HBHarijot Singh Bindra

Harijot Singh Bindra

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Harijot Singh Bindra has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Comprehensive Comparison of Comparators

    by Harijot Singh Bindra, Anojh K. Rajendra

  • Open Access

    A “No Gain” Direct-Conversion IQ RF-to-Bits Receiver Without Active Linear Amplification

    by Jeroen Ponte, Roel Plompen, Emiel Zijlma, Eric A. M. Klumperink, Harijot Singh Bindra, Bram Nauta

    This work describes a direct-conversion IQ receiver (RX) that does not utilize any active linear (power) amplification, covering its design considerations, prototype implementation, and measurement verification. Only RLC components, MOS transistor (MOST) switches, and comparators are used, leading to several unique design challenges. Key among these are the fact that each block in the signal chain contributes to overall loss, together setting the RF input impedance and thereby RX input matching, plus the limited frequency selectivity of the available passive filters. By considering a fundamental minimum power consumption limit of analog-to-digital converters (ADCs) given by Vittoz, we show that applying impedance up-transformation in the RF front end (RFE) lowers the (minimal) power consumption of the back-end quantization ADC. In our proposed RX, this is implemented by a resonant monolithic transformer followed by a capacitive-stacking N-path filter/mixer (CSNPFM). The resulting RFE architecture simultaneously implements blocker rejection, frequency translation to baseband (BB), and a ~ $\boldsymbol {40\times }$ power consumption reduction in the back-end ADC. The poor frequency selectivity of passive integrated filters renders the implementation of anti-alias filter (AAF) challenging. To avoid their necessity, a highly oversampled delta-sigma modulator back end synchronously digitizes the CSNPFM’s output samples. A prototype RX, implemented in a 22 nm fully-depleted silicon on insulator (FD-SOI) process, has a 10 MHz RF bandwidth (BW) centered around 2.5 GHz and occupies an area of 0.14 mm2 while consuming 10.1 mW. Its measured double-sideband (DSB) noise figure (NF) is 20.5 dB, and its out-of-band (OOB) input intercept point 3 (IIP3) and B1dB are +16 and −0.3 dBm, respectively.


  • Ultra-Low-Power Dynamic-Bias Comparators With Self-Clocked Latch in 65-nm CMOS

    by Anojh Kumaran Rajendra, Harijot Singh Bindra, Bram Nauta

    This article introduces two comparators featuring a dynamic-bias preamplifier and self-clocked latches, tailored for ultra-low-power and medium-speed applications with <500- $\mu $ V input-referred noise (IRN). The proposed self-clocked latches are activated by the preamplifier outputs and therefore operate with a lower common-mode current, which in turn minimizes the crowbar current that is typically present during the comparison phase in conventionally clocked latches. The proposed comparators do not require an additional clock phase for the latch, thereby reducing the clock drive power consumption for systems employing multiple latches, e.g., in ADCs or memories. The absence of an additional clock phase for latching makes them robust toward clock skews, similar to the “StrongARM comparator.” This article also presents an exhaustive overview of the prior art, the “Schinkel comparator,” and its bottlenecks when optimizing for low-noise low-power applications, thereby motivating the importance of self-clocked latches for such applications. This article also discusses the noise–energy–delay design tradeoffs of the proposed dynamic-bias self-clocked (DBSC) comparators. Fabricated in a 65-nm CMOS process along with a standard Schinkel comparator, the two proposed designs exhibit an IRN of 320 and $460~\mu $ V while consuming approximately 40 fJ of energy per comparison from a 1.2-V supply. The measured CLK-OUT delay stands roughly at 0.5 ns. The results indicate a $2\times $ enhancement in energy efficiency and a $3.7\times $ and $2.6\times $ reduction in IRN with a $2.5\times $ increment in CLK-OUT delay for similar differential input voltages when compared to the “Schinkel comparator.”


