wall, instead of the bulk temperature, as previously assumed. With the help of a viscous Cross model in analyzing the shear-dominated capillary flow, it is possible to extract the viscous heating contribution to capillary pressure loss, and the general validity of the methodology is assessed using the experiments on a series of thermoplastic melts, including polymers of amorphous, crystalline, and filler-reinforced types. The predictions of the viscous model based on the equivalent viscosity are found to be in good to excellent agreement with experimental pressure drops. For all the materials studied, a near material-independent scaling relation between the dimensionless temperature rise (Θ) and the Nahme number (Na) is found, Θ ~ Na0.72, from which the fluid temperature rise due to viscous heating as well as the resultant viscosity change can be predicted.
- 24 June 2019
- Published by U-turn Press LLC
Recognition and Simplification of Holes in CAD Models of an Injection Mold for Mold Flow Analysis
In mold flow analysis, it is necessary to convert the computer-aided design (CAD) models of an injection mold into solid meshes during the analysis. The main components of an injection mold that need to be modeled are the core, cavity, runner system, cooling channels, and the mold base. Traditionally, a mold base is modeled as a rectangular box to simplify the mold structure. However, in some applications, it is necessary to consider the non-simplified, original plates of the mold base in order to increase the accuracy of the mold flow analysis. As more components of the mold are involved and meshed, the total number of mesh nodes increases. Therefore, mesh reduction becomes an important issue to study. Typical mold plates on a mold base are clamping plates, cavity plates, stripper plates, core plates, support plates, spacer blocks, locating plates, and ejector clamping plates. Holes are a common feature in these components. If all holes are preserved and meshed, then, because the mesh size near holes should be smaller, a tremendous amount of nodes would be generated. On the contrary, if most holes on mold plates are simplified, then the total amount of nodes can be substantially reduced.
- 24 June 2019
- Published by U-turn Press LLC
Recognition and Simplification of Holes in CAD Models of an Injection Mold for Mold Flow Analysis
In mold flow analysis, it is necessary to convert the computer-aided design (CAD) models of an injection mold into solid meshes during the analysis. The main components of an injection mold that need to be modeled are the core, cavity, runner system, cooling channels, and the mold base. Traditionally, a mold base is modeled as a rectangular box to simplify the mold structure. However, in some applications, it is necessary to consider the non-simplified, original plates of the mold base in order to increase the accuracy of the mold flow analysis. As more components of the mold are involved and meshed, the total number of mesh nodes increases. Therefore, mesh reduction becomes an important issue to study. Typical mold plates on a mold base are clamping plates, cavity plates, stripper plates, core plates, support plates, spacer blocks, locating plates, and ejector clamping plates. Holes are a common feature in these components. If all holes are preserved and meshed, then, because the mesh size near holes should be smaller, a tremendous amount of nodes would be generated. On the contrary, if most holes on mold plates are simplified, then the total amount of nodes can be substantially reduced.
- 23 May 2019
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 17 (1)
Recognition and Simplification of Holes in CAD Models of an Injection Mold for Mold Flow Analysis
- 23 May 2019
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 17 (1)
Recognition and Simplification of Holes in CAD Models of an Injection Mold for Mold Flow Analysis
- 1 January 2018
- Published by Society of Rheology in Journal of Rheology
- Vol. 62 (1) , 313-320
The use of principal spatial tensor to predict anisotropic fiber orientation in concentrated fiber suspensions
The Phelps-Tucker anisotropic rotary diffusion (ARD) equation constitutes an important development in relation to concentrated fiber suspension rheology and is significant in its ability to predict transient, flow-induced fiber orientation, especially for long fiber composites in the industry. Within this model, a critical spatial tensor was assumed to be a polynomial tensor-valued function depending on both the orientation tensor and the rate-of-strain tensor. However, it can be difficult to derive a large number of fitting ARD parameters. For simplification, we newly defined the spatial tensor as coaxial with the orientation tensor's principal directions, while the spatial tensor's principal components are to control anisotropic changes in the orientation tensor. Such a principal spatial tensor used in the Phelps-Tucker ARD model is demonstrated in accurately predicting the shell-core structure of fiber orientation distributions for injection molding simulation of long fiber composites, supported with e...
