Fumihito Sugai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fumihito Sugai has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Kei Okada
The University of Tokyo
4 shared publications - Kunio Kojima
The University of Tokyo, 7-3-1 Hongo
4 shared publications - Masayuki Inaba
Department of Mechano-Informatics, The University of Tokyo, Tokyo, Japan
4 shared publications - Yohei Kakiuchi
Creative Informatics, Graduate School of Information Science and Technology, The University of Tokyo, Tokyo, Japan, 113-8656
3 shared publications - Yuta Kojio
7-3-1 Hongo, Bunkyo-Ku, The University of Tokyo, Tokyo, Japan
3 shared publications Kakiuchi Yohei
Department of Mechano-Informatics, University of Tokyo, Tokyo, Japan
1 shared publication
Latest Publications
- 2 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 6 (4) , 6741-6748
Dynamic Fall Recovery Motion Generation on Biped Robot With Shell Protector
Fall recovery after falling over is a critical feature for biped robots that work in the real world. We propose a method by considering robot joint angle trajectory as a multivariable function of time and time-varying orientation of robot root links. Compared with the conventional method, our method required less time and human effort, as the joint trajectory was autonomously optimized via evolutionary search in a dynamic simulator. In addition, the gap between simulation and real-world experiments could be narrowed by adding push disturbances when performing evolutionary search in the dynamic simulator. Using the proposed method, we successfully realized the fall-recovery feature on life-sized biped robot that was equipped with shell protector CHIDORI-F as depicted in Fig.1. Combining the aforementioned fall-recovery feature and previously developed fall-tolerant robot hardware, fall detector and fall-damage-reduction motion, we realized a biped robot platform that could tolerate falling, recover from all the fallen states, and continue working for considerable time without a tether.
- 2 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 6 (4) , 6741-6748
Dynamic Fall Recovery Motion Generation on Biped Robot With Shell Protector
Fall recovery after falling over is a critical feature for biped robots that work in the real world. We propose a method by considering robot joint angle trajectory as a multivariable function of time and time-varying orientation of robot root links. Compared with the conventional method, our method required less time and human effort, as the joint trajectory was autonomously optimized via evolutionary search in a dynamic simulator. In addition, the gap between simulation and real-world experiments could be narrowed by adding push disturbances when performing evolutionary search in the dynamic simulator. Using the proposed method, we successfully realized the fall-recovery feature on life-sized biped robot that was equipped with shell protector CHIDORI-F as depicted in Fig.1. Combining the aforementioned fall-recovery feature and previously developed fall-tolerant robot hardware, fall detector and fall-damage-reduction motion, we realized a biped robot platform that could tolerate falling, recover from all the fallen states, and continue working for considerable time without a tether.
- 4 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (4) , 6419-6426
Bilateral Humanoid Teleoperation System Using Whole-Body Exoskeleton Cockpit TABLIS
In this article, we describe a system design approach for the teleoperation of a whole-body bilateral humanoid robot. The conventional approach for the teleoperation of a unilateral/bilateral humanoid robot has several problems related to bipedal locomotion. In this work, we have focused on the bipedal stability and 2D/3D locomotion space problems. Our proposed system is primarily composed of bipedal-oriented assistive subsystems and a seat-type whole-body exoskeleton cockpit called "TABLIS". The bipedal-oriented assistive subsystems prevent the humanoid from falling down in cases where an operator provides an inaccurate input. TABLIS reproduces a remote 2D/3D ground surface and overcomes the space limitation of locomotion, such as the use of treadmills. We have achieved bilateral quasi-3D step traversing using our system in a demonstration experiment.
