Kunio Kojima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Kunio Kojima has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Kei Okada
The University of Tokyo
12 shared publications - Masayuki Inaba
Department of Mechano-Informatics, The University of Tokyo, Tokyo, Japan
10 shared publications Yohei Kakiuchi
The University of Tokyo
5 shared publicationsFumihito Sugai
The University of Tokyo
4 shared publications- Fumihito Sugai
Department of Creative Informatics, The University of Tokyo, Tokyo Japan 113-8656
4 shared publications - Shintaro Noda
Research Centre for Agriculture Robotics, National Agriculture and Food Research Organization, Tsukuba, Ibaraki, Japan
4 shared publications
Latest Publications
- 19 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 858-865
Development of Adaptive-Limb Transformable Robot for Portable and Replaceable End-Effectors With Compact Lock-Spin Mechanisms
Transformable robots adapt to various environments by changing their shape or functionality. The robots are able to further expand their task range by replacing their end-effectors (EEs). In this letter, we propose an adaptive-limb transformable robot capable of replacing multiple types of mounted EEs. First, 7 degrees of freedom (DoF) limbs can reach multiple types of EEs mounted on the front body surface, and replace them using that single limb without relying on external devices. Second, we develop a compact Lock-Spin mechanism that integrates a locking mechanism into the rotor of the motor to enable continuous rotation. Experimental results demonstrate that the proposed transformable robot can replace EEs on-site and that this replacement enables locomotion and manipulation adapted to the environment.
- 19 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 858-865
Development of Adaptive-Limb Transformable Robot for Portable and Replaceable End-Effectors With Compact Lock-Spin Mechanisms
Transformable robots adapt to various environments by changing their shape or functionality. The robots are able to further expand their task range by replacing their end-effectors (EEs). In this letter, we propose an adaptive-limb transformable robot capable of replacing multiple types of mounted EEs. First, 7 degrees of freedom (DoF) limbs can reach multiple types of EEs mounted on the front body surface, and replace them using that single limb without relying on external devices. Second, we develop a compact Lock-Spin mechanism that integrates a locking mechanism into the rotor of the motor to enable continuous rotation. Experimental results demonstrate that the proposed transformable robot can replace EEs on-site and that this replacement enables locomotion and manipulation adapted to the environment.
- 16 May 2024
- Published by World Scientific Pub Co Pte Ltd in International Journal of Humanoid Robotics
- Vol. 21 (06)
Sampling-Based Global Path Planning Using Convex Polytope Approximation for Narrow Collision-Free Space of Humanoid
In this paper, we propose a computationally fast method of sampling-based global path planning for humanoids under Manifold Constraints such as closed kinematic chains and Volume-Reducing Constraints such as collision avoidance. In multi-contact and whole-body manipulation of humanoids, narrow collision-free space causes path planning to take a long computation time (narrow corridor problem). In previous research of constrained planning, Manifold Constraints are locally approximated by tangent plane, and steering motions along Manifold Constraints are found efficiently by projection or continuation methods. In this paper, we applied constrained planning algorithms to collision avoidance. Since tangent plane cannot approximate Volume-Reducing Constraints, we adopted convex polytope instead of tangent plane. Both Manifold Constraints and Volume-Reducing Constraints are locally approximated by convex polytope with linear equality and inequality constraints, and steering motions inside the convex polytope are found efficiently by the SQP-based prioritized inverse kinematics. We developed CP-KPIECE (Convex Polytope approximation-based KPIECE) with this approach. Benchmarks using the humanoid JAXON proved the effectiveness of our approach for fast path planning in narrow collision-free space of humanoids.
