Ruimin Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ruimin Xu has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Bo Yan
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu 611731, China
6 shared publications - Yuehang Xu
University of Electronic Science and Technology of China
5 shared publications - Yong Zhang
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
4 shared publications - Chengkai Wu
School of Electronic Science and Engineering University of Electronic Science and Technology of China Chengdu China
3 shared publications - Chris Mi
Department of Electrical and Computer Engineering, San Diego State University, San Diego, CA 92182, USA
3 shared publications - Jia-Qi Zhu
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, 12599 Chengdu, Sichuan China 611731
3 shared publications
Latest Publications
- Open Access
Terahertz Metamaterial Waveguide with I-Shaped Resonators for Phase and Absorption Modulation
In terahertz communication systems, amplifiers and other components can induce non-linear distortion in terms of amplitude and phase, resulting in system performance degradation. This paper presents a terahertz metamaterial waveguide to mitigate amplitude and phase distortions in some terahertz systems. A simple method based on free-space analysis is proposed for designing metamaterial waveguides in an enclosed space. The quasi-periodic metamaterial structures, which feature I-shaped resonant patterns, are integrated onto the inner walls of rectangular waveguides. The phase and amplitude of electromagnetic waves within the waveguide can be modulated by varying the dimensions and number of these resonators. Utilizing the effective medium theory and the equivalent circuits, the metamaterial waveguide’s phase and absorption modulation mechanisms are analyzed. Based on the proposed structure, a metamaterial waveguide with I-shaped resonators is designed and fabricated, and its abilities to modulate the phase and absorption of terahertz waves around 0.2 THz are demonstrated.
Open AccessTerahertz Metamaterial Waveguide with I-Shaped Resonators for Phase and Absorption Modulation
In terahertz communication systems, amplifiers and other components can induce non-linear distortion in terms of amplitude and phase, resulting in system performance degradation. This paper presents a terahertz metamaterial waveguide to mitigate amplitude and phase distortions in some terahertz systems. A simple method based on free-space analysis is proposed for designing metamaterial waveguides in an enclosed space. The quasi-periodic metamaterial structures, which feature I-shaped resonant patterns, are integrated onto the inner walls of rectangular waveguides. The phase and amplitude of electromagnetic waves within the waveguide can be modulated by varying the dimensions and number of these resonators. Utilizing the effective medium theory and the equivalent circuits, the metamaterial waveguide’s phase and absorption modulation mechanisms are analyzed. Based on the proposed structure, a metamaterial waveguide with I-shaped resonators is designed and fabricated, and its abilities to modulate the phase and absorption of terahertz waves around 0.2 THz are demonstrated.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (9) , 1349-1352
A 194–214-GHz Single-Sideband Mixer With Vertical and Inline Transitions Suitable for Linear Array Applications
A 194–214-GHz single-sideband (SSB) Schottky diode-based subharmonic mixer is newly presented for linear array applications. To realize 3-D integration, a vertical transition is adopted, which also acts as an IF-LO duplexer and an impedance transformer. A waveguide filter is integrated into the mixer for high image rejection, and an inline transition performs efficient mode conversion and impedance matching between the waveguide filter and the diode. The proposed mixer is more suitable for repeated arrangement in a linear array than conventional mixers with orthogonal configuration. A four-element mixer array is fabricated and measured. The array’s minimum SSB conversion loss (CL) is 8.1–10.4 dB from 194 to 214 GHz, the CL difference between elements is less than 1.3 dB, and the sideband rejection ratio is better than 30 dBc.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (9) , 1349-1352
A 194–214-GHz Single-Sideband Mixer With Vertical and Inline Transitions Suitable for Linear Array Applications
A 194–214-GHz single-sideband (SSB) Schottky diode-based subharmonic mixer is newly presented for linear array applications. To realize 3-D integration, a vertical transition is adopted, which also acts as an IF-LO duplexer and an impedance transformer. A waveguide filter is integrated into the mixer for high image rejection, and an inline transition performs efficient mode conversion and impedance matching between the waveguide filter and the diode. The proposed mixer is more suitable for repeated arrangement in a linear array than conventional mixers with orthogonal configuration. A four-element mixer array is fabricated and measured. The array’s minimum SSB conversion loss (CL) is 8.1–10.4 dB from 194 to 214 GHz, the CL difference between elements is less than 1.3 dB, and the sideband rejection ratio is better than 30 dBc.
