Toshiyuki Kanakubo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Toshiyuki Kanakubo has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Helen Negash Shiferaw
Graduate School of Science and Technology, University of Tsukuba, Tsukuba 305-8573, Japan
5 shared publications - Amadou Sakhir Syll
Graduate School of Systems and Information Engineering, University of Tsukuba, Tsukuba 305-8577, Japan
3 shared publications - Hideto Sasaki
Graduate School of Science and Technology, University of Tsukuba, Tsukuba 305-8573, Japan
2 shared publications Keisuke Watanabe
Central Japan Railway Company, JR Central Towers
2 shared publications- Madappa V. R. Sivasubramanian
Department of Civil Engineering, National Institute of Technology Puducherry, Karaikal 609609, India
2 shared publications - Nobuaki Hanai
Department of Architecture, Faculty of Architecture and Civil Engineering, Kyushu Sangyo University, Fukuoka 813-8503, Japan
2 shared publications
Latest Publications
- Open Access
- 5 November 2026
- Published by Bentham Science Publishers Ltd. in The Open Construction & Building Technology Journal
- Vol. 20  (1)
Bending Performance and Evaluation of Tensile Properties of Polyester Fiber Reinforced Ductile Fiber Reinforced Cementitious Composite (PES-DFRCC)
Introduction/Objective: This study investigates the flexural and equivalent tensile behaviour of polyester fiber-reinforced ductile fiber-reinforced cementitious composite (PES-DFRCC) incorporating commercially available Indian-manufactured polyester fibers. The influence of fiber volume fraction on the flexural response and equivalent tensile properties was evaluated through four-point bending tests and inverse section analysis. This study presents the first experimental investigation of PES-DFRCC using this methodology and establishes its equivalent tensile stress–strain behaviour. Methods: Beam specimens containing different polyester fiber volume fractions were tested under four-point bending in accordance with ISO 21914:2019. Load, axial deformation, and deflection measurements were recorded, and tensile properties were determined through inverse section analysis based on the observed flexural response. Results: The PES-DFRCC specimens exhibited multiple microcracking and pronounced deflection-hardening behavior under bending. The evaluated average tensile strength ranged from 0.34 to 2.41 MPa, while the corresponding average ultimate tensile strain varied from 0.276% to 0.450%, depending on the fiber content. Discussion: The formation of multiple microcracks contributed to enhanced ductility and energy absorption capacity, indicating the effectiveness of polyester fibers in improving the post-cracking performance of cementitious composites. Conclusion: The newly developed PES-DFRCC demonstrated significant ductile behavior, characterized by multiple cracking, deflection hardening, and improved tensile performance. These findings highlight the potential of polyester fiber reinforcement for developing durable and ductile cementitious materials for structural applications.
- 5 November 2026
- Published by Bentham Science Publishers Ltd. in The Open Construction & Building Technology Journal
- Vol. 20  (1)
Open AccessBending Performance and Evaluation of Tensile Properties of Polyester Fiber Reinforced Ductile Fiber Reinforced Cementitious Composite (PES-DFRCC)
Introduction/Objective: This study investigates the flexural and equivalent tensile behaviour of polyester fiber-reinforced ductile fiber-reinforced cementitious composite (PES-DFRCC) incorporating commercially available Indian-manufactured polyester fibers. The influence of fiber volume fraction on the flexural response and equivalent tensile properties was evaluated through four-point bending tests and inverse section analysis. This study presents the first experimental investigation of PES-DFRCC using this methodology and establishes its equivalent tensile stress–strain behaviour. Methods: Beam specimens containing different polyester fiber volume fractions were tested under four-point bending in accordance with ISO 21914:2019. Load, axial deformation, and deflection measurements were recorded, and tensile properties were determined through inverse section analysis based on the observed flexural response. Results: The PES-DFRCC specimens exhibited multiple microcracking and pronounced deflection-hardening behavior under bending. The evaluated average tensile strength ranged from 0.34 to 2.41 MPa, while the corresponding average ultimate tensile strain varied from 0.276% to 0.450%, depending on the fiber content. Discussion: The formation of multiple microcracks contributed to enhanced ductility and energy absorption capacity, indicating the effectiveness of polyester fibers in improving the post-cracking performance of cementitious composites. Conclusion: The newly developed PES-DFRCC demonstrated significant ductile behavior, characterized by multiple cracking, deflection hardening, and improved tensile performance. These findings highlight the potential of polyester fiber reinforcement for developing durable and ductile cementitious materials for structural applications.