- 16 May 2024
- Published by World Scientific Pub Co Pte Ltd in International Journal of Humanoid Robotics
- Vol. 21 (06)
Sampling-Based Global Path Planning Using Convex Polytope Approximation for Narrow Collision-Free Space of Humanoid
In this paper, we propose a computationally fast method of sampling-based global path planning for humanoids under Manifold Constraints such as closed kinematic chains and Volume-Reducing Constraints such as collision avoidance. In multi-contact and whole-body manipulation of humanoids, narrow collision-free space causes path planning to take a long computation time (narrow corridor problem). In previous research of constrained planning, Manifold Constraints are locally approximated by tangent plane, and steering motions along Manifold Constraints are found efficiently by projection or continuation methods. In this paper, we applied constrained planning algorithms to collision avoidance. Since tangent plane cannot approximate Volume-Reducing Constraints, we adopted convex polytope instead of tangent plane. Both Manifold Constraints and Volume-Reducing Constraints are locally approximated by convex polytope with linear equality and inequality constraints, and steering motions inside the convex polytope are found efficiently by the SQP-based prioritized inverse kinematics. We developed CP-KPIECE (Convex Polytope approximation-based KPIECE) with this approach. Benchmarks using the humanoid JAXON proved the effectiveness of our approach for fast path planning in narrow collision-free space of humanoids.
- 2 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 6 (4) , 6741-6748
Dynamic Fall Recovery Motion Generation on Biped Robot With Shell Protector
Fall recovery after falling over is a critical feature for biped robots that work in the real world. We propose a method by considering robot joint angle trajectory as a multivariable function of time and time-varying orientation of robot root links. Compared with the conventional method, our method required less time and human effort, as the joint trajectory was autonomously optimized via evolutionary search in a dynamic simulator. In addition, the gap between simulation and real-world experiments could be narrowed by adding push disturbances when performing evolutionary search in the dynamic simulator. Using the proposed method, we successfully realized the fall-recovery feature on life-sized biped robot that was equipped with shell protector CHIDORI-F as depicted in Fig.1. Combining the aforementioned fall-recovery feature and previously developed fall-tolerant robot hardware, fall detector and fall-damage-reduction motion, we realized a biped robot platform that could tolerate falling, recover from all the fallen states, and continue working for considerable time without a tether.
- 2 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 6 (4) , 6741-6748
Dynamic Fall Recovery Motion Generation on Biped Robot With Shell Protector
Fall recovery after falling over is a critical feature for biped robots that work in the real world. We propose a method by considering robot joint angle trajectory as a multivariable function of time and time-varying orientation of robot root links. Compared with the conventional method, our method required less time and human effort, as the joint trajectory was autonomously optimized via evolutionary search in a dynamic simulator. In addition, the gap between simulation and real-world experiments could be narrowed by adding push disturbances when performing evolutionary search in the dynamic simulator. Using the proposed method, we successfully realized the fall-recovery feature on life-sized biped robot that was equipped with shell protector CHIDORI-F as depicted in Fig.1. Combining the aforementioned fall-recovery feature and previously developed fall-tolerant robot hardware, fall detector and fall-damage-reduction motion, we realized a biped robot platform that could tolerate falling, recover from all the fallen states, and continue working for considerable time without a tether.
- 4 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (4) , 6419-6426
Bilateral Humanoid Teleoperation System Using Whole-Body Exoskeleton Cockpit TABLIS
In this article, we describe a system design approach for the teleoperation of a whole-body bilateral humanoid robot. The conventional approach for the teleoperation of a unilateral/bilateral humanoid robot has several problems related to bipedal locomotion. In this work, we have focused on the bipedal stability and 2D/3D locomotion space problems. Our proposed system is primarily composed of bipedal-oriented assistive subsystems and a seat-type whole-body exoskeleton cockpit called "TABLIS". The bipedal-oriented assistive subsystems prevent the humanoid from falling down in cases where an operator provides an inaccurate input. TABLIS reproduces a remote 2D/3D ground surface and overcomes the space limitation of locomotion, such as the use of treadmills. We have achieved bilateral quasi-3D step traversing using our system in a demonstration experiment.
- 4 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (4) , 6419-6426
Bilateral Humanoid Teleoperation System Using Whole-Body Exoskeleton Cockpit TABLIS
In this article, we describe a system design approach for the teleoperation of a whole-body bilateral humanoid robot. The conventional approach for the teleoperation of a unilateral/bilateral humanoid robot has several problems related to bipedal locomotion. In this work, we have focused on the bipedal stability and 2D/3D locomotion space problems. Our proposed system is primarily composed of bipedal-oriented assistive subsystems and a seat-type whole-body exoskeleton cockpit called "TABLIS". The bipedal-oriented assistive subsystems prevent the humanoid from falling down in cases where an operator provides an inaccurate input. TABLIS reproduces a remote 2D/3D ground surface and overcomes the space limitation of locomotion, such as the use of treadmills. We have achieved bilateral quasi-3D step traversing using our system in a demonstration experiment.