- Open Access
- 20 January 2021
- Published by MDPI AG in Electronics
- Vol. 10 (3) , 234
A 560 GHz Sub-Harmonic Mixer Using Half-Global Design Method
In this paper, a 560 GHz terahertz sub-harmonic mixer using a new half-global design method is reported. This method combines the advantages of the subdivision design method and the global design method, and greatly enhances the abilities of the optimization of matching variables while retaining the portability of the unit circuit. When the local oscillator (LO) frequency was fixed with 3 mW power at 280 GHz, average up-conversion double sideband (DSB) conversion loss of 8 dB with intermediate frequency (IF) power of −5 dBm was achieved.
- 20 January 2021
- Published by MDPI AG in Electronics
- Vol. 10 (3) , 234
Open AccessA 560 GHz Sub-Harmonic Mixer Using Half-Global Design Method
In this paper, a 560 GHz terahertz sub-harmonic mixer using a new half-global design method is reported. This method combines the advantages of the subdivision design method and the global design method, and greatly enhances the abilities of the optimization of matching variables while retaining the portability of the unit circuit. When the local oscillator (LO) frequency was fixed with 3 mW power at 280 GHz, average up-conversion double sideband (DSB) conversion loss of 8 dB with intermediate frequency (IF) power of −5 dBm was achieved.
- 10 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (2) , 1295-1304
Millimeter-Wave Waveguide-to-Microstrip Transition With a Built-In DC/IF Return Path
In this article, a novel waveguide-to-microstrip transition with a built-in dc/IF return path is proposed, in which a traditional E-plane probe is directly connected to the backshort by a thin metal wire along the axis of the waveguide. The proposed waveguide-to-microstrip transition implements an additional dc/IF return path while realizing mode conversion. Moreover, the presence of the dc/IF return path has little influence on the performance of the original E-plane probe. The operating principle is analyzed by theoretical analysis and full-wave simulation, and the design procedure of the transition is also presented. To implement the proposed dc/IF return path on different substrates, two approaches, including direct integration with planar circuits or with wire bonding technology, are developed. Furthermore, two back-to-back transition prototypes working in the millimeter and submillimeter bands were designed and characterized. The measured results are in excellent agreement with the simulations. Finally, as an application example, a 70-/140-GHz unbalanced frequency doubler adopting this structure for both dc biasing and dc grounding was designed and fabricated. Measured results show that the conversion loss of the fabricated doubler is less than 13 dB in the range from 125 to 145 GHz, and the minimum conversion loss is 11 dB at 140 GHz with 100-mW input power.
- 10 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (2) , 1295-1304
Millimeter-Wave Waveguide-to-Microstrip Transition With a Built-In DC/IF Return Path
In this article, a novel waveguide-to-microstrip transition with a built-in dc/IF return path is proposed, in which a traditional E-plane probe is directly connected to the backshort by a thin metal wire along the axis of the waveguide. The proposed waveguide-to-microstrip transition implements an additional dc/IF return path while realizing mode conversion. Moreover, the presence of the dc/IF return path has little influence on the performance of the original E-plane probe. The operating principle is analyzed by theoretical analysis and full-wave simulation, and the design procedure of the transition is also presented. To implement the proposed dc/IF return path on different substrates, two approaches, including direct integration with planar circuits or with wire bonding technology, are developed. Furthermore, two back-to-back transition prototypes working in the millimeter and submillimeter bands were designed and characterized. The measured results are in excellent agreement with the simulations. Finally, as an application example, a 70-/140-GHz unbalanced frequency doubler adopting this structure for both dc biasing and dc grounding was designed and fabricated. Measured results show that the conversion loss of the fabricated doubler is less than 13 dB in the range from 125 to 145 GHz, and the minimum conversion loss is 11 dB at 140 GHz with 100-mW input power.