  • A 12.8-GS/s Time-Interleaved Sub-Sampling ADC Front End With 38-GHz Input Bandwidth and >39-dB SNDR for 1–32 GHz in 22-nm FDSOI

    by Josef Heel, Harijot Singh Bindra, Simon M. Louwsma, Alessandro Dezzani, Bram Nauta

    In this article, we present a $4\times $ time-interleaved analog-to-digital converter (ADC) front end operating at 12.8 GS/s. We designed for a high tracking bandwidth (BW) of 38 GHz and optimized the SNDR up to the 5th Nyquist zone. This allows covering the targeted Ka-band frequencies of 27–31 GHz allocated for high-throughput Earth-to-satellite communication without the need for a dedicated mixer, enabling a wideband direct RF sub-sampling receiver approach. We employ an inductor-based input network together with co-optimized push–pull buffers and an active bootstrapping concept in the critical first track-and-hold (TH) for BW enhancement and improved linearity. Because the focus of this work lies in achieving a high SNDR at multi-ten-GHz inputs rather than maximizing the sampling rate $f {_{S}}$ , we implement a single 1st-rank TH to eliminate the need for skew and BW mismatch calibration. A prototype of this two-rank TH is implemented in 22-nm FDSOI technology. Measurements of four different chip samples indicate SNDR >39 dB up to 32-GHz input frequency at 12.8-GS/s operation while consuming 87 mW. A sweep of $f {_{S}}$ from 4.8 to 15.2 GHz and ±10% supply variation causes ${S_{{11}}{\lt }}{-}12$ dB is achieved up to 35 GHz.

  • Open Access

    A 0.4–0.9 V Supply Voltage-Flexible Third-Order Passive ΔΣ Modulator With Switched-Capacitor Loop Filter Achieving 71.9 dB Peak SNDR at 4 MHz Bandwidth

    by Jeroen Ponte, Harijot Singh Bindra, Bram Nauta

    This paper describes the design and implementation of a 4 MHz bandwidth 3rd-order Discrete-Time (DT) Passive Delta-Sigma Modulator (PM), which avoids the use of supply voltage-sensitive linear amplifiers. The Switched-Capacitor (SC) operation and amplifier-less nature of its loop filter render the proposed modulator highly supply voltage-and clock frequency-flexible. To explain our design choices, we investigate two key design challenges unique to PMs. Firstly, the noise criticality of the quantizer ADC due to the lack of (voltage) gain in the loop filter preceding it. Secondly, the inaccessibility of the readily synthesizable and highly frequency-selective loop filter frequency responses typically employed in Ms, caused by the absence of linear amplifiers. We show that the noise-power trade-off of the quantizer ADC in 1 bit P$\Delta \Sigma$Ms is the same as that of the first integrator amplifier in Active M. Next, we cover the suitability of several passive filters for use in PM loops. This leads to the selection of the voltage-sampled Charge-Rotating IIR (CR-IIR) filter, for which we show M-oriented design equations, on which we base the design of our 3rd-order DT PM. Measurement results on the resulting prototype PM, implemented in GlobalFoundries 22 nm FD-SOI CMOS, demonstrate that it achieves a 71.9 dB peak SNDR and 4 MHz bandwidth while consuming 4.4 mW from a 0.9 V supply and occupying 0.076mm$^\mathrm{\bf 2}$ of silicon area. The prototype PM continues to operate at a 2.25$\times$ reduced supply voltage of 0.4 V, albeit at a reduced bandwidth of 156.25 kHz, where it achieves a peak SNDR of 62 dB while consuming 37.8 $\mu$W.