- 25 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (3) , 4907-4914
Footstep Modification Including Step Time and Angular Momentum Under Disturbances on Sparse Footholds
Maintaining dynamic balance is an important requirement for bipedal robots. To deal with large disturbances, the footsteps need to be modified depending on the disturbance. Currently, there are few methods that determine footsteps by considering foothold constraints and the balance of the robot. In this paper, we propose a footstep modification method that considers the steppable region. In certain situations, robots cannot maintain balance due to the limitations of the landing position on sparse footholds, such as stepping stones. Therefore, our proposed method modifies not only the step position, but also the step timing and the angular momentum, and balance can be maintained even on the footholds where the steppable region is strictly limited. These walking parameters are analytically calculated by representing the steppable region as convex hulls and applying our previously utilized method. We verified the effectiveness of the proposed method in an experiment where a life-sized humanoid robot walked on stepping stones consisting of unsteady blocks and was able to recover when pushed.
- 25 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 5 (3) , 4907-4914
Footstep Modification Including Step Time and Angular Momentum Under Disturbances on Sparse Footholds
Maintaining dynamic balance is an important requirement for bipedal robots. To deal with large disturbances, the footsteps need to be modified depending on the disturbance. Currently, there are few methods that determine footsteps by considering foothold constraints and the balance of the robot. In this paper, we propose a footstep modification method that considers the steppable region. In certain situations, robots cannot maintain balance due to the limitations of the landing position on sparse footholds, such as stepping stones. Therefore, our proposed method modifies not only the step position, but also the step timing and the angular momentum, and balance can be maintained even on the footholds where the steppable region is strictly limited. These walking parameters are analytically calculated by representing the steppable region as convex hulls and applying our previously utilized method. We verified the effectiveness of the proposed method in an experiment where a life-sized humanoid robot walked on stepping stones consisting of unsteady blocks and was able to recover when pushed.
- 1 January 2020
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2020, 2A2-G16
Ukemi Motion for a Life-size Humanoid with the Air Damper Shock Absorbing Exteriors
In recent years, humanoids are expected to be used in real environments. However, humanoids are unstable and it is difficult to completely prevent falls. For this reason, it is necessary to take appropriate measures against falls that cannot be prevented. However, life-sized humanoids are large in mass and contain many fragile mechanisms, therefore they are vulnerable to impact. In this paper, we propose an exterior that uses an air damper shock absorbing exteriors that hardly restrict robot’s movement, is effective even when the robot system is stopped, and can be used for repeated falls. Furthermore, We propose a method for automatically generating Ukemi motion that make effective use of exteriors. The proposed method was applied to a life-size humanoid RHP3 and a fall experiment on a hard floor surface showed that the maximum acceleration at the time of collision could be reduced to about 40 [G].
- 1 January 2020
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2020, 2A2-G16
Ukemi Motion for a Life-size Humanoid with the Air Damper Shock Absorbing Exteriors
In recent years, humanoids are expected to be used in real environments. However, humanoids are unstable and it is difficult to completely prevent falls. For this reason, it is necessary to take appropriate measures against falls that cannot be prevented. However, life-sized humanoids are large in mass and contain many fragile mechanisms, therefore they are vulnerable to impact. In this paper, we propose an exterior that uses an air damper shock absorbing exteriors that hardly restrict robot’s movement, is effective even when the robot system is stopped, and can be used for repeated falls. Furthermore, We propose a method for automatically generating Ukemi motion that make effective use of exteriors. The proposed method was applied to a life-size humanoid RHP3 and a fall experiment on a hard floor surface showed that the maximum acceleration at the time of collision could be reduced to about 40 [G].
