EJEktinai Jansri

Ektinai Jansri

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ektinai Jansri has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Valorization of Velvet Bean Pod Agricultural Residues in Recycled HDPE Composites: The Role of Recycling Cycles and Maleic Anhydride

    by Ektinai Jansri, Narongchai O-Charoen, Piyaporn Kampeerapappun

    The growing demand for plastics, combined with low recycling rates and poor waste management, has led to severe plastic accumulation. Concurrently, rising agricultural residues motivate efforts to valorize both waste streams. This study investigates recycled high-density polyethylene (rHDPE) reinforced with 20 wt % velvet bean pod (VBP) powder, with and without 1 phr maleic anhydride (MA) as a compatibilizer, across one, three, and five successive injection molding cycles. Mechanical, thermal, morphological, rheological, spectroscopic (FTIR), and flammability properties were examined. Without MA, repeated recycling induced chain scission and voids, reducing toughness and density while slightly increasing stiffness due to filler fracture. FTIR spectra of MA-modified composites showed stronger, shifted carbonyl peaks (1718–1740 cm–1), confirming ester bond formation between anhydride groups of MA and hydroxyl groups of VBP and indicating improved interfacial adhesion and mechanical integrity. MA addition stabilized the melt flow index (1.3–1.5 g/10 min), preserved tensile strength (∼22 MPa), increased modulus (up to 558 MPa) and impact toughness (10.6 kJ/m2), reduced water absorption (0.39 to 0.17%), and maintained high crystallinity (∼81%). MA-modified composites also exhibited higher onset degradation temperature and achieved a UL-94 HB flame rating with lower burn rate (∼29 mm/min). The rHDPE5/VBP/MA composite demonstrated the best stiffness–toughness balance, confirming that agricultural residues can be upcycled with recycled plastics into dimensionally stable, reprocessable composites. This approach advances circular-economy goals, aligns with UN SDGs 12 and 13, and offers scalable potential for automotive, landscaping, and construction uses.

  • Open Access

    Effect of thanaka powder (TK) content on the structural and functional properties of polylactic acid/TK composites for sustainable packaging

    by Ektinai Jansri, Narongchai O-Charoen, Pattarawit Rukthong, Khanittha Charoenlarp, Porawan Naksang, Nattaya Vuthiganond, Piyaporn Kampeerapappun

  • Open Access

    Biocomposite Based on Polylactic Acid and Rice Straw for Food Packaging Products

    by Piyaporn Kampeerapappun, Narongchai O-Charoen, Pisit Dhamvithee, Ektinai Jansri

    Plastic containers, commonly produced from non-biodegradable petroleum-based plastics such as polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET), raise significant environmental concerns due to their persistence. The disposal of agricultural waste, specifically rice straw (RS), through burning, further compounds these environmental issues. In response, this study explores the integration of polylactic acid (PLA), a biodegradable material, with RS using a twin-screw extruder and injection process, resulting in the creation of a biodegradable packaging material. The inclusion of RS led to a decrease in the melt flow rate, thermal stability, and tensile strength, while concurrently enhancing the hydrophilic properties of the composite polymers. Additionally, the incorporation of maleic anhydride (MA) contributed to a reduction in the water absorption rate. The optimized formulation underwent migration testing and met the standards for food packaging products. Furthermore, no MA migration was detected from the composite. This approach not only provides a practical solution for the disposal of RS, but also serves as an environmentally-friendly alternative to conventional synthetic plastic waste.


  • Open Access

    Green Composites Based on PLA and Cotton Fabric Waste: Preparation and Characterization

    by Narongchai O-Charoen, Piyaporn Kampeerapappun, Khanittha Charoenlarp, Nawadon Petchwattana, Ektinai Jansri

    Textile waste, from both consumption and production, has dramatically increased due to a lack of diversification in its use. Increasing the number of textile alternatives can help to solve these problems. Producing a green composite product is an interesting alternative method. The objectives of this work were to study the preparation and characterization of green composites created from PLA and cotton fabric waste (CFW) and to consider the effect of the CFW content on the composites. The procedure of the research began with CFW pellets preparation; this was subsequently compounded with PLA pellets using a melt-mixing technique with a twin-screw extruder at ratios of 90:10, 80:20, and 70:30 wt% between the PLA and cotton fabric waste, respectively. Then, the testing specimens were produced by compression molding. The experiments demonstrated that an increase in the CFW caused an increase in the viscosity, stiffness, Tg, Tm, and water absorption of the composites. The decomposition temperature of the composites showed a range of 302.41 to 361.22 °C; this decreased when the CFW increased. An increase in the CFW also produced greater and clearer phase separation and roughness on the fracture surface area.