  • A Programmable Filtering and Frequency Translation by Aliasing IF Receiver With Alias and Harmonic Rejection

    by Viswesh Kendae Ramkumar, Maikel Huiskamp, Harijot Singh Bindra, Eric Klumperink, Bram Nauta

    A programmable intermediate frequency (IF) receiver is proposed, employing a sampler, time-varying capacitor, and switched-capacitor integrator. It realizes high-order finite impulse response (FIR) low-pass or bandpass filtering (BPF) and frequency translation with harmonic rejection (HR). The receiver’s center frequency and bandwidth (BW) can be independently programmed across the Nyquist zone. The primary focus is on balancing filter stopband rejection with harmonic, image, and alias rejection in a prototype 28 nm CMOS chip design. This work is also the first to address and quantify the adjacent and alternate adjacent channel aliasing in filtering by aliasing filters. The center frequency and BW of the receiver can be programmed to 0–1 GHz and 8–25 MHz, respectively. The receiver achieves a wideband impedance matching S $_{11}$ $<$ $-$ 9 dB across the first Nyquist zone. It employs 8-bit filter coefficients to achieve consistent $>$ 50 dB stopband attenuation at 1 $\times$ BW offset, HR, image rejection (IR), and 50 dB in-band (IB) alias suppression. The I and Q receivers use only a single fixed 1 GHz clock frequency to achieve all the functionality and consume 73.6 mW.


  • A 14-Bit Oversampled SAR ADC With Mismatch Error Shaping and Analog Range Compensation

    by Yuting Shen, Hanyue Li, Harijot Singh Bindra, Eugenio Cantatore, Pieter Harpe

    DAC mismatch is a major challenge for high-resolution ADCs. This paper proposes an analog-detection-based input range compensation technique for high-resolution ADCs with mismatch error shaping (MES). By applying a pre-comparison and suitably switching the DAC MSB, the input loss caused by MES is compensated. By adopting a flying-capacitor sampling technique, the prediction errors found in prior solutions are avoided. The prototype 14-bit SAR ADC achieves 80.4 dB SNDR and 93 dB SFDR in a 4 kHz signal bandwidth with an OSR of 16. It only occupies 0.0034 mm and consumes 0.656 μW under a 0.8 V supply, leading to a Schreier figure-of-merit of 178.3 dB. These features make it suitable for miniaturized high-performance IoT and biomedical systems.


  • Reconstructing Aliased Frequency Spectra by Using Multiple Sample Rates

    by Maikel Huiskamp, Mark S. Oude Alink, Bram Nauta, Anne-Johan Annema, Harijot Singh Bindra

    A novel algorithm is presented that can resolve frequency ambiguity that arises from sampling a set of signals spanning more than a single Nyquist zone. The method uses two samplers, each sampling the same input signal with different (non-integer multiple) sampling rates. The algorithm is able to resolve frequency ambiguity and reconstruct signals with an orthogonal frequency basis spanning multiple Nyquist zones, provided that the aggregate information-bearing bandwidth of the signals is less than half the cumulative data converter sampling rates. This manuscript describes the theoretical background for the algorithm and validates it through measurements performed on a test-board comprising of two 10 bit analog-to-digital converters clocked at two different (non-integer multiple) sample rates. Measurements show that even in the presence of aliasing, an orthogonal signal spanning multiple Nyquist zones can be fully reconstructed.


  • Energy Efficient Startup of Crystal Oscillators Using Stepwise Charging

    by Joeri B. Lechevallier, Harijot Singh Bindra, Ronan A. R. van der Zee, Bram Nauta

    Crystal oscillators can be started up quickly by using energy injection techniques. However, the generation of the injection waveform, as well as driving the large capacitive load formed by the crystal, costs a large amount of energy. This article applies the concept of stepwise charging to reduce the energy required to drive the crystal. The energy required to generate the injection waveform by self-timed injection is reduced by using a discrete-time dynamic-bias comparator which uses a simple offset calibration method. Furthermore, the bridge switch resistance is varied dynamically through self-timed control logic to alleviate the accuracy-speed tradeoff. A prototype was manufactured in a 65-nm (triple-well) CMOS technology, which was tested with various crystals ranging from 24 to 50 MHz, improving upon the state of the art in energy consumption.