Milan Dej
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Milan Dej has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Lenka Kuboňová
Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic
5 shared publications - František Hopan
Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic
4 shared publications - Jiří Horák
Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic
4 shared publications - Jiří Ryšavý
Energy Research Centre, Centre for Energy and Environmental Technologies, VŠB—Technical University of Ostrava, 17. Listopadu 2172/15, 708 00 Ostrava, Czech Republic
4 shared publications - Kamil Krpec
Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic
2 shared publications - Oleksandr Molchanov
Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic
2 shared publications
Latest Publications
- Open Access
- 6 May 2025
- Published by Elsevier in Science of The Total Environment
- Vol. 981, 179564
In-situ investigation of real-world emissions from 111 measurements on solid fuel household boilers
- 6 May 2025
- Published by Elsevier in Science of The Total Environment
- Vol. 981, 179564
Open AccessIn-situ investigation of real-world emissions from 111 measurements on solid fuel household boilers
- Open Access
Co-Gasification of Pistachio Shells with Wood Pellets in a Semi-Industrial Hybrid Cross/Updraft Reactor for Producer Gas and Biochar Production
The possibilities of pistachio shell biochar production on laboratory-scale gasification and pyrolysis devices have been described by several previous studies. Nevertheless, the broader results of the pistachio shell co-gasification process on pilot-scale units have not yet been properly investigated or reported, especially regarding the detailed description of the biochar acquired during the routine operation. The biochar was analysed using several analytical techniques, such as ultimate and proximate analysis (62%wt of C), acid–base properties analysis (pH 9.52), Fourier-transform infrared spectroscopy (the presence of –OH bonds and identification of cellulose, hemicellulose and lignin), Raman spectroscopy (no determination of Id/Ig ratio due to high fluorescence), and nitrogen physisorption (specific surface 50.895 m2·g−1). X-ray fluorescence analysis exhibited the composition of the main compounds in the biochar ash (32.5%wt of Cl and 40.02%wt of Na2O). From the energy generation point of view, the lower heating value of the producer gas achieved 6.53 MJ·m−3 during the co-gasification. The relatively high lower heating value of the producer gas was mainly due to the significant volume fractions of CO (6.5%vol.), CH4 (14.2%vol.), and H2 (4.8 %vol.), while hot gas efficiency accomplished 89.6%.
Open AccessCo-Gasification of Pistachio Shells with Wood Pellets in a Semi-Industrial Hybrid Cross/Updraft Reactor for Producer Gas and Biochar Production
The possibilities of pistachio shell biochar production on laboratory-scale gasification and pyrolysis devices have been described by several previous studies. Nevertheless, the broader results of the pistachio shell co-gasification process on pilot-scale units have not yet been properly investigated or reported, especially regarding the detailed description of the biochar acquired during the routine operation. The biochar was analysed using several analytical techniques, such as ultimate and proximate analysis (62%wt of C), acid–base properties analysis (pH 9.52), Fourier-transform infrared spectroscopy (the presence of –OH bonds and identification of cellulose, hemicellulose and lignin), Raman spectroscopy (no determination of Id/Ig ratio due to high fluorescence), and nitrogen physisorption (specific surface 50.895 m2·g−1). X-ray fluorescence analysis exhibited the composition of the main compounds in the biochar ash (32.5%wt of Cl and 40.02%wt of Na2O). From the energy generation point of view, the lower heating value of the producer gas achieved 6.53 MJ·m−3 during the co-gasification. The relatively high lower heating value of the producer gas was mainly due to the significant volume fractions of CO (6.5%vol.), CH4 (14.2%vol.), and H2 (4.8 %vol.), while hot gas efficiency accomplished 89.6%.