- Open Access
- 6 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Flexural behavior of fiber-reinforced cementitious composite beams reinforced with aramid rope
- 6 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessFlexural behavior of fiber-reinforced cementitious composite beams reinforced with aramid rope
- Open Access
Effect of Main Bars of Beam on Shear Strength of Beam–Column Joint in Reinforced Concrete Frame Structure
In various countries, the shear-strength design formulas for reinforced concrete beam–column joints are primarily constructed based on concrete strength, and the influence of the main bars of the beam is not explicitly reflected in these expressions. To address this limitation, this study examines the shear behavior of the joint, focusing particularly on the amount and arrangement of the main bars of the beam passing through the joint. Four beam–column joint specimens were tested under cyclic loading. The main variables of the specimens were the amount and arrangement of the main bars of the beam. The detailed strain measurements were conducted to clarify the development of bond deterioration along the main bars and the associated internal force transfer mechanisms. The experimental observations revealed significant tension-shift phenomena and progressive bond deterioration in the compression-side main bars. Within the scope of the present test series, variations in the amount and arrangement of the main bars of the beam did not significantly affect the maximum applied load. However, the indirectly evaluated joint shear force was higher in specimens with two layers in the main beam bars. Force equilibrium using force components obtained by measured strain produced even larger values at greater drift angles, indicating that joint shear assessment depends strongly on the evaluation basis. A mechanics-based diagonal strut model incorporating the internal compression field provided improved agreement with experimental results, confirming its applicability for practical design.
Open AccessEffect of Main Bars of Beam on Shear Strength of Beam–Column Joint in Reinforced Concrete Frame Structure
In various countries, the shear-strength design formulas for reinforced concrete beam–column joints are primarily constructed based on concrete strength, and the influence of the main bars of the beam is not explicitly reflected in these expressions. To address this limitation, this study examines the shear behavior of the joint, focusing particularly on the amount and arrangement of the main bars of the beam passing through the joint. Four beam–column joint specimens were tested under cyclic loading. The main variables of the specimens were the amount and arrangement of the main bars of the beam. The detailed strain measurements were conducted to clarify the development of bond deterioration along the main bars and the associated internal force transfer mechanisms. The experimental observations revealed significant tension-shift phenomena and progressive bond deterioration in the compression-side main bars. Within the scope of the present test series, variations in the amount and arrangement of the main bars of the beam did not significantly affect the maximum applied load. However, the indirectly evaluated joint shear force was higher in specimens with two layers in the main beam bars. Force equilibrium using force components obtained by measured strain produced even larger values at greater drift angles, indicating that joint shear assessment depends strongly on the evaluation basis. A mechanics-based diagonal strut model incorporating the internal compression field provided improved agreement with experimental results, confirming its applicability for practical design.
- Open Access
- 9 March 2026
- Published by MDPI AG in Preprints.org
Effect of Main Bars of Beam on Shear Strength of Beam-Column Joint in Reinforced Concrete Frame Structure
In various countries, the shear strength design formulas for reinforced concrete beam–column joints are primarily constructed based on concrete strength, and the influence of main bars of beam is not explicitly reflected in these expressions. To address this limi-tation, this study examines the shear behavior of the joint, focusing particularly on the amount and arrangement of main bars of beam passing through the joint. Four beam-column joint specimens were tested under cyclic loading. The main variables of the specimens were the amount and arrangement of the main bars of beam. The detailed strain measurements were conducted to clarify the development of bond deterioration along the main bars and the associated internal force transfer mechanisms. The ex-perimental observations revealed significant tension-shift phenomena and progressive bond deterioration in the compression-side main bars. Variations in the amount and arrangement of main bars of beam did not significantly affect the maximum applied load. However, the indirectly evaluated joint shear force was higher in specimens with two layers in beam main bars. Force equilibrium using force components obtained by measured strain produced even larger values at greater drift angles, indicating that joint shear assessment depends strongly on the evaluation basis. A mechanics-based diag-onal strut model incorporating the internal compression field provided improved agreement with experimental results, confirming its applicability for practical design.