- 1 January 2018
- Published by Society of Rheology in Journal of Rheology
- Vol. 62 (1) , 313-320
The use of principal spatial tensor to predict anisotropic fiber orientation in concentrated fiber suspensions
The Phelps-Tucker anisotropic rotary diffusion (ARD) equation constitutes an important development in relation to concentrated fiber suspension rheology and is significant in its ability to predict transient, flow-induced fiber orientation, especially for long fiber composites in the industry. Within this model, a critical spatial tensor was assumed to be a polynomial tensor-valued function depending on both the orientation tensor and the rate-of-strain tensor. However, it can be difficult to derive a large number of fitting ARD parameters. For simplification, we newly defined the spatial tensor as coaxial with the orientation tensor's principal directions, while the spatial tensor's principal components are to control anisotropic changes in the orientation tensor. Such a principal spatial tensor used in the Phelps-Tucker ARD model is demonstrated in accurately predicting the shell-core structure of fiber orientation distributions for injection molding simulation of long fiber composites, supported with e...
- 6 October 2017
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 15 (2) , 264-279
Recognition and decomposition of rib features in thin-shell plastic parts for finite element analysis
Feature recognition has been extensively studied for applications in computer-aided design (CAD), computer-aided manufacturing, and computer-aided process planning. However, its application in finite element analysis (FEA) is limited. The primary motivation for applying feature recognition in FEA is to facilitate high-quality mesh generation, which requires not only identifying the geometric entities of a feature but also decomposing and computing the region data. This study proposes an approach based on feature recognition to recognize ribs from a CAD model and decompose them into regions that can be meshed with hexahedral or prismatic meshes. Ribs in a CAD model are generally connected to form a complex structure. A rib recognition algorithm to recognize all faces belonging to a rib structure is proposed, and a rib decomposition algorithm was also developed to decompose the rib structure into rib segment and transition regions. After both types of region were defined, the data to decompose each of them from the CAD model was computed. Several examples are presented to verify the results of the rib recognition and demonstrate the feasibility of the proposed rib decomposition algorithm.
- 6 October 2017
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 15 (2) , 264-279
Recognition and decomposition of rib features in thin-shell plastic parts for finite element analysis
Feature recognition has been extensively studied for applications in computer-aided design (CAD), computer-aided manufacturing, and computer-aided process planning. However, its application in finite element analysis (FEA) is limited. The primary motivation for applying feature recognition in FEA is to facilitate high-quality mesh generation, which requires not only identifying the geometric entities of a feature but also decomposing and computing the region data. This study proposes an approach based on feature recognition to recognize ribs from a CAD model and decompose them into regions that can be meshed with hexahedral or prismatic meshes. Ribs in a CAD model are generally connected to form a complex structure. A rib recognition algorithm to recognize all faces belonging to a rib structure is proposed, and a rib decomposition algorithm was also developed to decompose the rib structure into rib segment and transition regions. After both types of region were defined, the data to decompose each of them from the CAD model was computed. Several examples are presented to verify the results of the rib recognition and demonstrate the feasibility of the proposed rib decomposition algorithm.
- 10 August 2017
- Published by U-turn Press LLC
Recognition and Decomposition of Rib Features in Thin-Shell Plastic Parts for Finite Element Analysis
Mold flow analysis is commonly used in injection molding to assist in designing injection molds as well as setting the process parameters. In mold flow analysis, it is necessary to convert the computer-aided design (CAD) model into solid meshes so that the solver can perform computations. Traditionally, tetrahedral meshes are used because they are easy to generate automatically, but this type of mesh is of the lowest quality compared with other types (e.g., pyramidal, prismatic, or hexahedral). Hexahedral meshes are highly preferable to tetrahedral meshes for their greater accuracy, convergence, and application specificity. However, hexahedral meshes are inherently trickier to generate because they require the careful decomposition of the CAD model. The generation of entirely hexahedral meshes on a CAD model may be difficult, but a hybrid combination of hexahedral and prismatic meshes is possible and can solve the problems of tetrahedral meshes.
