GAGeorg Atzl

Georg Atzl

*This is an algorithmically generated author record based on publicly available information.

Georg Atzl has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Structural design of precast segmental lining reinforced by steel fibres

    by Vincenzo Zeuli, Christof Maier, José Manuel Suarez Diaz, Fahed Ahmed Saeed, Jayapregasham Tharamapalan, Carlo Germani, Lars Bayer, Georg Atzl


  • Neubau Albulatunnel II – Erfahrungen mit Stahlfaserspritzbeton

    by Reinhard Perner, Roland Schorn, Georg Atzl

    The new construction of the 5860 m long Albula Tunnel was mainly carried out by blasting from the Preda and Spinas portals. Due to the exposed location in the high mountains, mixing plants were installed on both portal sides for the concrete supply; the concrete aggregate was largely produced from the excavated material, with a gravel plant being built in Preda for this purpose. The planned tunnel lining provides for a single‐shell shotcrete construction for the most part. In the course of the excavation work, the excavation support was optimised so that the reinforcement mesh in the main support class in the single‐shell area were replaced by steel fibre shotcrete.


  • Gebirgsdruckabhängige Tübbing‐Öffnungsvarianten für Querschläge beim Koralmtunnel KAT3 – Entwicklung von Sicherungstypen zum Einfahren von Querschlagvortrieben in Tübbingröhre

    by Georg Atzl, Gerd Josmann, Werner Fleissner, Bernd Moritz, Dieter Handke, Jaka Zevnik, Karl Schiesser, Andreas Kiesling

    The southern tube of the Koralm Tunnel, contract KAT3, is being conventionally excavated with two‐pass lining, while the northern tube is being driven by TBM with single‐pass segment lining. The tunnel tubes are located in quite different geotechnical conditions, with soft ground of high and low permeability, major fault zones and hard rock. Cross passages are provided about every 500 m of the 12 km long tunnel section. Different support types are required for the opening of the segment lining and connection to the excavation of the cross passage. In hard rock, the support consists of anchors, tail void grout and permanent bolts between the segments. In soft ground, a temporary pre‐stressed steel structure is provided, with longitudinal dowels at ring joints and special segments with increased reinforcement for the special case where cross passage excavation enters the segment‐lined tunnel.


  • TBM research project – Tolerances segmental lining / TVM‐Forschungsprojekt – Toleranzen Tübbingausbau

    by Alois Vigl, Andreas Walter, Johann Lemmerer, Georg Atzl, Dieter Handke

    In infrastructure tunnelling projects with shielded TBMs, prefabricated segmental linings are used with various systems and requirements. The required degree of accuracy in segment production and ring assembly is a considerable factor in terms of equipment, time and costs. The required tolerances for segments and ring assembly depend significantly on the segment geometry, lining system and field of application. In order to provide a reasonable basis for allowable segment and installation tolerances, a new approach has been established as part of a research initiative of the ÖBB‐Infrastruktur AG with respect to the risks and consequences arising from geometrical tolerances. The paper explains the concept of “tolerance classes” with the approach for their developments, derivation and classification. A practical application example is shown in addition. With respect to the nomenclature of tolerances, a harmonization process has been performed in collaboration with the German committees for underground structures, ZTV‐ING and DAUB. The results of harmonizing and proposals of tolerance clarifications are presented within this paper.Toleranzklassen, Harmonisierung der Toleranzbegriffe und Toleranzanforderungen Erfahrungsstand 2016Bei maschinellen Schildvortrieben kommen Tübbingauskleidungen mit unterschiedlichen Systemen und Anforderungen zum Einsatz. Die erforderliche Genauigkeit in der Herstellung der Fertigteilsegmente sowie beim Ringbau gewinnt immer mehr an Bedeutung für eine wirtschaftliche Auslegung der Auskleidung, gekoppelt an die spezifischen Anforderungen des Projekts. Das erforderliche Maß an die Genauigkeit der Tübbinge und den Einbau im Tunnel hängt im Wesentlichen von der Tübbinggeometrie, vom Tübbingsystem und vom jeweiligen Anwendungsbereich ab. Im Arbeitskreis “TVM‐Forschungsprojekt Toleranzen”, einer Forschungsinitiative der ÖBB‐Infrastruktur AG, wurde ein neuer Ansatz für die Herleitung zulässiger Herstell‐ und Einbautoleranzen unter Einbeziehung einer Risikobetrachtung entwickelt. Im vorliegenden Beitrag wird die Herangehensweise für die Entwicklung, Herleitung und Klassifizierung von Toleranzgruppen, die unter dem Namen “Toleranzklassen” geführt werden, beschrieben. Ergänzend wird auch ein Beispiel für die Anwendung des vorgestellten Konzepts gezeigt. Im Zusammenhang mit den Toleranzklassen erfolgte eine Harmonisierung von Toleranzbegriffen in Zusammenarbeit mit deutschen Ausschüssen wie der ZTV‐ING und des DAUB. Die wesentlichen Änderungen und Ergänzungen der Toleranzbegriffe sowie Erläuterungen werden im Anschluss an das erwähnte Konzept der Toleranzklassen vorgestellt.


