Sotya Astutiningsih
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sotya Astutiningsih has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Nuraziz Handika
Universitas Indonesia, Indonesia
6 shared publications - Muhammad Saukani
Department of Mechanical Engineering, Faculty of Engineering, Universitas Islam Kalimantan MAB, Banjarmasin 70124, Indonesia
4 shared publications - Eric Vincens
LTDS
3 shared publications - Jessica Sjah
Department of Civil and Environmental Engineering, Faculty of Engineering, Universitas Indonesia, Depok, 16424, Indonesia
3 shared publications - Mochamad Chalid
Green Polymer Technology Laboratory Department of Metallurgical and Materials Engineering Faculty of Engineering Universitas Indonesia Depok Indonesia
3 shared publications - Adam Febriyanto Nugraha
Green Polymer Technology Laboratory, Department of Metallurgical and Material Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, Indonesia
2 shared publications
Latest Publications
- Open Access
- 30 October 2026
- Published by Elsevier in Next Materials
- Vol. 14
Tensile performance, ultrasonic pulse velocity, and chloride ion content of roller-compacted concrete (RCC) incorporating single and dual nickel slag aggregate replacement
- 30 October 2026
- Published by Elsevier in Next Materials
- Vol. 14
Open AccessTensile performance, ultrasonic pulse velocity, and chloride ion content of roller-compacted concrete (RCC) incorporating single and dual nickel slag aggregate replacement
- Open Access
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1)
Evaluation of Elastic Modulus and Strain Characteristics of Sustainable Concrete With Ferronickel Slag Coarse Aggregate Using Digital Image Correlation
The nickel industry in Indonesia produces approximately 13 million tons of ferronickel slag (FNS) annually, most of which remains underutilized and poses potential environmental concerns. This study investigates the mechanical and deformation characteristics of concrete incorporating FNS as a sustainable replacement for natural coarse aggregate. Experimental tests included workability, compressive strength, ultrasonic pulse velocity (UPV) and digital image correlation (DIC) analyses to evaluate strain development and elastic properties. The inclusion of FNS reduced workability due to its angular particle shape and absorption capacity but enhanced concrete density and strength. The optimum mixture, with 50% FNS (FNS‐50) replacement, achieved the highest compressive strength 38.0% greater than the control (FNS‐0) and the highest modulus of elasticity at 32.2 GPa, representing a 25.6% increase compared with FNS‐0. DIC observations revealed delayed strain localization and fewer columnar cracks in FNS‐40 and FNS‐50 specimens, indicating superior deformation resistance. A positive correlation was observed between compressive strength and elastic modulus, confirming the structural efficiency of FNS concrete. The findings demonstrate that FNS can serve as an effective and environmentally friendly coarse aggregate substitute, contributing to sustainable concrete technology and waste valorisation in the nickel industry.
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1)
Open AccessEvaluation of Elastic Modulus and Strain Characteristics of Sustainable Concrete With Ferronickel Slag Coarse Aggregate Using Digital Image Correlation
The nickel industry in Indonesia produces approximately 13 million tons of ferronickel slag (FNS) annually, most of which remains underutilized and poses potential environmental concerns. This study investigates the mechanical and deformation characteristics of concrete incorporating FNS as a sustainable replacement for natural coarse aggregate. Experimental tests included workability, compressive strength, ultrasonic pulse velocity (UPV) and digital image correlation (DIC) analyses to evaluate strain development and elastic properties. The inclusion of FNS reduced workability due to its angular particle shape and absorption capacity but enhanced concrete density and strength. The optimum mixture, with 50% FNS (FNS‐50) replacement, achieved the highest compressive strength 38.0% greater than the control (FNS‐0) and the highest modulus of elasticity at 32.2 GPa, representing a 25.6% increase compared with FNS‐0. DIC observations revealed delayed strain localization and fewer columnar cracks in FNS‐40 and FNS‐50 specimens, indicating superior deformation resistance. A positive correlation was observed between compressive strength and elastic modulus, confirming the structural efficiency of FNS concrete. The findings demonstrate that FNS can serve as an effective and environmentally friendly coarse aggregate substitute, contributing to sustainable concrete technology and waste valorisation in the nickel industry.
