Keming Cheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Keming Cheng has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Hao Dong
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics 1 , Nanjing, Jiangsu
4 shared publications - Xi Geng
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
2 shared publications - Yunsong Gu
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
2 shared publications - Zhiwei Shi
College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
2 shared publications - Chengpeng Wang
Nanjing University of Aeronautics and Astronautics
1 shared publication - Dawei Liu
High-Speed Aerodynamic Institute, China Aerodynamics Research and Development Center, Mianyang 621000, China
1 shared publication
Latest Publications
- Open Access
- 25 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12482
Multi-Objective Robust Design of Segmented Thermoelectric–Thermal Protection Structures for Hypersonic Vehicles Using a High-Fidelity Thermal Network
Long-endurance hypersonic vehicles face the dual challenge of withstanding extreme aerodynamic heating while meeting onboard power requirements. Integrating thermoelectric generators within thermal protection systems offers a solution by converting thermal loads into electrical power. However, accurate prediction requires resolving coupled multiphysics, where three-dimensional simulations are computationally prohibitive and existing one-dimensional models lack accuracy. This study develops a quasi-two-dimensional distributed thermal network incorporating shape-factor corrections for rapid, high-fidelity prediction. Multi-objective optimization is performed to balance specific power, thermal expansion mismatch, and thermal margin. Analysis reveals fundamental trade-offs: a maximum-power design achieves 28.1 W/kg but only a 0.8% thermal margin, whereas a balanced design delivers 24.5 W/kg with a 5.1% thermal margin and significantly reduced thermal stress. Despite geometric variations, peak conversion efficiency converges to approximately 13%. This indicates that efficiency is primarily governed by material properties, while geometric optimization effectively tunes temperature and thermal strain distributions, providing guidelines for reliable system development.
- 25 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (23) , 12482
Open AccessMulti-Objective Robust Design of Segmented Thermoelectric–Thermal Protection Structures for Hypersonic Vehicles Using a High-Fidelity Thermal Network
Long-endurance hypersonic vehicles face the dual challenge of withstanding extreme aerodynamic heating while meeting onboard power requirements. Integrating thermoelectric generators within thermal protection systems offers a solution by converting thermal loads into electrical power. However, accurate prediction requires resolving coupled multiphysics, where three-dimensional simulations are computationally prohibitive and existing one-dimensional models lack accuracy. This study develops a quasi-two-dimensional distributed thermal network incorporating shape-factor corrections for rapid, high-fidelity prediction. Multi-objective optimization is performed to balance specific power, thermal expansion mismatch, and thermal margin. Analysis reveals fundamental trade-offs: a maximum-power design achieves 28.1 W/kg but only a 0.8% thermal margin, whereas a balanced design delivers 24.5 W/kg with a 5.1% thermal margin and significantly reduced thermal stress. Despite geometric variations, peak conversion efficiency converges to approximately 13%. This indicates that efficiency is primarily governed by material properties, while geometric optimization effectively tunes temperature and thermal strain distributions, providing guidelines for reliable system development.
- Open Access
Shear Stress Distribution of the Separation Region on a Plate in Supersonic Jet Flow
An experimental study is conducted on the surface shear stress vector distribution on a plate in a supersonic jet flow, with a focus on the separation region. The shear-sensitive liquid crystal coating (SSLCC) technique is employed for the flow visualization and measurement, which is based on the shear stress distribution, and the flow pattern on the plate is captured. The results demonstrate that the nozzle pressure ratio (NPR) is the main inducement to flow evolution, and a high NPR causes a separation region on the plate, where the adverse flow is challenging to the SSLCC technique. Therefore, an improved measurement method for the SSLCC is proposed to successfully obtain the wall shear stress distribution inside the separation and reattachment area. The flow structures on the plate, including the separation and reattachment positions and vortex and adverse flows, are accurately captured in detail, which indicates that this method is practical for measuring the wall shear stress in separated flow.
Open AccessShear Stress Distribution of the Separation Region on a Plate in Supersonic Jet Flow
An experimental study is conducted on the surface shear stress vector distribution on a plate in a supersonic jet flow, with a focus on the separation region. The shear-sensitive liquid crystal coating (SSLCC) technique is employed for the flow visualization and measurement, which is based on the shear stress distribution, and the flow pattern on the plate is captured. The results demonstrate that the nozzle pressure ratio (NPR) is the main inducement to flow evolution, and a high NPR causes a separation region on the plate, where the adverse flow is challenging to the SSLCC technique. Therefore, an improved measurement method for the SSLCC is proposed to successfully obtain the wall shear stress distribution inside the separation and reattachment area. The flow structures on the plate, including the separation and reattachment positions and vortex and adverse flows, are accurately captured in detail, which indicates that this method is practical for measuring the wall shear stress in separated flow.