- 6 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (6) , 6323-6338
An NFC-Connected Coupler Using IPT-CPT-Combined Wireless Charging for Metal-Cover Smartphone Applications
An NFC-connected coupler using IPT-CPT-combined wireless charging is proposed for metal-cover smartphone applications. To mitigate eddy current loss in the metal cover, capacitive power transfer (CPT) is introduced. Compared with traditional CPT, wireless power transfer through a metal cover is realized, and cost and valuable space inside the smartphone are saved. To achieve CPT through a metal cover, the metal cover itself is separated by a cross-slot and utilized as receiving plates. To reduce the voltage across the metal cover within a safety range, inductive power transfer (IPT) is applied. The already-existed near field communication (NFC) antenna is firstly used as the receiving coil for IPT and also performs as the compensated inductance for CPT. By connecting one of its feed lines to the metal cover, only a parallel external capacitor is needed to construct the receiver of the proposed coupler because the metal cover and NFC antenna are components that already exist inside the smartphone, which greatly saves space inside the smartphone and cost for the proposed coupler. Prototypes of the proposed NFC-connected coupler with and without actual smartphone have been built. The wireless power transfer through metal cover by IPT and CPT has been validated via experiment.
- 6 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (6) , 6323-6338
An NFC-Connected Coupler Using IPT-CPT-Combined Wireless Charging for Metal-Cover Smartphone Applications
An NFC-connected coupler using IPT-CPT-combined wireless charging is proposed for metal-cover smartphone applications. To mitigate eddy current loss in the metal cover, capacitive power transfer (CPT) is introduced. Compared with traditional CPT, wireless power transfer through a metal cover is realized, and cost and valuable space inside the smartphone are saved. To achieve CPT through a metal cover, the metal cover itself is separated by a cross-slot and utilized as receiving plates. To reduce the voltage across the metal cover within a safety range, inductive power transfer (IPT) is applied. The already-existed near field communication (NFC) antenna is firstly used as the receiving coil for IPT and also performs as the compensated inductance for CPT. By connecting one of its feed lines to the metal cover, only a parallel external capacitor is needed to construct the receiver of the proposed coupler because the metal cover and NFC antenna are components that already exist inside the smartphone, which greatly saves space inside the smartphone and cost for the proposed coupler. Prototypes of the proposed NFC-connected coupler with and without actual smartphone have been built. The wireless power transfer through metal cover by IPT and CPT has been validated via experiment.
- 30 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (12) , 2433-2436
Integrated Dipole Antenna With Bandwidth Enhancement for Terahertz Waveguide-to-CPWG Transition
In this letter, a broadband waveguide-to-coplanar waveguide with ground (CPWG) transition for large-chip-width substrate operating within terahertz frequencies is demonstrated. This transition adopts an integrated dipole antenna with coupling branches and disks topology. This compact transition reduces parasitic effects by wire-bonding and is suitable for direct integration with terahertz monolithic integrated circuits (TMICs), and it enables low energy conversion loss over a wide frequency band. The transition was fabricated on a 970 μm-width substrate by the 50 μm-thick InP technology and designed for WR-4.3 standard waveguide (546 μm width). The measured results show that the bandwidth with 1 dB insertion loss per antenna is as wide as 80 GHz, and the in-band return loss is better than 10 dB.
- 30 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (12) , 2433-2436
Integrated Dipole Antenna With Bandwidth Enhancement for Terahertz Waveguide-to-CPWG Transition
In this letter, a broadband waveguide-to-coplanar waveguide with ground (CPWG) transition for large-chip-width substrate operating within terahertz frequencies is demonstrated. This transition adopts an integrated dipole antenna with coupling branches and disks topology. This compact transition reduces parasitic effects by wire-bonding and is suitable for direct integration with terahertz monolithic integrated circuits (TMICs), and it enables low energy conversion loss over a wide frequency band. The transition was fabricated on a 970 μm-width substrate by the 50 μm-thick InP technology and designed for WR-4.3 standard waveguide (546 μm width). The measured results show that the bandwidth with 1 dB insertion loss per antenna is as wide as 80 GHz, and the in-band return loss is better than 10 dB.