- 9 March 2026
- Published by MDPI AG in Preprints.org
Open AccessEffect of Main Bars of Beam on Shear Strength of Beam-Column Joint in Reinforced Concrete Frame Structure
In various countries, the shear strength design formulas for reinforced concrete beam–column joints are primarily constructed based on concrete strength, and the influence of main bars of beam is not explicitly reflected in these expressions. To address this limi-tation, this study examines the shear behavior of the joint, focusing particularly on the amount and arrangement of main bars of beam passing through the joint. Four beam-column joint specimens were tested under cyclic loading. The main variables of the specimens were the amount and arrangement of the main bars of beam. The detailed strain measurements were conducted to clarify the development of bond deterioration along the main bars and the associated internal force transfer mechanisms. The ex-perimental observations revealed significant tension-shift phenomena and progressive bond deterioration in the compression-side main bars. Variations in the amount and arrangement of main bars of beam did not significantly affect the maximum applied load. However, the indirectly evaluated joint shear force was higher in specimens with two layers in beam main bars. Force equilibrium using force components obtained by measured strain produced even larger values at greater drift angles, indicating that joint shear assessment depends strongly on the evaluation basis. A mechanics-based diag-onal strut model incorporating the internal compression field provided improved agreement with experimental results, confirming its applicability for practical design.
- Open Access
Effect of Longitudinal Crack Width Variation on Bond Behavior Degradation Due to Rebar Corrosion in Reinforced Concrete
Pullout bond tests using specimens with an expansion-agent-filled pipe (EAFP) simulating the cracking due to rebar corrosion were conducted to evaluate the deterioration of bond behavior when the crack width is not uniformly distributed along the longitudinal direction. The primary specimens for the pullout test are designed with a bond length equal to 20 times the bar diameter. To investigate the distribution of bond stress along the rebar in detail, a bond analysis was performed using the local bond stress–slip model as a function of the induced crack width that is developed based on the pullout test of the specimens with a bond length of four times the rebar diameter. The EAFP simulation showed a tendency for larger crack widths at the free end, likely due to filling the expansion agent from the load-end side. From the results of the pullout bond test, as the induced crack width increases, the maximum bond stress decreases. The results of the bond analysis, assuming the five patterns of crack width distributions along the longitudinal direction, showed that the bond stress–slip curve is little affected by the difference in the crack width distribution. Within a bonded length up to 20 times the rebar diameter, the differences in crack width variations had little effect on the distribution of the local bond stress. It is possible to evaluate the bond behavior based on the average crack width.
Open AccessEffect of Longitudinal Crack Width Variation on Bond Behavior Degradation Due to Rebar Corrosion in Reinforced Concrete
Pullout bond tests using specimens with an expansion-agent-filled pipe (EAFP) simulating the cracking due to rebar corrosion were conducted to evaluate the deterioration of bond behavior when the crack width is not uniformly distributed along the longitudinal direction. The primary specimens for the pullout test are designed with a bond length equal to 20 times the bar diameter. To investigate the distribution of bond stress along the rebar in detail, a bond analysis was performed using the local bond stress–slip model as a function of the induced crack width that is developed based on the pullout test of the specimens with a bond length of four times the rebar diameter. The EAFP simulation showed a tendency for larger crack widths at the free end, likely due to filling the expansion agent from the load-end side. From the results of the pullout bond test, as the induced crack width increases, the maximum bond stress decreases. The results of the bond analysis, assuming the five patterns of crack width distributions along the longitudinal direction, showed that the bond stress–slip curve is little affected by the difference in the crack width distribution. Within a bonded length up to 20 times the rebar diameter, the differences in crack width variations had little effect on the distribution of the local bond stress. It is possible to evaluate the bond behavior based on the average crack width.