- Open Access
- 22 August 2025
- Published by Elsevier in Cleaner Waste Systems
- Vol. 12
A comparative study of the life cycle assessment of natural, recycled, and oil palm shell aggregate concretes
- 22 August 2025
- Published by Elsevier in Cleaner Waste Systems
- Vol. 12
Open AccessA comparative study of the life cycle assessment of natural, recycled, and oil palm shell aggregate concretes
- Open Access
- 30 August 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (9) , 341
Mechanical and Physical Characteristics of Oil Palm Empty Fruit Bunch as Fine Aggregate Replacement in Ordinary Portland Cement Mortar Composites
Palm oil empty fruit bunch (OEB) is the largest source of waste in the production of crude palm oil. Utilizing this waste in various applications can help reduce its volume and mitigate adverse environmental effects. In this study, fibers from OEB without any chemical treatment are introduced into Ordinary Portland Cement (OPC)-based mortar to partially replace fine aggregates, aiming to reduce the mortar’s density. The goal of this experimental study is to observe the mechanical and physical performance of the samples according to the effect of the addition of OEB. The composite samples were made by replacing 1%, 2%, and 3% of the weight of quartz sand as the fine aggregate with OEB (fine and coarse). The hardened composites were further tested to determine their compressive strength, and it was found that the replacement of sand with OEB led to a decrease in compressive strength and flowability while alleviating the mortar’s density and affecting the setting time. The decrease in compressive strength was attributed to cavities present in the samples. Flexural tests and 28-day drying shrinkage measurements were carried out on the samples with 1% replacement of sand with OEB. The experiments showed that OEB fibers increased the flexural strength, functioned as a crack barrier, and reduced drying shrinkage.
- 30 August 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (9) , 341
Open AccessMechanical and Physical Characteristics of Oil Palm Empty Fruit Bunch as Fine Aggregate Replacement in Ordinary Portland Cement Mortar Composites
Palm oil empty fruit bunch (OEB) is the largest source of waste in the production of crude palm oil. Utilizing this waste in various applications can help reduce its volume and mitigate adverse environmental effects. In this study, fibers from OEB without any chemical treatment are introduced into Ordinary Portland Cement (OPC)-based mortar to partially replace fine aggregates, aiming to reduce the mortar’s density. The goal of this experimental study is to observe the mechanical and physical performance of the samples according to the effect of the addition of OEB. The composite samples were made by replacing 1%, 2%, and 3% of the weight of quartz sand as the fine aggregate with OEB (fine and coarse). The hardened composites were further tested to determine their compressive strength, and it was found that the replacement of sand with OEB led to a decrease in compressive strength and flowability while alleviating the mortar’s density and affecting the setting time. The decrease in compressive strength was attributed to cavities present in the samples. Flexural tests and 28-day drying shrinkage measurements were carried out on the samples with 1% replacement of sand with OEB. The experiments showed that OEB fibers increased the flexural strength, functioned as a crack barrier, and reduced drying shrinkage.
- Open Access
Experimental and Finite Element Analysis of Reinforced Concrete Beams Using Ferronickel Slag as Partial Replacement for Fine Aggregate under Semi-Cyclic Loading
The smelting process of Ferronickel in Indonesia produces a significant amount of waste in the form of Ferronickel Slag (FNS), with an annual accumulation of up to 13 million metric tons. Previous studies have shown promising strength results for concrete utilizing FNS as a fine aggregate. This study aims to analyze the mechanical properties of three reinforced concrete (RC) beams measuring 15 cm × 25 cm × 300 cm, each containing FNS as a 50% substitute for fine aggregate. The RC Beams underwent experimental testing using a four-point loading scheme under semi-cyclic loading conditions. Test results show the beams’ capacity had reached up to 8 ton-f and their load–displacement responses show promising results. Digital Image Correlation (DIC) analysis facilitated the observation of surface deformation evolution due to loading, aiding in the identification of concrete crack patterns. Due to semi-cyclic loading, cracks on the beams’ surface were experiencing a crack opening and closing phenomenon, where the propagations of cracks ceased or reclosed throughout the unloading process. Moreover, the opening of residual cracks was also captured by DIC analysis. The experimental finding was validated by finite element analysis. The RC beam numerical model was created using the Timoshenko Multi-fiber element in CAST3M software version 2022. Mazars concrete and elastoplastic steel damage model were used as constitutive laws for numerical modeling. The model’s load–displacement response demonstrated satisfactory agreement compared to the experimental monotonic loading result. However, the model had limitations regarding the simulation of residual displacements of beams due to semi-cyclic loading.
