ESEhsan Mohammad Sharifi

Ehsan Mohammad Sharifi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ehsan Mohammad Sharifi has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Concurrent optimization of fracture toughness, thermal conductivity, and tribological behavior in Cf/Si3N4 composites via phase driven selection

    by Saeed Hoseinzadeh, Mohammad Reza Loghman Estarki, Ali Ghasemi, Saeed Zahabi, Gholamreza Gordani, Ehsan Mohammad Sharifi

    Carbon fiber–reinforced silicon nitride (C f /Si 3 N 4 ) composites were fabricated by spark plasma sintering (SPS) using α-, β-, and γ-Si 3 N 4 powders to clarify the influence of the initial Si 3 N 4 phase on microstructural evolution and functional properties. The results show that the starting phase significantly affects densification behavior, phase transformation, and mechanical and tribological performance. The composite derived from α-Si 3 N 4 achieved the highest relative density (96.53%) and exhibited an optimal balance of fracture toughness (10.87 MPa m 0.5 ), thermal conductivity (66 W/m K), and stable friction behavior (COF ≈ 0.46). This performance is attributed to the in-situ formation of a self-reinforced β-Si 3 N 4 microstructure during the α → β phase transformation, which promotes crack deflection, crack bridging, and effective load transfer in synergy with carbon fibers. In contrast, β- and γ-Si 3 N 4 –based composites showed lower densification or excessive hardness associated with increased porosity and secondary phase formation. These findings demonstrate that controlling the initial Si 3 N 4 phase provides an effective microstructural design strategy for developing high-performance C f /Si 3 N 4 composites for thermostructural applications such as aerospace brake discs.

  • Open Access

    The effect of amorphous Si3N4 nanoparticles and magnetized distilled water on the mechanical properties and infrared transmittance of α-Al2O3

    by Mahdi Darabi, Ehsan Mohammad Sharifi, Reza Vafaei, Akbar Eshaghi, Mohammad Reza Loghman-Estarki

    This study resolves the inherent trade-off between fracture toughness and mid-infrared transparency in α-Al2O3 ceramics. A novel shear-stress thin-layer process with magnetic-field-assisted dispersion achieves uniform distribution of 0.1 wt% amorphous Si3N4 nanoparticles and MgO/La2O3 sintering aids using 2 wt% DL dispersant at pH 10. Post-annealing at 1200 °C enhances fracture toughness by 126% (3.4 ± 0.2 to 7.68 ± 0.3 MPa m1/2) while reducing hardness from 23.6 ± 0.8 GPa to 12.6 ± 0.5 GPa, confirming improved ductility. XRD analysis verifies compressive residual stress (- 1.60 ± 0.08 GPa) and lattice strain (- 0.49 ± 0.05%). FESEM/EDS reveals grain refinement from 402 ± 18 nm to 124 ± 6 nm with homogeneity index exceeding 0.93. These microstructural modifications enable 85.3 ± 0.5% mid-infrared transmittance between 3 and 6 μm, surpassing conventional transparent alumina by 41%. This approach establishes a scalable method for designing multifunctional ceramics with simultaneous mechanical resilience and optical performance.


  • Open Access

    The Effect of Amorphous Si₃N₄ Nanoparticles and Magnetized Distilled Water on the Mechanical Properties and Infrared Transmittance of α-Al₂O₃

    by Mahdi Darabi, Ehsan Mohammad Sharifi, Reza Vafaei, Akbar Eshaghi, Mohammad Reza Loghman-Estarki

    The objective of this study was to enhance the mechanical and optical properties of α-Al2O3 ceramics through the incorporation of amorphous Si3N4 nanoparticles, in conjunction with MgO and La2O3 sintering aids. Samples were fabricated using the shear stress-thin layer (S-T) method with slurry prepared in magnetized distilled water. The effects of dispersant concentration, slurry pH, and annealing treatment were systematically examined. The material's hardness, fracture toughness, Young's modulus, and infrared transmittance were evaluated using a combination of analytical methods, including hardness and toughness tests, X-ray diffraction (XRD), infrared spectroscopy (IR), and field-emission scanning electron microscopy (FESEM). The incorporation of 0.1 wt% Si₃N₄ and 2 wt% dispersant at a pH of 10 resulted in a reduction in hardness from 23.6 GPa to 16 GPa and an enhancement in fracture toughness from 3.4 MPa·m1/2 to 6.3 MPa·m1/2. Annealing at 1200°C for 4 hours led to a significant reduction in hardness to 12.6 GPa and an enhancement in toughness to 7.7 MPa·m1/2. The Young's modulus demonstrated a decrease from 403 gigapascals (GPa) to 230 GPa, indicating a reduction in brittleness. Optical analysis demonstrated that under optimal conditions, infrared transmittance reached 85% in the 3–6 µm range.