- 4 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (4) , 6419-6426
Bilateral Humanoid Teleoperation System Using Whole-Body Exoskeleton Cockpit TABLIS
In this article, we describe a system design approach for the teleoperation of a whole-body bilateral humanoid robot. The conventional approach for the teleoperation of a unilateral/bilateral humanoid robot has several problems related to bipedal locomotion. In this work, we have focused on the bipedal stability and 2D/3D locomotion space problems. Our proposed system is primarily composed of bipedal-oriented assistive subsystems and a seat-type whole-body exoskeleton cockpit called "TABLIS". The bipedal-oriented assistive subsystems prevent the humanoid from falling down in cases where an operator provides an inaccurate input. TABLIS reproduces a remote 2D/3D ground surface and overcomes the space limitation of locomotion, such as the use of treadmills. We have achieved bilateral quasi-3D step traversing using our system in a demonstration experiment.
- 25 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (3) , 4907-4914
Footstep Modification Including Step Time and Angular Momentum Under Disturbances on Sparse Footholds
Maintaining dynamic balance is an important requirement for bipedal robots. To deal with large disturbances, the footsteps need to be modified depending on the disturbance. Currently, there are few methods that determine footsteps by considering foothold constraints and the balance of the robot. In this paper, we propose a footstep modification method that considers the steppable region. In certain situations, robots cannot maintain balance due to the limitations of the landing position on sparse footholds, such as stepping stones. Therefore, our proposed method modifies not only the step position, but also the step timing and the angular momentum, and balance can be maintained even on the footholds where the steppable region is strictly limited. These walking parameters are analytically calculated by representing the steppable region as convex hulls and applying our previously utilized method. We verified the effectiveness of the proposed method in an experiment where a life-sized humanoid robot walked on stepping stones consisting of unsteady blocks and was able to recover when pushed.
- 25 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (3) , 4907-4914
Footstep Modification Including Step Time and Angular Momentum Under Disturbances on Sparse Footholds
Maintaining dynamic balance is an important requirement for bipedal robots. To deal with large disturbances, the footsteps need to be modified depending on the disturbance. Currently, there are few methods that determine footsteps by considering foothold constraints and the balance of the robot. In this paper, we propose a footstep modification method that considers the steppable region. In certain situations, robots cannot maintain balance due to the limitations of the landing position on sparse footholds, such as stepping stones. Therefore, our proposed method modifies not only the step position, but also the step timing and the angular momentum, and balance can be maintained even on the footholds where the steppable region is strictly limited. These walking parameters are analytically calculated by representing the steppable region as convex hulls and applying our previously utilized method. We verified the effectiveness of the proposed method in an experiment where a life-sized humanoid robot walked on stepping stones consisting of unsteady blocks and was able to recover when pushed.
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (1) , 9-16
Extended Three-Dimensional Walking and Skating Motion Generation for Multiple Noncoplanar Contacts With Anisotropic Friction: Application to Walk and Skateboard and Roller Skate
In this paper, we propose a 3D walking and skating motion generation method to achieve sequential walking and skating motion with skateboard and roller skate. For generating the sequential stable skating motion using passive wheels, we must deal with non-coplanar contacts with anisotropic friction. Therefore, we use Contact Wrench Cone (CWC) for considering complex contact states and introduce the novel terminal constraints using CWC and Divergent Component of Motion (DCM) which guarantee the stability of both walking and skating motion in the 3D Center of Mass (COM) trajectory generation. Applying proposed method, the life-sized humanoid JAXON could successfully walk at 0.6 [m/s] and skate with skateboard and roller skate at 1.0 [m/s].
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (1) , 9-16
Extended Three-Dimensional Walking and Skating Motion Generation for Multiple Noncoplanar Contacts With Anisotropic Friction: Application to Walk and Skateboard and Roller Skate
In this paper, we propose a 3D walking and skating motion generation method to achieve sequential walking and skating motion with skateboard and roller skate. For generating the sequential stable skating motion using passive wheels, we must deal with non-coplanar contacts with anisotropic friction. Therefore, we use Contact Wrench Cone (CWC) for considering complex contact states and introduce the novel terminal constraints using CWC and Divergent Component of Motion (DCM) which guarantee the stability of both walking and skating motion in the 3D Center of Mass (COM) trajectory generation. Applying proposed method, the life-sized humanoid JAXON could successfully walk at 0.6 [m/s] and skate with skateboard and roller skate at 1.0 [m/s].