Open AccessExperimental and Finite Element Analysis of Reinforced Concrete Beams Using Ferronickel Slag as Partial Replacement for Fine Aggregate under Semi-Cyclic Loading
The smelting process of Ferronickel in Indonesia produces a significant amount of waste in the form of Ferronickel Slag (FNS), with an annual accumulation of up to 13 million metric tons. Previous studies have shown promising strength results for concrete utilizing FNS as a fine aggregate. This study aims to analyze the mechanical properties of three reinforced concrete (RC) beams measuring 15 cm × 25 cm × 300 cm, each containing FNS as a 50% substitute for fine aggregate. The RC Beams underwent experimental testing using a four-point loading scheme under semi-cyclic loading conditions. Test results show the beams’ capacity had reached up to 8 ton-f and their load–displacement responses show promising results. Digital Image Correlation (DIC) analysis facilitated the observation of surface deformation evolution due to loading, aiding in the identification of concrete crack patterns. Due to semi-cyclic loading, cracks on the beams’ surface were experiencing a crack opening and closing phenomenon, where the propagations of cracks ceased or reclosed throughout the unloading process. Moreover, the opening of residual cracks was also captured by DIC analysis. The experimental finding was validated by finite element analysis. The RC beam numerical model was created using the Timoshenko Multi-fiber element in CAST3M software version 2022. Mazars concrete and elastoplastic steel damage model were used as constitutive laws for numerical modeling. The model’s load–displacement response demonstrated satisfactory agreement compared to the experimental monotonic loading result. However, the model had limitations regarding the simulation of residual displacements of beams due to semi-cyclic loading.
- 22 February 2024
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1114, 145-152
Curing Kinetics of Epoxy Adhesive by Non-Isothermal DSC
Non-isothermal DSC has been used to investigate the curing kinetics of epoxy adhesives (DGEBA-cycloaliphatic amine). The epoxy samples were scanned on DSC with five heating rates (5°C/min, 7.5°C/min, 10°C/min, 12.5°C/min, and 15°C/min). The curing kinetics were obtained through ASTM standards E2890 and E698 (the Ozawa and Kissinger methods). The kinetic parameters obtained include Ea (activation energy), A (pre-exponential factor), and n (reaction order). The activation energy calculated from the Kissinger and Ozawa method was slightly different but insignificant. The reaction rate (dα/dt) and degree of curing/conversion (α) relationship towards temperature (T), and time (t) was also investigated. The curing process's reaction rate (dα/dt) has maximum value; it can no longer increase after a specific conversion rate (α).
- 22 February 2024
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1114, 145-152
Curing Kinetics of Epoxy Adhesive by Non-Isothermal DSC
Non-isothermal DSC has been used to investigate the curing kinetics of epoxy adhesives (DGEBA-cycloaliphatic amine). The epoxy samples were scanned on DSC with five heating rates (5°C/min, 7.5°C/min, 10°C/min, 12.5°C/min, and 15°C/min). The curing kinetics were obtained through ASTM standards E2890 and E698 (the Ozawa and Kissinger methods). The kinetic parameters obtained include Ea (activation energy), A (pre-exponential factor), and n (reaction order). The activation energy calculated from the Kissinger and Ozawa method was slightly different but insignificant. The reaction rate (dα/dt) and degree of curing/conversion (α) relationship towards temperature (T), and time (t) was also investigated. The curing process's reaction rate (dα/dt) has maximum value; it can no longer increase after a specific conversion rate (α).