- Open Access
Specifics of Electrostatic Precipitation of Fly Ash from Small-Scale Fossil Fuel Combustion
This paper investigates the removal efficiency of a honeycomb electrostatic precipitator (ESP) applied to control particulate matter (PM) emissions from a small-scale boiler with combustion lignite and hard coal. The specifics of the precipitation of emissions from small-scale boilers are discussed, and the design principles for relevant ESPs are presented and used. The ion-induced nucleation of sulfuric acid occurred, causing the drastic penetration of 19 nm particles through the ESP. Despite this, the overall collection efficiency was sufficient to meet the EU’s Ecodesign Directive requirements. Back corona was not detected. The optimal ESP performance is defined with further parameters: a current density of 0.5 mA/m2 at an electric field strength of about 2.7 × 105 V/m; a minimal specific collecting area of ESP (SCA) of 60 m2/(m3/s); and Nt-product of 4.5 × 1014 s/m3. Such parameters of ESPs should ensure adequate PM emissions control for any type of boiler with similar emissions characteristics. The composition of collected fly ash particles was analysed, and a method for fly ash utilisation was proposed. This research may be helpful for designing ESPs to control PM emissions for small-scale units with fossil fuel combustion.
Open AccessSpecifics of Electrostatic Precipitation of Fly Ash from Small-Scale Fossil Fuel Combustion
This paper investigates the removal efficiency of a honeycomb electrostatic precipitator (ESP) applied to control particulate matter (PM) emissions from a small-scale boiler with combustion lignite and hard coal. The specifics of the precipitation of emissions from small-scale boilers are discussed, and the design principles for relevant ESPs are presented and used. The ion-induced nucleation of sulfuric acid occurred, causing the drastic penetration of 19 nm particles through the ESP. Despite this, the overall collection efficiency was sufficient to meet the EU’s Ecodesign Directive requirements. Back corona was not detected. The optimal ESP performance is defined with further parameters: a current density of 0.5 mA/m2 at an electric field strength of about 2.7 × 105 V/m; a minimal specific collecting area of ESP (SCA) of 60 m2/(m3/s); and Nt-product of 4.5 × 1014 s/m3. Such parameters of ESPs should ensure adequate PM emissions control for any type of boiler with similar emissions characteristics. The composition of collected fly ash particles was analysed, and a method for fly ash utilisation was proposed. This research may be helpful for designing ESPs to control PM emissions for small-scale units with fossil fuel combustion.
- Open Access
- 13 November 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (22) , 15015
Long-Term Neutralization of Acidic Condensate from Gas Condensing Boilers
The pH of wastewater needs to remain between 6 and 9 to protect water organisms. Condensates from a gas condensing boiler have a pH value of about 3. An optimal way to neutralize the acid condensate is to use cheap material such as dolomite. An old-style neutralization box (NB) was tested with a standard faction of dolomite. However, it did not sufficiently neutralize the condensate. Therefore, several tests were performed involving changes to the construction of the neutralization box, a finer fraction of dolomite and aerating the condensate in the neutralization box. In summary, a new NB technology with partitions, a finer fraction of dolomite and condensate aeration proved sufficient in the neutralization of the pH of the condensate in the short and long terms. It depends on what material the heat exchanger is made of in the condensing boiler. The aluminum content reduces the effectiveness of dolomite in the long run, so aerating the condensate in the NB is recommended, which leads to its more effective neutralization.
- 13 November 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (22) , 15015
Open AccessLong-Term Neutralization of Acidic Condensate from Gas Condensing Boilers
The pH of wastewater needs to remain between 6 and 9 to protect water organisms. Condensates from a gas condensing boiler have a pH value of about 3. An optimal way to neutralize the acid condensate is to use cheap material such as dolomite. An old-style neutralization box (NB) was tested with a standard faction of dolomite. However, it did not sufficiently neutralize the condensate. Therefore, several tests were performed involving changes to the construction of the neutralization box, a finer fraction of dolomite and aerating the condensate in the neutralization box. In summary, a new NB technology with partitions, a finer fraction of dolomite and condensate aeration proved sufficient in the neutralization of the pH of the condensate in the short and long terms. It depends on what material the heat exchanger is made of in the condensing boiler. The aluminum content reduces the effectiveness of dolomite in the long run, so aerating the condensate in the NB is recommended, which leads to its more effective neutralization.
