Narongchai O-Charoen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Narongchai O-Charoen has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ektinai Jansri
Division of Polymer Materials Technology, Faculty of Agricultural Product Innovation and Technology, Srinakharinwirot University, Nakhon Nayok 26120, Thailand
2 shared publications - Piyaporn Kampeerapappun
Faculty of Textile Industries, Rajamangala University of Technology Krungthep, Bangkok 10120, Thailand
2 shared publications - Ektinai Jansri
Energy and Materials Engineering , Rajamangala University of Technology Thanyaburi , 39 Moo 1 Rangsit-Nakhonnayok Rd , Thanyaburi 12110, Pathum Thani , Thailand
1 shared publication - Khanittha Charoenlarp
Faculty of Textile Industries, Rajamangala University of Technology Krungthep, Bangkok 10120, Thailand
1 shared publication - Nawadon Petchwattana
Department of Chemical Engineering, Faculty of Engineering, Srinakharinwirot University, Nakhon Nayok, Thailand
1 shared publication - Pisit Dhamvithee
Division of Food Science and Nutrition, Faculty of Agricultural Product Innovation and Technology, Srinakharinwirot University, Nakhon Nayok 26120, Thailand
1 shared publication
Latest Publications
- Open Access
Biocomposite Based on Polylactic Acid and Rice Straw for Food Packaging Products
Plastic containers, commonly produced from non-biodegradable petroleum-based plastics such as polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET), raise significant environmental concerns due to their persistence. The disposal of agricultural waste, specifically rice straw (RS), through burning, further compounds these environmental issues. In response, this study explores the integration of polylactic acid (PLA), a biodegradable material, with RS using a twin-screw extruder and injection process, resulting in the creation of a biodegradable packaging material. The inclusion of RS led to a decrease in the melt flow rate, thermal stability, and tensile strength, while concurrently enhancing the hydrophilic properties of the composite polymers. Additionally, the incorporation of maleic anhydride (MA) contributed to a reduction in the water absorption rate. The optimized formulation underwent migration testing and met the standards for food packaging products. Furthermore, no MA migration was detected from the composite. This approach not only provides a practical solution for the disposal of RS, but also serves as an environmentally-friendly alternative to conventional synthetic plastic waste.
Open AccessBiocomposite Based on Polylactic Acid and Rice Straw for Food Packaging Products
Plastic containers, commonly produced from non-biodegradable petroleum-based plastics such as polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET), raise significant environmental concerns due to their persistence. The disposal of agricultural waste, specifically rice straw (RS), through burning, further compounds these environmental issues. In response, this study explores the integration of polylactic acid (PLA), a biodegradable material, with RS using a twin-screw extruder and injection process, resulting in the creation of a biodegradable packaging material. The inclusion of RS led to a decrease in the melt flow rate, thermal stability, and tensile strength, while concurrently enhancing the hydrophilic properties of the composite polymers. Additionally, the incorporation of maleic anhydride (MA) contributed to a reduction in the water absorption rate. The optimized formulation underwent migration testing and met the standards for food packaging products. Furthermore, no MA migration was detected from the composite. This approach not only provides a practical solution for the disposal of RS, but also serves as an environmentally-friendly alternative to conventional synthetic plastic waste.
- Open Access
Green Composites Based on PLA and Cotton Fabric Waste: Preparation and Characterization
Textile waste, from both consumption and production, has dramatically increased due to a lack of diversification in its use. Increasing the number of textile alternatives can help to solve these problems. Producing a green composite product is an interesting alternative method. The objectives of this work were to study the preparation and characterization of green composites created from PLA and cotton fabric waste (CFW) and to consider the effect of the CFW content on the composites. The procedure of the research began with CFW pellets preparation; this was subsequently compounded with PLA pellets using a melt-mixing technique with a twin-screw extruder at ratios of 90:10, 80:20, and 70:30 wt% between the PLA and cotton fabric waste, respectively. Then, the testing specimens were produced by compression molding. The experiments demonstrated that an increase in the CFW caused an increase in the viscosity, stiffness, Tg, Tm, and water absorption of the composites. The decomposition temperature of the composites showed a range of 302.41 to 361.22 °C; this decreased when the CFW increased. An increase in the CFW also produced greater and clearer phase separation and roughness on the fracture surface area.
Open AccessGreen Composites Based on PLA and Cotton Fabric Waste: Preparation and Characterization
Textile waste, from both consumption and production, has dramatically increased due to a lack of diversification in its use. Increasing the number of textile alternatives can help to solve these problems. Producing a green composite product is an interesting alternative method. The objectives of this work were to study the preparation and characterization of green composites created from PLA and cotton fabric waste (CFW) and to consider the effect of the CFW content on the composites. The procedure of the research began with CFW pellets preparation; this was subsequently compounded with PLA pellets using a melt-mixing technique with a twin-screw extruder at ratios of 90:10, 80:20, and 70:30 wt% between the PLA and cotton fabric waste, respectively. Then, the testing specimens were produced by compression molding. The experiments demonstrated that an increase in the CFW caused an increase in the viscosity, stiffness, Tg, Tm, and water absorption of the composites. The decomposition temperature of the composites showed a range of 302.41 to 361.22 °C; this decreased when the CFW increased. An increase in the CFW also produced greater and clearer phase separation and roughness on the fracture surface area.
- 19 February 2018
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 38 (7) , 685-694
Polypropylene/polyethylene two-layered by one-step rotational molding
At present, a two-layered product can be molded through various processes. The rotational molding process is a thermoplastics process that can produce products with a two-layered structure; however, it requires special equipment or additional steps in the processing, which make the processing more complex. However, previous research has shown that, through the use of materials with different particle sizes and melting points, two-layered products can also be molded. Thus, this research uses an axial powder flow apparatus to determine the possibility of a two-layered molding between polypropylene (PP) and linear low-density polyethylene (LLDPE). The differences in the particle shapes of a PP homopolymer and copolymer have been considered. The particle sizes of both PPs were determined to be larger than that of LLDPE, and were mixed in a ratio of 50:50 (%wt) using a dry blending method. The results of this experiment show that the two-layered molding of PP and LLDPE using an uncomplicated technique for rotational molding has a high probability of success.
- 19 February 2018
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 38 (7) , 685-694
Polypropylene/polyethylene two-layered by one-step rotational molding
At present, a two-layered product can be molded through various processes. The rotational molding process is a thermoplastics process that can produce products with a two-layered structure; however, it requires special equipment or additional steps in the processing, which make the processing more complex. However, previous research has shown that, through the use of materials with different particle sizes and melting points, two-layered products can also be molded. Thus, this research uses an axial powder flow apparatus to determine the possibility of a two-layered molding between polypropylene (PP) and linear low-density polyethylene (LLDPE). The differences in the particle shapes of a PP homopolymer and copolymer have been considered. The particle sizes of both PPs were determined to be larger than that of LLDPE, and were mixed in a ratio of 50:50 (%wt) using a dry blending method. The results of this experiment show that the two-layered molding of PP and LLDPE using an uncomplicated technique for rotational molding has a high probability of success.