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3219 (1) , 100009
Characterization of physical and mechanical properties of ferronickel slag based-geopolymer with POFA activator
Geopolymer is an environmentally friendly binder material resulting from the synthesis of aluminosilicate materials in an alkaline environment. Indonesia is the Geopolymer is an environmentally friendly binder material resulting from the synthesis of aluminosilicate materials in an alkaline environment. Indonesia is the
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3219 (1) , 100009
Characterization of physical and mechanical properties of ferronickel slag based-geopolymer with POFA activator
Geopolymer is an environmentally friendly binder material resulting from the synthesis of aluminosilicate materials in an alkaline environment. Indonesia is the Geopolymer is an environmentally friendly binder material resulting from the synthesis of aluminosilicate materials in an alkaline environment. Indonesia is the
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3221 (1) , 040001
Electrochemical characterizations of green solid polymer electrolyte based on PVA-chitosan blend
Solid polymer electrolyte membranes have been prepared by blending PVA and chitosan, doped with lithium bis(oxalato) borate electrolyte salt, and plasticized wi Solid polymer electrolyte membranes have been prepared by blending PVA and chitosan, doped with lithium bis(oxalato) borate electrolyte salt, and plasticized wi
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3221 (1) , 040001
Electrochemical characterizations of green solid polymer electrolyte based on PVA-chitosan blend
Solid polymer electrolyte membranes have been prepared by blending PVA and chitosan, doped with lithium bis(oxalato) borate electrolyte salt, and plasticized wi Solid polymer electrolyte membranes have been prepared by blending PVA and chitosan, doped with lithium bis(oxalato) borate electrolyte salt, and plasticized wi
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3114 (1)
Impact of random field-Size effect using Turning Band Method (TBM) on damage behavior modelling of oil palm shell concrete under compression test
As a non-homogenous material, the characteristic tests of concrete in the laboratory do not always represent the quality and the size of the actual condition in As a non-homogenous material, the characteristic tests of concrete in the laboratory do not always represent the quality and the size of the actual condition in
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3114 (1)
Impact of random field-Size effect using Turning Band Method (TBM) on damage behavior modelling of oil palm shell concrete under compression test
As a non-homogenous material, the characteristic tests of concrete in the laboratory do not always represent the quality and the size of the actual condition in As a non-homogenous material, the characteristic tests of concrete in the laboratory do not always represent the quality and the size of the actual condition in
- 14 December 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1109, 97-102
Green Synthesis of Citric Acid-Crosslinked Cellulose Acetate Membrane for Polymer Electrolyte
Safer alternative for lithium-ion battery containing liquid electrolyte was proposed using solid polymer electrolyte as a combo separator/electrolyte. In this work, cellulose acetate (CA) was used to replace fossil-based polymer as battery separator. To further promote sustainable membrane fabrication, dimethylsulfoxide (DMSO) and citric acid was used as solvent and cross-linking agent, respectively. Branched polyethyleneimine (bPEI) was also incorporated in the polymer electrolyte complex to promote electrolyte salt dissociation within the matrix. Crosslinking of CA-bPEI using citric acid showed promising properties compared to unmodified CA membrane. Better thermal stability and lower crystallinity were seen in the modified CA membrane, resulting in better ionic conductivity.
- 14 December 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1109, 97-102
Green Synthesis of Citric Acid-Crosslinked Cellulose Acetate Membrane for Polymer Electrolyte
Safer alternative for lithium-ion battery containing liquid electrolyte was proposed using solid polymer electrolyte as a combo separator/electrolyte. In this work, cellulose acetate (CA) was used to replace fossil-based polymer as battery separator. To further promote sustainable membrane fabrication, dimethylsulfoxide (DMSO) and citric acid was used as solvent and cross-linking agent, respectively. Branched polyethyleneimine (bPEI) was also incorporated in the polymer electrolyte complex to promote electrolyte salt dissociation within the matrix. Crosslinking of CA-bPEI using citric acid showed promising properties compared to unmodified CA membrane. Better thermal stability and lower crystallinity were seen in the modified CA membrane, resulting in better ionic conductivity.