- Open Access
- 10 February 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (4) , 1610
Evaluation of Waste Blends with Sewage Sludge as a Potential Material Input for Pyrolysis
In line with the requirements of the circular economy, the European Union’s waste management legislative changes also concern the treatment of sewage sludge. Although sewage sludge production cannot be prevented, its quantities may be reduced by the synergetic effect of energy recovery via choosing a proper technology. Sewage sludge is difficult to apply as fuel alone, because of its high moisture and ash content. However, its energy use will be increased by adding suitable waste materials (different types of plastics, waste tires and paper rejects). Most recently, the thermal utilization of sewage sludge via incineration or pyrolysis has grown in importance. This article describes the fuel parameters of particular waste materials and of their blends with sewage sludge in connection with laboratory-scale thermal decomposition in an inert atmosphere, for their potential use in a semi-pilot plant pyrolysis unit. For pyrolytic application, the results of thermogravimetric analysis are needed in order to know the maximal temperature of thermal decomposition in an inert atmosphere, maximal mass losses, and weight loss rates. The samples of different thermoplastics mixed with sewage sludge, and low-density polyethylene blends with sewage sludge, had the lowest residual masses (70–74%) and the highest weight loss rates (11–19%/min). On the other hand, the blend of polyester rejects from tire processing, paper rejects and sewage sludge had the second highest residual mass (60%) and the lowest weight loss rate (3%/min).
- 10 February 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (4) , 1610
Open AccessEvaluation of Waste Blends with Sewage Sludge as a Potential Material Input for Pyrolysis
In line with the requirements of the circular economy, the European Union’s waste management legislative changes also concern the treatment of sewage sludge. Although sewage sludge production cannot be prevented, its quantities may be reduced by the synergetic effect of energy recovery via choosing a proper technology. Sewage sludge is difficult to apply as fuel alone, because of its high moisture and ash content. However, its energy use will be increased by adding suitable waste materials (different types of plastics, waste tires and paper rejects). Most recently, the thermal utilization of sewage sludge via incineration or pyrolysis has grown in importance. This article describes the fuel parameters of particular waste materials and of their blends with sewage sludge in connection with laboratory-scale thermal decomposition in an inert atmosphere, for their potential use in a semi-pilot plant pyrolysis unit. For pyrolytic application, the results of thermogravimetric analysis are needed in order to know the maximal temperature of thermal decomposition in an inert atmosphere, maximal mass losses, and weight loss rates. The samples of different thermoplastics mixed with sewage sludge, and low-density polyethylene blends with sewage sludge, had the lowest residual masses (70–74%) and the highest weight loss rates (11–19%/min). On the other hand, the blend of polyester rejects from tire processing, paper rejects and sewage sludge had the second highest residual mass (60%) and the lowest weight loss rate (3%/min).
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1745 (1) , 020012
Production of dioxins and furans for various solid fuels burnt in 25 kW automatic boiler
There has been brown coal, black coal and maize straw in a pellet form burnt in an automatic boiler. Production of dibenzodioxins and dibenzofuranes, recomputated through toxicity equivalents, expressed as the emission factor relative to the fuel unit, has differentiated in a range of ca. three orders (0.05 up to 78.9 ng/kg) in dependence on a sort of the used fuel. The measured values have been compared with emission factors used for the emission inventory in the Czech Republic and Poland and with the emission limit applicable for waste incineration plants. The study has proven the influence of chlorine content in fuel on production of dioxins and furanes.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1745 (1) , 020012
Production of dioxins and furans for various solid fuels burnt in 25 kW automatic boiler
There has been brown coal, black coal and maize straw in a pellet form burnt in an automatic boiler. Production of dibenzodioxins and dibenzofuranes, recomputated through toxicity equivalents, expressed as the emission factor relative to the fuel unit, has differentiated in a range of ca. three orders (0.05 up to 78.9 ng/kg) in dependence on a sort of the used fuel. The measured values have been compared with emission factors used for the emission inventory in the Czech Republic and Poland and with the emission limit applicable for waste incineration plants. The study has proven the influence of chlorine content in fuel on production of dioxins and furanes.