- Open Access
- 9 July 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15  (14) , 7681
Structural Performance of Fiber-Reinforced Cementitious Composite Members Reinforced with Fiber-Reinforced Polymer Bars: A Systematic Review
The integration of fiber-reinforced cementitious composites (FRCCs) with fiber-reinforced polymer (FRP) bars represents a significant advancement in concrete technology, aimed at enhancing the structural performance of reinforced concrete elements. The incorporation of fibers into cementitious composites markedly improves their mechanical properties, including tensile strength, ductility, compressive strength, and flexural strength, by effectively bridging cracks and optimizing load distribution. Furthermore, FRP bars extend these properties with their high tensile strength, lightweight characteristics, and exceptional corrosion resistance, rendering them ideal for applications in aggressive environments. In recent years, there has been a notable increase in interest from the engineering research community regarding this topic, primarily to solve the issues of aging and deteriorating infrastructure. Researchers have conducted extensive investigations into the structural performance of FRCC and FRP composite systems. This paper presents a systematic literature review that surveys experimental and analytical studies, findings, and emerging trends in this field. A comprehensive search on the Web of Science identified 40 relevant research articles through a rigorous selection process. Key factors of structural performance, such as bond behavior, flexural behavior, ductility performance assessments, shear and torsional performance, and durability evaluations, have been documented. This review aims to provide an in-depth understanding of the structural performance of these innovative composite materials, paving the way for future research and development in construction materials technology.
- 9 July 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15  (14) , 7681
Open AccessStructural Performance of Fiber-Reinforced Cementitious Composite Members Reinforced with Fiber-Reinforced Polymer Bars: A Systematic Review
The integration of fiber-reinforced cementitious composites (FRCCs) with fiber-reinforced polymer (FRP) bars represents a significant advancement in concrete technology, aimed at enhancing the structural performance of reinforced concrete elements. The incorporation of fibers into cementitious composites markedly improves their mechanical properties, including tensile strength, ductility, compressive strength, and flexural strength, by effectively bridging cracks and optimizing load distribution. Furthermore, FRP bars extend these properties with their high tensile strength, lightweight characteristics, and exceptional corrosion resistance, rendering them ideal for applications in aggressive environments. In recent years, there has been a notable increase in interest from the engineering research community regarding this topic, primarily to solve the issues of aging and deteriorating infrastructure. Researchers have conducted extensive investigations into the structural performance of FRCC and FRP composite systems. This paper presents a systematic literature review that surveys experimental and analytical studies, findings, and emerging trends in this field. A comprehensive search on the Web of Science identified 40 relevant research articles through a rigorous selection process. Key factors of structural performance, such as bond behavior, flexural behavior, ductility performance assessments, shear and torsional performance, and durability evaluations, have been documented. This review aims to provide an in-depth understanding of the structural performance of these innovative composite materials, paving the way for future research and development in construction materials technology.
- Open Access
Verification of Crack Width Evaluation in Fiber-Reinforced Cementitious Composite Reinforced with Various Types of Fiber-Reinforced Polymer Bars
This study aims to verify the adaptability of a crack width evaluation method for fiber-reinforced cementitious composite (FRCC) proposed by the authors to various combinations of fiber-reinforced polymer (FRP) bars and FRCCs. As this evaluation method requires bond constitutive laws between FRP bars and FRCC, bond tests between FRP and FRCCs were conducted. The FRP and FRCC combinations used in the bond tests were spiral-type CFRP and GFRP bars with PVA-FRCC, as well as strand-type CFRP bars with aramid–FRCC. The maximum bond stress tended to increase as the rib–height ratio of the spiral-type bars increased. When the rib–height ratio increased by 50%, the maximum bond stress of the CFRP and GFRP bars increased by 11% and 33%, respectively. For aramid–FRCC, the average maximum bond stress in the FRCC with a 0.25% volume fraction was 1.67 times that in mortar, and that in 0.50% was 2.01 times that in mortar. The bond constitutive laws were modeled using the trilinear model. Verifications of the method’s adaptability were conducted using tension tests on prisms made of spiral-type CFRP and GFRP bars with PVA-FRCC. As a result of the tension tests, when the FRP strain reached approximately 0.3%, the crack width was about 0.2 mm for CFRP bars and about 0.1 mm for GFRP bars. Verifications were also conducted using four-point bending tests on strand-type CFRP bar beams with aramid–FRCC. The crack width at the same FRP strain tended to become smaller as the fiber volume fraction of FRCC increased. When the FRP strain reached approximately 0.2%, the average crack width of the mortar specimen was around 0.25 mm, whereas it was about 0.15 mm in FRCC with a 0.25% volume fraction and about 0.10 mm at 0.5%. The test results for FRP strain versus crack width relationships were compared with the calculations using the crack width prediction formula. The test results and calculation results were in good agreement.