- Open Access
- 9 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10166
Active Flow Control of a Supercritical Airfoil and Flap with Sweeping Jets
To provide sufficient lift during takeoff and landing, large aircraft are equipped with complicated high-lift devices. The use of simple flaps coupled with active flow control (AFC) can achieve lift improvement while reducing mechanical structure and weight. The present study focuses on verifying the feasibility and effectiveness of simple flaps combined with sweeping jet flow control. An experimental study on the AFC of flaps, using sweeping jets, was carried out using a NASA SC(2)-0410 supercritical airfoil wind-tunnel model at Re = 2.0 × 105 (with velocity V = 10 m/s). In the experiment, the wing angle of attack (α) ranged from 3 to 18°, and the flap deflection angle (δ) ranged from 0 to 30°; the aerodynamic characteristics and surface pressure characteristics of the wing at typical working conditions were analyzed. Using sweeping jets to control the flow on the flaps, the momentum coefficients (for three actuator groups) of the jet are 0.8%, 3.6%, and 8.2%, respectively, and the maximum lift coefficient was increased by approximately 33%. The influence of the sweeping jet flow rate on the aerodynamic performance of the airfoil is analyzed. There are two main reasons for the lift coefficient increase caused by sweeping jet flow: an extra suction peak near the flap and a suction peak increase near the leading edge area caused by induced flow.
- 9 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10166
Open AccessActive Flow Control of a Supercritical Airfoil and Flap with Sweeping Jets
To provide sufficient lift during takeoff and landing, large aircraft are equipped with complicated high-lift devices. The use of simple flaps coupled with active flow control (AFC) can achieve lift improvement while reducing mechanical structure and weight. The present study focuses on verifying the feasibility and effectiveness of simple flaps combined with sweeping jet flow control. An experimental study on the AFC of flaps, using sweeping jets, was carried out using a NASA SC(2)-0410 supercritical airfoil wind-tunnel model at Re = 2.0 × 105 (with velocity V = 10 m/s). In the experiment, the wing angle of attack (α) ranged from 3 to 18°, and the flap deflection angle (δ) ranged from 0 to 30°; the aerodynamic characteristics and surface pressure characteristics of the wing at typical working conditions were analyzed. Using sweeping jets to control the flow on the flaps, the momentum coefficients (for three actuator groups) of the jet are 0.8%, 3.6%, and 8.2%, respectively, and the maximum lift coefficient was increased by approximately 33%. The influence of the sweeping jet flow rate on the aerodynamic performance of the airfoil is analyzed. There are two main reasons for the lift coefficient increase caused by sweeping jet flow: an extra suction peak near the flap and a suction peak increase near the leading edge area caused by induced flow.
- Open Access
Study on Characteristics of an AC Sliding Discharge Plasma Actuator Operating at Different Pressures
Dielectric barrier discharge (DBD) has been one of the most promising techniques for flow control, but the practical application needs a large plasma surface. A three-electrode sliding discharge plasma actuator (SDPA) can generate plasma filling the inter-electrode distance. In this study, the performance of an SDPA for practical flight at low pressures is reported. When the pressure decreases, plasma discharge becomes more intensive. Current peaks and power consumption of electrode 1 become higher at low pressure. Sliding discharge is fully developed at 54 kPa, and the plasma morphology resembles plumes. PIV results show vortex structures and an induced wall jet above the actuator surface. A ‘potential-arc-discharge’ is observed at 38 kPa, leading to an inhomogeneous surface temperature distribution and a velocity decrease of the jet.
Open AccessStudy on Characteristics of an AC Sliding Discharge Plasma Actuator Operating at Different Pressures
Dielectric barrier discharge (DBD) has been one of the most promising techniques for flow control, but the practical application needs a large plasma surface. A three-electrode sliding discharge plasma actuator (SDPA) can generate plasma filling the inter-electrode distance. In this study, the performance of an SDPA for practical flight at low pressures is reported. When the pressure decreases, plasma discharge becomes more intensive. Current peaks and power consumption of electrode 1 become higher at low pressure. Sliding discharge is fully developed at 54 kPa, and the plasma morphology resembles plumes. PIV results show vortex structures and an induced wall jet above the actuator surface. A ‘potential-arc-discharge’ is observed at 38 kPa, leading to an inhomogeneous surface temperature distribution and a velocity decrease of the jet.