- 16 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (3) , 3758-3769
An NFC-CPT-Combined Coupler With Series- None Compensation for Metal-Cover Smartphone Applications
An NFC-CPT-combined coupler with a series-none compensation topology is proposed for metal-cover smartphone applications. To achieve capacitive power transfer through metal cover, the metal cover itself is used as receiving metal plates. To realize near field communication (NFC) through metal cover, the cross slot including a slim horizontal slot and a rectangular slot is embedded on the metal cover, which mitigates the eddy current loss and increases the inductive coupling for the NFC antenna. Besides, the cross slot divides the metal cover into two separate metal plates, which is necessary for capacitive power transfer. Considering the space limitation and safety requirement, no compensation components are integrated inside the smartphone and only a series inductance is integrated on the transmitter side. A prototype of the proposed NFC-CPT-combined coupler has been built. The wireless power transfer and NFC through metalcover have been validated via experiment. The experimental results show that the prototype achieves 5 W output power with a 93.5 % circuit efficiency at 6.78 MHz, and the detection range of the NFC antenna is 61 mm.
- 16 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (3) , 3758-3769
An NFC-CPT-Combined Coupler With Series- None Compensation for Metal-Cover Smartphone Applications
An NFC-CPT-combined coupler with a series-none compensation topology is proposed for metal-cover smartphone applications. To achieve capacitive power transfer through metal cover, the metal cover itself is used as receiving metal plates. To realize near field communication (NFC) through metal cover, the cross slot including a slim horizontal slot and a rectangular slot is embedded on the metal cover, which mitigates the eddy current loss and increases the inductive coupling for the NFC antenna. Besides, the cross slot divides the metal cover into two separate metal plates, which is necessary for capacitive power transfer. Considering the space limitation and safety requirement, no compensation components are integrated inside the smartphone and only a series inductance is integrated on the transmitter side. A prototype of the proposed NFC-CPT-combined coupler has been built. The wireless power transfer and NFC through metalcover have been validated via experiment. The experimental results show that the prototype achieves 5 W output power with a 93.5 % circuit efficiency at 6.78 MHz, and the detection range of the NFC antenna is 61 mm.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (5) , 4847-4858
Three-Coil Wireless Charging System for Metal-Cover Smartphone Applications
A three-coil wireless charging system is proposed for full metal-cover smartphone applications. Considering the space limitation and other antennas in the smartphone, the receiver coil embedded in the smartphone is designed to be miniaturized as 16 mm × 65 mm. By integrating a series capacitance at the end of the 2 mm width narrow horizontal slot loading on the metal cover, the metal cover is converted to a relay coil of the three-coil system and wireless power transfer through the metal cover is thus achieved. A prototype of the proposed three-coil system has been built and wireless power transfer through metal cover has been validated via experiment. The experimental results show that the prototype achieves 5 W output power with 71% coil-to-coil efficiency.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (5) , 4847-4858
Three-Coil Wireless Charging System for Metal-Cover Smartphone Applications
A three-coil wireless charging system is proposed for full metal-cover smartphone applications. Considering the space limitation and other antennas in the smartphone, the receiver coil embedded in the smartphone is designed to be miniaturized as 16 mm × 65 mm. By integrating a series capacitance at the end of the 2 mm width narrow horizontal slot loading on the metal cover, the metal cover is converted to a relay coil of the three-coil system and wireless power transfer through the metal cover is thus achieved. A prototype of the proposed three-coil system has been built and wireless power transfer through metal cover has been validated via experiment. The experimental results show that the prototype achieves 5 W output power with 71% coil-to-coil efficiency.