Open AccessVerification of Crack Width Evaluation in Fiber-Reinforced Cementitious Composite Reinforced with Various Types of Fiber-Reinforced Polymer Bars
This study aims to verify the adaptability of a crack width evaluation method for fiber-reinforced cementitious composite (FRCC) proposed by the authors to various combinations of fiber-reinforced polymer (FRP) bars and FRCCs. As this evaluation method requires bond constitutive laws between FRP bars and FRCC, bond tests between FRP and FRCCs were conducted. The FRP and FRCC combinations used in the bond tests were spiral-type CFRP and GFRP bars with PVA-FRCC, as well as strand-type CFRP bars with aramid–FRCC. The maximum bond stress tended to increase as the rib–height ratio of the spiral-type bars increased. When the rib–height ratio increased by 50%, the maximum bond stress of the CFRP and GFRP bars increased by 11% and 33%, respectively. For aramid–FRCC, the average maximum bond stress in the FRCC with a 0.25% volume fraction was 1.67 times that in mortar, and that in 0.50% was 2.01 times that in mortar. The bond constitutive laws were modeled using the trilinear model. Verifications of the method’s adaptability were conducted using tension tests on prisms made of spiral-type CFRP and GFRP bars with PVA-FRCC. As a result of the tension tests, when the FRP strain reached approximately 0.3%, the crack width was about 0.2 mm for CFRP bars and about 0.1 mm for GFRP bars. Verifications were also conducted using four-point bending tests on strand-type CFRP bar beams with aramid–FRCC. The crack width at the same FRP strain tended to become smaller as the fiber volume fraction of FRCC increased. When the FRP strain reached approximately 0.2%, the average crack width of the mortar specimen was around 0.25 mm, whereas it was about 0.15 mm in FRCC with a 0.25% volume fraction and about 0.10 mm at 0.5%. The test results for FRP strain versus crack width relationships were compared with the calculations using the crack width prediction formula. The test results and calculation results were in good agreement.
- Open Access
- 16 September 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8  (9) , 361
Bridging Behavior of Palm Fiber in Cementitious Composite
This study addresses the growing need for sustainable construction materials by investigating the mechanical properties and behavior of palm fiber-reinforced cementitious composite (FRCC), a potential eco-friendly alternative to synthetic fiber reinforcements. Despite the promise of natural fibers in enhancing the mechanical performance of composites, challenges remain in optimizing fiber distribution, fiber–composite bonding mechanism, and its balance to matrix strength. To address these challenges, this study conducted extensive experimental programs using palm fiber as reinforcement, focusing on understanding the fiber–matrix interaction, determining the pullout load–slip relationship, and modeling fiber bridging behavior. The experimental program included density calculations and scanning electron microscope (SEM) analysis to examine the surface morphology and diameter of the fibers. Single fiber pullout tests were performed under varying conditions to assess the pullout load, slip behavior, and failure modes of the palm fiber, and a relationship between the pullout load and slip with the embedded length of the palm fiber was constructed. A trilinear model was developed to describe the pullout load–slip behavior of single fibers, and a corresponding palm-FRCC bridging model was constructed using the results from these tests. Section analysis was conducted to assess the adaptability of the modeled bridging law calculations, and the analysis result of the bending moment–curvature relationship shows a good agreement with the experimental results obtained from the four-point bending test of palm-FRCC. These findings demonstrate the potential of palm fibers in improving the mechanical performance of FRCC and contribute to the broader understanding of natural fiber reinforcement in cementitious composites.