- Open Access
- 5 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 786
Experimental Study of Vertical Tail Model Flow Control Based on Oscillating Jet
In this paper, wind tunnel experiments are conducted to study the control law and mechanism of oscillating jet flow control to improve the aerodynamic characteristics of the vertical tail when a civil aircraft encounters left side gust or significant crosswind during takeoff and landing. We measured the vertical tail scaling model’s aerodynamics, spatial flow field, and surface pressure when the Reynolds number was 2.12 × 105. The maximum momentum coefficient of the oscillating jet actuator reaches 0.332%. In addition, we studied the flow control effect of the three-dimensional vertical tail scaled model in different spanwise positions. The experimental results show that the oscillating jet at the rear edge of the stabilizer can significantly increase the lateral force of the vertical tail, and the increment of the lateral force can reach 36.5% under the worst condition of the negative side slip angle of the vertical tail. We can improve the lateral force coefficient of the vertical tail model by applying flow control alone at different spanwise locations. The wing root’s control effect and the vertical tail’s middle section are better than the wing tip’s. The oscillating jet can effectively restrain the flow separation on the rudder. In addition, the input of a high-energy jet “ejects” the mainstream, which increases the flow velocity at the side of the vertical tail actuator. It increases the circulation of the vertical tail. The oscillating jet flow control technology can effectively improve the vertical tail’s steering efficiency and increase the vertical tail’s lateral force, which is of great significance in improving the safety and economy of civil aircraft.
- 5 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 786
Open AccessExperimental Study of Vertical Tail Model Flow Control Based on Oscillating Jet
In this paper, wind tunnel experiments are conducted to study the control law and mechanism of oscillating jet flow control to improve the aerodynamic characteristics of the vertical tail when a civil aircraft encounters left side gust or significant crosswind during takeoff and landing. We measured the vertical tail scaling model’s aerodynamics, spatial flow field, and surface pressure when the Reynolds number was 2.12 × 105. The maximum momentum coefficient of the oscillating jet actuator reaches 0.332%. In addition, we studied the flow control effect of the three-dimensional vertical tail scaled model in different spanwise positions. The experimental results show that the oscillating jet at the rear edge of the stabilizer can significantly increase the lateral force of the vertical tail, and the increment of the lateral force can reach 36.5% under the worst condition of the negative side slip angle of the vertical tail. We can improve the lateral force coefficient of the vertical tail model by applying flow control alone at different spanwise locations. The wing root’s control effect and the vertical tail’s middle section are better than the wing tip’s. The oscillating jet can effectively restrain the flow separation on the rudder. In addition, the input of a high-energy jet “ejects” the mainstream, which increases the flow velocity at the side of the vertical tail actuator. It increases the circulation of the vertical tail. The oscillating jet flow control technology can effectively improve the vertical tail’s steering efficiency and increase the vertical tail’s lateral force, which is of great significance in improving the safety and economy of civil aircraft.
- Open Access
- 28 February 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (5) , 1596
Geometric Effects Analysis and Verification of V-Shaped Support Interference on Blended Wing Body Aircraft
A special V-shaped support for blended wing body aircraft was designed and applied in high-speed wind tunnel tests. In order to reduce the support interference and explore the design criteria of the V-shaped support, interference characteristics and geometric parameter effects of V-shaped support on blended wing body aircraft were numerically studied. According to the numerical results, the corresponding dummy V-shaped supports were designed and manufactured, and verification tests was conducted in a 2.4 m × 2.4 m transonic wind tunnel. The test results were in good agreement with the numerical simulation. Results indicated that pitching moment of blended wing body aircraft is quite sensitive to the V-shaped support geometric parameters, and the influence of the inflection angle is the most serious. To minimize the pitching moment interference, the straight-section diameter and inflection angle should be increased while the straight-section length should be shortened. The results could be used to design special V-shaped support for blended wing body aircraft in wind tunnel tests, reduce support interference, and improve the accuracy of test results.