  • Planning of tunnel excavation for the Vienna underground – construction Lot U1/9 / Planung der Tunnelvortriebe für die Wiener U‐Bahn – Bauabschnitt U1/9

    by Georg Atzl, Gerhard Ullmann, Martin Schmidt

    The extension of underground line U1 from Reumannplatz station to Oberlaa station, which includes construction lot U1/9, significantly enhances accessibility for local residents and workplaces, achieves optimal regional accessibility and improves connections to regional buses, a park & ride facility as well as easing the pressure on the Reumannplatz station. Starting from Reumannplatz, the U1 will increase by 4.6 km with five new stations in the forthcoming years. By 2017, it will be the longest underground line in Vienna (19.2 km).Planning for construction preparation and the detailed design of construction lot U1/9 is being carried out by the planning group PCD – FCP – iC in cooperation with Architektengruppe AGU. PCD, the lead planning partner, is responsible for planning of the cut‐and‐cover method, whilst iC is responsible for the design of the mined tunnel sections. Preliminary geotechnical work, main geotechnical investigations and geotechnical support during construction were undertaken by the municipal department MA 29 (bridge construction and ground engineering). Project management incl. controlling and site supervision is done by the Client (Abteilung Bau, Planung und Projektmanagement of Wiener Linien). The design for obtaining the building permit in accordance with the Austrian railway law was carried out in 2009 and 2010 and approval was given in January 2011. Tenders were first drafted in 2010, and were published in the summer of 2011. The tender was awarded to the Strabag company. Construction started in the spring of 2012. Tunnel excavation commenced at the end of January 2014.Die Verlängerung der U‐Bahn‐Linie U1 von der Station Reumannplatz bis zur Station Oberlaa, zu der auch der Bauabschnitt U1/9 gehört, dient der Erschließung von Wohnquartieren, der regionalen Erreichbarkeit, der Anbindung an die Regionalbusse, beinhaltet eine Park & Ride‐Anlage und sorgt zusätzlich für eine Entlastung der Station Reumannplatz. Insgesamt wächst die U1 in den nächsten Jahren vom Reumannplatz ausgehend um 4,6 km und fünf Stationen. 2017 ist sie mit 19,2 km dann die längste U‐Bahnlinie Wiens.Die Planung des Bauabschnitts U1/9 wird durch die Planungsgemeinschaft PCD – FCP – iC in Zusammenarbeit mit der Architektengruppe AGU durchgeführt. PCD ist federführend zuständig für die Planung der offenen Bauweise. Für die Planung der geschlossenen Bauweise ist iC federführend verantwortlich. Die geotechnischen Vorarbeiten und Hauptuntersuchungen sowie die baubegleitende geotechnische Betreuung erfolgten durch die MA 29 Brückenbau und Grundbau. Die Aufgaben des Projektmanagements einschließlich Controlling und Steuerung sowie die örtliche Bauaufsicht werden vom Bauherrn selbst, durch die Abteilung Bau, Planung und Projektmanagement der Wiener Linien wahrgenommen. Die Planung für die eisenbahnrechtliche Baugenehmigung wurde in den Jahren 2009 und 2010 durchgeführt, der positive Bescheid wurde im Januar 2011 erteilt. Bereits im Jahr 2010 wurde mit der Planung der Ausschreibung begonnen, die im Sommer 2011 aufgelegt wurde. Den Zuschlag erhielt die Firma Strabag. Der Baubeginn erfolgte im Frühjahr 2012. Die Tunnelvortriebe wurden Ende Januar 2014 begonnen.