- 16 September 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8  (9) , 361
Open AccessBridging Behavior of Palm Fiber in Cementitious Composite
This study addresses the growing need for sustainable construction materials by investigating the mechanical properties and behavior of palm fiber-reinforced cementitious composite (FRCC), a potential eco-friendly alternative to synthetic fiber reinforcements. Despite the promise of natural fibers in enhancing the mechanical performance of composites, challenges remain in optimizing fiber distribution, fiber–composite bonding mechanism, and its balance to matrix strength. To address these challenges, this study conducted extensive experimental programs using palm fiber as reinforcement, focusing on understanding the fiber–matrix interaction, determining the pullout load–slip relationship, and modeling fiber bridging behavior. The experimental program included density calculations and scanning electron microscope (SEM) analysis to examine the surface morphology and diameter of the fibers. Single fiber pullout tests were performed under varying conditions to assess the pullout load, slip behavior, and failure modes of the palm fiber, and a relationship between the pullout load and slip with the embedded length of the palm fiber was constructed. A trilinear model was developed to describe the pullout load–slip behavior of single fibers, and a corresponding palm-FRCC bridging model was constructed using the results from these tests. Section analysis was conducted to assess the adaptability of the modeled bridging law calculations, and the analysis result of the bending moment–curvature relationship shows a good agreement with the experimental results obtained from the four-point bending test of palm-FRCC. These findings demonstrate the potential of palm fibers in improving the mechanical performance of FRCC and contribute to the broader understanding of natural fiber reinforcement in cementitious composites.
- Open Access
Influence of Fiber Dimensions on Bridging Performance of Polyvinyl Alcohol Fiber-Reinforced Cementitious Composite (PVA-FRCC)
This study investigates the influence of fiber dimensions on the bridging performance of polyvinyl alcohol fiber-reinforced cementitious composite (PVA-FRCC) through an experimental and analytical program. Bending tests, bridging law calculations, and section analysis are conducted. Bending tests of notched specimens of PVA-FRCC with six different PVA fiber dimensions are performed to determine the load–deflection (LPD) and bending moment–crack mouth opening displacement (CMOD) relationships. The fiber volume fraction for all PVA-FRCCs is set to 2%. It is found that the load capacity of PVA-FRCC with a 27 μm diameter fiber is much higher than that of the other fibers, and the load capacity decreases as the fiber diameter increases. The study proposes parameters for the characteristic points of the tri-linear model for the single-fiber pullout model as functions of diameter, bond fracture energy, elastic modulus, cross-sectional area, and perimeter of the fiber. These findings provide valuable insights into the behavior of PVA-FRCC under different fiber dimensions. Bridging law calculations are conducted to obtain tensile stress–crack width relationships using the developed single-fiber pullout models. The Popovics model for the complete tensile stress–crack width relationship is adopted to obtain a better fit with the bridging law calculation, and then section analysis is conducted. The bridging law calculation results show that the maximum tensile stress decreases as the fiber diameter increases. It is also determined that most of the smaller-diameter fibers ruptured, whereas the larger fiber diameters pulled out from the matrix. The section analysis results show good agreement with the maximum bending moments obtained from the bending test.