- 10 August 2017
- Published by U-turn Press LLC
Recognition and Decomposition of Rib Features in Thin-Shell Plastic Parts for Finite Element Analysis
Mold flow analysis is commonly used in injection molding to assist in designing injection molds as well as setting the process parameters. In mold flow analysis, it is necessary to convert the computer-aided design (CAD) model into solid meshes so that the solver can perform computations. Traditionally, tetrahedral meshes are used because they are easy to generate automatically, but this type of mesh is of the lowest quality compared with other types (e.g., pyramidal, prismatic, or hexahedral). Hexahedral meshes are highly preferable to tetrahedral meshes for their greater accuracy, convergence, and application specificity. However, hexahedral meshes are inherently trickier to generate because they require the careful decomposition of the CAD model. The generation of entirely hexahedral meshes on a CAD model may be difficult, but a hybrid combination of hexahedral and prismatic meshes is possible and can solve the problems of tetrahedral meshes.
- 22 November 2016
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 14 (4) , 450-463
Boss recognition algorithm for application to finite element analysis
In finite element analysis (FEA), computer-aided design (CAD) models must be converted into solid meshes so that the solver can perform the desired analysis and simulation. Hexahedral and prism meshes are better than tetrahedral meshes, but are inherently more complex and difficult to generate. The purpose of this study was to propose an approach based on feature recognition for generating better quality solid meshes for FEA applications. Particularly, this study focused on the development of a boss recognition algorithm, the output of boss data for meshing, and the development of a process for automatic boss meshing. The proposed boss recognition method contains three parts: the preliminary functions, the data base, and the boss recognition. The first two parts provide a framework that can be used for other types of feature recognition. The core of the boss recognition is the tube recognition, which involves five main steps of validation. The output data of a boss includes the rib, tube, and hole data, which record not only feature data, but also the meshing data that can be used for automatic meshing. The meshing of a boss is divided into rib meshing and tube meshing. Both hexahedral meshes and prism meshes may be used depending on the regularity and orthogonality of the shape. This paper provides a detailed description of the proposed algorithm and presents several examples to illustrate its feasibility.
- 22 November 2016
- Published by U-turn Press LLC in Computer-Aided Design and Applications
- Vol. 14 (4) , 450-463
Boss recognition algorithm for application to finite element analysis
In finite element analysis (FEA), computer-aided design (CAD) models must be converted into solid meshes so that the solver can perform the desired analysis and simulation. Hexahedral and prism meshes are better than tetrahedral meshes, but are inherently more complex and difficult to generate. The purpose of this study was to propose an approach based on feature recognition for generating better quality solid meshes for FEA applications. Particularly, this study focused on the development of a boss recognition algorithm, the output of boss data for meshing, and the development of a process for automatic boss meshing. The proposed boss recognition method contains three parts: the preliminary functions, the data base, and the boss recognition. The first two parts provide a framework that can be used for other types of feature recognition. The core of the boss recognition is the tube recognition, which involves five main steps of validation. The output data of a boss includes the rib, tube, and hole data, which record not only feature data, but also the meshing data that can be used for automatic meshing. The meshing of a boss is divided into rib meshing and tube meshing. Both hexahedral meshes and prism meshes may be used depending on the regularity and orthogonality of the shape. This paper provides a detailed description of the proposed algorithm and presents several examples to illustrate its feasibility.
- 27 June 2016
- Published by U-turn Press LLC
Boss Recognition Algorithm and Application to Finite Element Analysis
- 27 June 2016
- Published by U-turn Press LLC
Boss Recognition Algorithm and Application to Finite Element Analysis