- 28 February 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (5) , 1596
Open AccessGeometric Effects Analysis and Verification of V-Shaped Support Interference on Blended Wing Body Aircraft
A special V-shaped support for blended wing body aircraft was designed and applied in high-speed wind tunnel tests. In order to reduce the support interference and explore the design criteria of the V-shaped support, interference characteristics and geometric parameter effects of V-shaped support on blended wing body aircraft were numerically studied. According to the numerical results, the corresponding dummy V-shaped supports were designed and manufactured, and verification tests was conducted in a 2.4 m × 2.4 m transonic wind tunnel. The test results were in good agreement with the numerical simulation. Results indicated that pitching moment of blended wing body aircraft is quite sensitive to the V-shaped support geometric parameters, and the influence of the inflection angle is the most serious. To minimize the pitching moment interference, the straight-section diameter and inflection angle should be increased while the straight-section length should be shortened. The results could be used to design special V-shaped support for blended wing body aircraft in wind tunnel tests, reduce support interference, and improve the accuracy of test results.
- Open Access
Optical Fiber Displacement Sensor Based on Microwave Photonics Interferometry
An optical fiber displacement sensor based on the microwave photonics interferometric (MWPI) method is proposed and experimented, which provides an ideal solution for large range displacement measurement with high resolution. The sensor used a Michelson microwave photonics interferometer to sense the displacement with one sensing arm and a length-adjusted reference arm. The displacement variation would change the period of the microwave response function of the interferometer. According to the principle that the phase difference in one free spectral range (FSR) of the microwave response function is 360°, the displacement can be retrieved by the microwave response function by means of a vector network analyzer (VNA). A programmable path-switching true time delay line was used in the reference arm to decrease the microwave bandwidth. The measurement results show that the displacement sensing range is larger than 3 m and the measurement resolution is 31 μm. Finally, the measurement stability is tested, and the factors affecting the measurement resolution of this method and the main source of errors are investigated in detail.
Open AccessOptical Fiber Displacement Sensor Based on Microwave Photonics Interferometry
An optical fiber displacement sensor based on the microwave photonics interferometric (MWPI) method is proposed and experimented, which provides an ideal solution for large range displacement measurement with high resolution. The sensor used a Michelson microwave photonics interferometer to sense the displacement with one sensing arm and a length-adjusted reference arm. The displacement variation would change the period of the microwave response function of the interferometer. According to the principle that the phase difference in one free spectral range (FSR) of the microwave response function is 360°, the displacement can be retrieved by the microwave response function by means of a vector network analyzer (VNA). A programmable path-switching true time delay line was used in the reference arm to decrease the microwave bandwidth. The measurement results show that the displacement sensing range is larger than 3 m and the measurement resolution is 31 μm. Finally, the measurement stability is tested, and the factors affecting the measurement resolution of this method and the main source of errors are investigated in detail.
- 12 March 2018
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 32 (08)
Experimental investigations on characteristics of boundary layer and control of transition on an airfoil by AC-DBD
Plasma-based flow control is one of the most promising techniques for aerodynamic problems, such as delaying the boundary layer transition. The boundary layer’s characteristics induced by AC-DBD plasma actuators and applied by the actuators to delay the boundary layer transition on airfoil at Ma = 0.3 were experimentally investigated. The PIV measurement was used to study the boundary layer’s characteristics induced by the plasma actuators. The measurement plane, which was parallel to the surface of the actuators and 1 mm above the surface, was involved in the test, including the perpendicular plane. The instantaneous results showed that the induced flow field consisted of many small size unsteady vortices which were eliminated by the time average. The subsequent oil-film interferometry skin friction measurement was conducted on a NASA SC(2)-0712 airfoil at Ma = 0.3. The coefficient of skin friction demonstrates that the plasma actuators successfully delay the boundary layer transition and the efficiency is better at higher driven voltage.
- 12 March 2018
- Published by World Scientific Pub Co Pte Ltd in Modern Physics Letters B
- Vol. 32 (08)
Experimental investigations on characteristics of boundary layer and control of transition on an airfoil by AC-DBD
Plasma-based flow control is one of the most promising techniques for aerodynamic problems, such as delaying the boundary layer transition. The boundary layer’s characteristics induced by AC-DBD plasma actuators and applied by the actuators to delay the boundary layer transition on airfoil at Ma = 0.3 were experimentally investigated. The PIV measurement was used to study the boundary layer’s characteristics induced by the plasma actuators. The measurement plane, which was parallel to the surface of the actuators and 1 mm above the surface, was involved in the test, including the perpendicular plane. The instantaneous results showed that the induced flow field consisted of many small size unsteady vortices which were eliminated by the time average. The subsequent oil-film interferometry skin friction measurement was conducted on a NASA SC(2)-0712 airfoil at Ma = 0.3. The coefficient of skin friction demonstrates that the plasma actuators successfully delay the boundary layer transition and the efficiency is better at higher driven voltage.