Open AccessInfluence of Fiber Dimensions on Bridging Performance of Polyvinyl Alcohol Fiber-Reinforced Cementitious Composite (PVA-FRCC)
This study investigates the influence of fiber dimensions on the bridging performance of polyvinyl alcohol fiber-reinforced cementitious composite (PVA-FRCC) through an experimental and analytical program. Bending tests, bridging law calculations, and section analysis are conducted. Bending tests of notched specimens of PVA-FRCC with six different PVA fiber dimensions are performed to determine the load–deflection (LPD) and bending moment–crack mouth opening displacement (CMOD) relationships. The fiber volume fraction for all PVA-FRCCs is set to 2%. It is found that the load capacity of PVA-FRCC with a 27 μm diameter fiber is much higher than that of the other fibers, and the load capacity decreases as the fiber diameter increases. The study proposes parameters for the characteristic points of the tri-linear model for the single-fiber pullout model as functions of diameter, bond fracture energy, elastic modulus, cross-sectional area, and perimeter of the fiber. These findings provide valuable insights into the behavior of PVA-FRCC under different fiber dimensions. Bridging law calculations are conducted to obtain tensile stress–crack width relationships using the developed single-fiber pullout models. The Popovics model for the complete tensile stress–crack width relationship is adopted to obtain a better fit with the bridging law calculation, and then section analysis is conducted. The bridging law calculation results show that the maximum tensile stress decreases as the fiber diameter increases. It is also determined that most of the smaller-diameter fibers ruptured, whereas the larger fiber diameters pulled out from the matrix. The section analysis results show good agreement with the maximum bending moments obtained from the bending test.
- Open Access
Bond and Cracking Characteristics of PVA-Fiber-Reinforced Cementitious Composite Reinforced with Braided AFRP Bars
Easy maintenance and high durability are expected in structures made with fiber-reinforced cementitious composite (FRCC) reinforced with fiber-reinforced polymer (FRP) bars. In this study, we focused on the bond and cracking characteristics of polyvinyl alcohol (PVA)-FRCC reinforced with braided AFRP bars (AFRP/PVA-FRCC). Pullout tests on specimens with varying bond lengths were conducted. Beam specimens were also subjected to four-point bending tests. In the pullout tests, experimental parameters included the cross-sectional dimensions and the fiber volume fractions of PVA-FRCC. A trilinear model for the bond constitutive law (bond stress–loaded-end slip relationship) was proposed. In the pullout bond test with specimens of long bond length, bond strength was found to increase with increases in both the fiber volume fraction and the cross-sectional dimension of the specimens. Bond behavior in specimens of long bond length was analyzed numerically using the proposed bond constitutive law. The calculated average bond stress–loaded-end slip relationships favorably fitted the test results. In bending tests with AFRP/PVA-FRCC beam specimens, high ductility was indicated by the bridging effect of fibers. The number of cracks increased with increases in the fiber volume fraction of PVA-FRCC. In specimens with a fiber volume fraction of 2%, the load reached its maximum value due to compression fracture of the FRCC. The crack width in PVA-FRCC calculated by the predicted formula, considering the bond constitutive law and the fiber bridging law, showed good agreement with the reinforcement strain–crack width relationship obtained from the tests.
Open AccessBond and Cracking Characteristics of PVA-Fiber-Reinforced Cementitious Composite Reinforced with Braided AFRP Bars
Easy maintenance and high durability are expected in structures made with fiber-reinforced cementitious composite (FRCC) reinforced with fiber-reinforced polymer (FRP) bars. In this study, we focused on the bond and cracking characteristics of polyvinyl alcohol (PVA)-FRCC reinforced with braided AFRP bars (AFRP/PVA-FRCC). Pullout tests on specimens with varying bond lengths were conducted. Beam specimens were also subjected to four-point bending tests. In the pullout tests, experimental parameters included the cross-sectional dimensions and the fiber volume fractions of PVA-FRCC. A trilinear model for the bond constitutive law (bond stress–loaded-end slip relationship) was proposed. In the pullout bond test with specimens of long bond length, bond strength was found to increase with increases in both the fiber volume fraction and the cross-sectional dimension of the specimens. Bond behavior in specimens of long bond length was analyzed numerically using the proposed bond constitutive law. The calculated average bond stress–loaded-end slip relationships favorably fitted the test results. In bending tests with AFRP/PVA-FRCC beam specimens, high ductility was indicated by the bridging effect of fibers. The number of cracks increased with increases in the fiber volume fraction of PVA-FRCC. In specimens with a fiber volume fraction of 2%, the load reached its maximum value due to compression fracture of the FRCC. The crack width in PVA-FRCC calculated by the predicted formula, considering the bond constitutive law and the fiber bridging law, showed good agreement with the reinforcement strain–crack width relationship obtained from the tests.