- 22 May 2019
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 33 (3) , e2622
A one‐port automatic fixture removal method for de‐embedding
Traditional calibration methods and measurement‐based de‐embedding processes require the design of calibration kits and measurement standards, and the processes are cumbersome and costly. Even the simple automatic fixture removal (AFR) with 2x‐through fixtures still needs a through line to extract the fixtures' characteristics, and there are some restrictions. With one‐port AFR (1xAFR), the open fixture's time domain response (TDR) could be gated and windowed, then extracted to fixture's through S‐parameter. When the fixture is connected to device under test (DUT), its response could be de‐embedded from the blended S‐parameter and the DUT's S‐parameter could be obtained. In this paper, the basic principle and extraction process of 1xAFR are described, and two measurement cases are demonstrated to verify 1xAFR's ease of use and accuracy.
- 22 May 2019
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 33 (3) , e2622
A one‐port automatic fixture removal method for de‐embedding
Traditional calibration methods and measurement‐based de‐embedding processes require the design of calibration kits and measurement standards, and the processes are cumbersome and costly. Even the simple automatic fixture removal (AFR) with 2x‐through fixtures still needs a through line to extract the fixtures' characteristics, and there are some restrictions. With one‐port AFR (1xAFR), the open fixture's time domain response (TDR) could be gated and windowed, then extracted to fixture's through S‐parameter. When the fixture is connected to device under test (DUT), its response could be de‐embedded from the blended S‐parameter and the DUT's S‐parameter could be obtained. In this paper, the basic principle and extraction process of 1xAFR are described, and two measurement cases are demonstrated to verify 1xAFR's ease of use and accuracy.
- Open Access
- 25 April 2019
- Published by MDPI AG in Micromachines
- Vol. 10 (4) , 277
A 135-190 GHz Broadband Self-Biased Frequency Doubler using Four-Anode Schottky Diodes
This paper describes the design and demonstration of a 135–190 GHz self-biased broadband frequency doubler based on planar Schottky diodes. Unlike traditional bias schemes, the diodes are biased in resistive mode by a self-bias resistor; thus, no additional bias voltage is needed for the doubler. The Schottky diodes in this verification are micron-scaled devices with an anode area of 6.6 μm2 and an epitaxial layer thickness of 0.26 μm. For accurate design of the doubler, the 3D-EM model of the Schottky diode is built up to extract the parasitic parameters induced by the diode package when frequency rises up to the terahertz band. In order to implement broadband working, input waveguide steps, output suspended microstrip steps, and output probe with bias filter are all used as matching elements for impedance matching. Measured results show that the doubler exhibits a 3 dB bandwidth of 34% from 135 GHz to 190 GHz, with a conversion efficiency of above 4% when supplied with 100 mW of input power. A 17.8 mW peak output power with a 10.2% efficiency was measured at 166 GHz when the input power was 174 mW. The measured results agree well with the simulated results, which indicates that the self-bias scheme for Schottky diode-based frequency multipliers is feasible and effective.
- 25 April 2019
- Published by MDPI AG in Micromachines
- Vol. 10 (4) , 277
Open AccessA 135-190 GHz Broadband Self-Biased Frequency Doubler using Four-Anode Schottky Diodes
This paper describes the design and demonstration of a 135–190 GHz self-biased broadband frequency doubler based on planar Schottky diodes. Unlike traditional bias schemes, the diodes are biased in resistive mode by a self-bias resistor; thus, no additional bias voltage is needed for the doubler. The Schottky diodes in this verification are micron-scaled devices with an anode area of 6.6 μm2 and an epitaxial layer thickness of 0.26 μm. For accurate design of the doubler, the 3D-EM model of the Schottky diode is built up to extract the parasitic parameters induced by the diode package when frequency rises up to the terahertz band. In order to implement broadband working, input waveguide steps, output suspended microstrip steps, and output probe with bias filter are all used as matching elements for impedance matching. Measured results show that the doubler exhibits a 3 dB bandwidth of 34% from 135 GHz to 190 GHz, with a conversion efficiency of above 4% when supplied with 100 mW of input power. A 17.8 mW peak output power with a 10.2% efficiency was measured at 166 GHz when the input power was 174 mW. The measured results agree well with the simulated results, which indicates that the self-bias scheme for Schottky diode-based frequency multipliers is feasible and effective.