Toshikazu Akahori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Toshikazu Akahori has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Mitsuo Niinomi
Institute for Materials Research, Tohoku University, Sendai 980-8577, Japan
2 shared publications - Yuki Nakamura
Department of Mechanical Engineering, National Institute of Technology 1 , Toyota College, Toyota, 2-1 Eisei-cho, Aichi, 471-8525
2 shared publications - Agri Suwandi
Universitas Pancasila
1 shared publication - Gunawarman Gunawarman
Universitas Andalas
1 shared publication - Gunawarman Gunawarman
Universitas Andalas
1 shared publication - Ilhamdi
Mechanical Engineering Department, Faculty of Engineering, Andalas University, Padang, 25163, Indonesia
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2592 (1) , 030012
Contribution of hydroxyapatite layer on corrosion and bioactivity properties of Ti-12Cr in simulated body fluid
Biomaterial implant is a material use for biomedical applications such as for fixing bone fractures. One of materials used in this application is titanium and i
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2592 (1) , 030012
Open AccessContribution of hydroxyapatite layer on corrosion and bioactivity properties of Ti-12Cr in simulated body fluid
Biomaterial implant is a material use for biomedical applications such as for fixing bone fractures. One of materials used in this application is titanium and i
- Open Access
- 6 July 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 96 (1) , 127-136
The Influence of Thermal Oxidation on Hardness and Microstructure of Beta-Type Titanium Alloy Ti-29Nb-13Ta-4.6Zr (TNTZ)
Thermal oxidation is one of the simple and low-cost methods that can improve tribological characteristics of titanium and its alloys by generating a protective layer on their surfaces. In this study, the experiment parameters were applied on thermal oxidation (TO) at 598, 673 and 723K for 40, 50 and 60s on TNTZ. The micro-Vickers hardness tests and microstructure analysis were performed for specimens before and after TO. The results exhibited that the hardness of TNTZ was increased by increasing TO temperature, but it was decreased by enlarging of TO time. Metallographic tests showed that oxidised TNTZ have equaxial β grains with a grain size approximately about 20-30μm. No significant change of microstructure (grain size) was detected after increasing TO temperature because the short time oxidation process was applied.
- 6 July 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 96 (1) , 127-136
Open AccessThe Influence of Thermal Oxidation on Hardness and Microstructure of Beta-Type Titanium Alloy Ti-29Nb-13Ta-4.6Zr (TNTZ)
Thermal oxidation is one of the simple and low-cost methods that can improve tribological characteristics of titanium and its alloys by generating a protective layer on their surfaces. In this study, the experiment parameters were applied on thermal oxidation (TO) at 598, 673 and 723K for 40, 50 and 60s on TNTZ. The micro-Vickers hardness tests and microstructure analysis were performed for specimens before and after TO. The results exhibited that the hardness of TNTZ was increased by increasing TO temperature, but it was decreased by enlarging of TO time. Metallographic tests showed that oxidised TNTZ have equaxial β grains with a grain size approximately about 20-30μm. No significant change of microstructure (grain size) was detected after increasing TO temperature because the short time oxidation process was applied.
- Open Access
- 10 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (9) , 4307
Effect of Fine Particle Peening Using Hydroxyapatite Particles on Rotating Bending Fatigue Properties of β-Type Titanium Alloy
Fine particle peening (FPP) using hydroxyapatite (HAp) shot particles was performed to improve the fatigue strength and form a HAp transfer layer on a beta titanium alloy (Ti–22V–4Al). The surface microstructures of the FPP-treated specimen were characterized using scanning electron microscopy, micro-Vickers hardness testing, energy dispersive X-ray spectrometry, X-ray diffraction, and electron backscattered diffraction. A HAp transfer layer with a thickness of 5.5 μm was formed on the surface of the Ti–22V–4Al specimen by FPP. In addition, the surface hardness of the Ti–22V–4Al was increased, and high compressive residual stress was generated on the specimen surface by FPP. Rotating bending fatigue tests were performed at room temperature in laboratory air over a wide cycle-life region (103–109 cycles). In the long cycle-life regime, the fatigue strength at 107 cycles of the FPP-treated specimen became higher than that of the untreated specimen. This result is attributed to the formation of a work-hardened layer with high compressive residual stress by FPP. However, the fatigue strength was not improved by FPP in the short cycle-life regime, because fatigue cracks were initiated at surface defects formed during the FPP process. The fatigue fracture mode of the FPP-treated specimens shifted from surface-initiated fracture to subsurface-initiated fracture at a stress amplitude level of 600 MPa.
- 10 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (9) , 4307
Open AccessEffect of Fine Particle Peening Using Hydroxyapatite Particles on Rotating Bending Fatigue Properties of β-Type Titanium Alloy
Fine particle peening (FPP) using hydroxyapatite (HAp) shot particles was performed to improve the fatigue strength and form a HAp transfer layer on a beta titanium alloy (Ti–22V–4Al). The surface microstructures of the FPP-treated specimen were characterized using scanning electron microscopy, micro-Vickers hardness testing, energy dispersive X-ray spectrometry, X-ray diffraction, and electron backscattered diffraction. A HAp transfer layer with a thickness of 5.5 μm was formed on the surface of the Ti–22V–4Al specimen by FPP. In addition, the surface hardness of the Ti–22V–4Al was increased, and high compressive residual stress was generated on the specimen surface by FPP. Rotating bending fatigue tests were performed at room temperature in laboratory air over a wide cycle-life region (103–109 cycles). In the long cycle-life regime, the fatigue strength at 107 cycles of the FPP-treated specimen became higher than that of the untreated specimen. This result is attributed to the formation of a work-hardened layer with high compressive residual stress by FPP. However, the fatigue strength was not improved by FPP in the short cycle-life regime, because fatigue cracks were initiated at surface defects formed during the FPP process. The fatigue fracture mode of the FPP-treated specimens shifted from surface-initiated fracture to subsurface-initiated fracture at a stress amplitude level of 600 MPa.
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2017, J0250103
Formation of Hydroxyapatite Layer on the Aged Biomedical Titanium Alloy by Means of Fine Particle Peening
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2017, J0250103
Formation of Hydroxyapatite Layer on the Aged Biomedical Titanium Alloy by Means of Fine Particle Peening