  • Open Access

    Effect of Amorphous Si₃N₄ Nanoparticles on the Infrared Transmittance of α-Al₂O₃

    by Mahdi Darabi, Ehsan Mohammad Sharifi, Reza Vafaie, Akbar Eshaghi, Mohammad Reza Loghman Estraki

    Introduction and Objectives: This study aims to enhance the optical properties of polycrystalline alumina by controlling grain growth and minimizing structural defects. To achieve this, the influence of amorphous silicon nitride (Si₃N₄) nanoparticles as a reinforcing agent, in conjunction with MgO and La₂O₃ as sintering aids, on the infrared transmittance of PA was investigated. Furthermore, the role of the dispersing agent in improving slurry homogeneity and particle distribution was evaluated.Materials and Methods: The composite materials were synthesized via a chemical precipitation process, wherein alumina powder was mixed with Si3N4 nanoparticles, magnesium nitrate, lanthanum nitrate, and a dispersing agent in an aqueous solution.Ultrasonic waves were employed to enhance particle dispersion, and the slurry pH was adjusted to 10 to stabilize the suspension.Subsequent to powder preparation, spark plasma sintering was utilized to achieve densification and control grain growth. The microstructural and optical characteristics of the samples were then analyzed using X-ray diffraction, field emission scanning electron microscopy and infrared spectroscopy.Results: The findings indicated that the incorporation of Si3N4 nanoparticles (0.1 wt%) and a dispersing agent (2 wt%) led to an enhancement in infrared transmittance, with a maximum achieved of 85% within the 5–6 µm wavelength range. This observation was corroborated by microscopic analysis, which confirmed a reduction in grain size and an improvement in microstructural uniformity. Furthermore, X-ray diffraction analysis substantiated the preservation of the crystalline structure of alumina across all samples.Conclusion: The optimization of the sintering process, in conjunction with the incorporation of silicon nitride nanoparticles, facilitates the fabrication of transparent alumina, which exhibits augmented optical properties. These materials hold considerable promise for applications in infrared-sensitive systems, including missile guidance and optical sensor technologies.

  • Open Access

    Developing the microstructure and mechanical characteristics of 410 martensitic stainless steel during cold drawing of pipes

    by Mohmmad Mehdi Niazi, Reza Vafaei, Ehsan Mohammad Sharifi, Asghar Mahdian

    Исследовано изменение микроструктуры и механических свойств нержавеющей стали 410 (08Х13) при холодной вытяжке. Для описания процесса деформации стали при вытяжке использовали уравнение Джонсона-Кука. Методами рентгеновской дифракции совместно с FESEM и EDS анализами, а также с использованием оптической микроскопии установлено формирование деформированных и удлиненных зерен феррита с дисперсными карбидами хрома в матрице. После вытяжки предел прочности стали на растяжение увеличивается на ~ 25 % (от 770 до 960 МПа). Размер кристаллитов уменьшается от 85,6 до 58,9 нм, а их ориентация изменяется с {110} на предпочтительную {200}. Наибольший текстурный коэффициент соответствует индексам {200}. Определение значения коэффициента трения при волочении методом кольцевых образцов показало, что лучшей смазкой для волочения является раствор оксалата с горячим мылом, который обеспечивает самый низкий коэффициент трения (0,15). На основе результатов моделирования показано, что наиболее эффективный угол матрицы для волочения составляет 32 градуса, при котором наблюдается наименьшее усилие волочения 164 кН.

  • Open Access

    C.P titanium/Ti–6Al–4V joint by spark plasma welding: Microstructure and mechanical properties

    by Saeed Zahabi, Ehsan Mohammad Sharifi, Mehdi Naderi, Mazaher Ramezani, Hossein Jamali, Mohammad Reza Loghman Esatrki


  • Triethanolamine assisted sol‐gel approach for obtaining two‐dimensional magnesium aluminate nanosheets

    by E. Mohammad Sharifi, J. Shakeri, H. Sheikh, A. Alhaji, M.R. Loghman‐Estarki

    Aqueous‐phase synthetic route was applied for the preparation of magnesium aluminate spinel nanosheets with two‐dimensional nanostructure through a sol‐gel combustion approach, where triethanolamine was employed as a complexing agent and fuel. Results demonstrate that the as‐synthesized two‐dimensional nanosheets are well crystallized and show high purity. The pure magnesium aluminate nanoparticles with an average crystallite size of 25 nanometers were obtained at 1200 °C. Also, the two‐dimensional magnesium aluminate powder contain nanosheets with thicknesses in the 20 nanometers–30 nanometers range, and the lateral size is in the range of ∼10 micrometers–30 micrometers.


  • Open Access

    Effect of Chelating Agent on Morphology and Phase Evolution of Spinel Nanoparticles Synthesized via Sol-Gel Method

    by M. R. Loghman Estarki, H. Ghalibaf Tousi, E. Mohammad Sharifi, H. Sheikh, A. Alhaji

    The purpose of this study was to evaluate the effect of glycyrol (tri-dentate, GLY) and ethylenediamine (double- dentate clay, en) chelating agents on phase and morphology changes of spinel nanoparticles synthesized by sol-gel method. Characterization of samples was performed by X-ray diffraction (XRD) and field-emission scanning electron microscope (FESEM) equipped ...