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 202-207
Whole-body Posture Generation by Adjusting Tool Force with CoG Movement: Application to Soil Digging
Exerting large force is one of the difficult problems for a humanoid robot. In particular, the task which needs large force with a tool or the task whose reference force is unknown such as digging are more difficult. The task of digging was realized in the previous research, but with that method the robot cannot exert large force even though force is not enough for digging because the decision method of reference shovel force is only changing the direction of the current shovel force, and modification of the robot's CoG (center of gravity) is only used for balancing. In this paper, we proposed methods to determine the reference shovel force which is necessary enough to realize the task of digging, and generate feasible posture which exerts the reference shovel force within joint torque limits. To verify the methods, we conducted experiments of the task of digging using a life-size humanoid robot JAXON. JAXON succeeded digging with some soil from soft to hard.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 202-207
Whole-body Posture Generation by Adjusting Tool Force with CoG Movement: Application to Soil Digging
Exerting large force is one of the difficult problems for a humanoid robot. In particular, the task which needs large force with a tool or the task whose reference force is unknown such as digging are more difficult. The task of digging was realized in the previous research, but with that method the robot cannot exert large force even though force is not enough for digging because the decision method of reference shovel force is only changing the direction of the current shovel force, and modification of the robot's CoG (center of gravity) is only used for balancing. In this paper, we proposed methods to determine the reference shovel force which is necessary enough to realize the task of digging, and generate feasible posture which exerts the reference shovel force within joint torque limits. To verify the methods, we conducted experiments of the task of digging using a life-size humanoid robot JAXON. JAXON succeeded digging with some soil from soft to hard.
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2019, 2A2-K10
Locomotion System Considering Foothold Information Based on Vision and Force Sense
Humanoid robots have potensials to walk on uneven ground unlike wheeled robots. However, it is difficult to reach a given destination without falling down based on only visual sensors. To reach the destination safely, we propose the autonomous safe locomotion system applying vision and sole reaction force to the footstep planning. Moreover, the robot reuses the results of the motion by saving them in the database with the foothold label given by the visual classifier. Experimental results using a real bipedal robot CHIDORI with the propsed system are shown at last.
- 1 January 2019
- Published by Japan Society of Mechanical Engineers in The Proceedings of JSME annual Conference on Robotics and Mechatronics (Robomec)
- Vol. 2019, 2A2-K10
Locomotion System Considering Foothold Information Based on Vision and Force Sense
Humanoid robots have potensials to walk on uneven ground unlike wheeled robots. However, it is difficult to reach a given destination without falling down based on only visual sensors. To reach the destination safely, we propose the autonomous safe locomotion system applying vision and sole reaction force to the footstep planning. Moreover, the robot reuses the results of the motion by saving them in the database with the foothold label given by the visual classifier. Experimental results using a real bipedal robot CHIDORI with the propsed system are shown at last.
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (1) , 9-16
Extended Three-Dimensional Walking and Skating Motion Generation for Multiple Noncoplanar Contacts With Anisotropic Friction: Application to Walk and Skateboard and Roller Skate
In this paper, we propose a 3D walking and skating motion generation method to achieve sequential walking and skating motion with skateboard and roller skate. For generating the sequential stable skating motion using passive wheels, we must deal with non-coplanar contacts with anisotropic friction. Therefore, we use Contact Wrench Cone (CWC) for considering complex contact states and introduce the novel terminal constraints using CWC and Divergent Component of Motion (DCM) which guarantee the stability of both walking and skating motion in the 3D Center of Mass (COM) trajectory generation. Applying proposed method, the life-sized humanoid JAXON could successfully walk at 0.6 [m/s] and skate with skateboard and roller skate at 1.0 [m/s].
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (1) , 9-16
Extended Three-Dimensional Walking and Skating Motion Generation for Multiple Noncoplanar Contacts With Anisotropic Friction: Application to Walk and Skateboard and Roller Skate
In this paper, we propose a 3D walking and skating motion generation method to achieve sequential walking and skating motion with skateboard and roller skate. For generating the sequential stable skating motion using passive wheels, we must deal with non-coplanar contacts with anisotropic friction. Therefore, we use Contact Wrench Cone (CWC) for considering complex contact states and introduce the novel terminal constraints using CWC and Divergent Component of Motion (DCM) which guarantee the stability of both walking and skating motion in the 3D Center of Mass (COM) trajectory generation. Applying proposed method, the life-sized humanoid JAXON could successfully walk at 0.6 [m/s] and skate with skateboard and roller skate at 1.0 [m/s].