Mehmet Ayvaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mehmet Ayvaz has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Emre Özer
Osmaniye Korkut Ata University, Faculty of Engineering, Department of Industrial Engineering
3 shared publications - Hakan Cetinel
Manisa
3 shared publications - Burak Gül
Celal Bayar University, Engineering Faculty. Department of Mechanical Engineering
2 shared publications Hakan Cetinel
Manisa , Turkey
2 shared publications- Levent Ulvi Gezici
Celal Bayar University, Engineering Faculty. Department of Mechanical Engineering
2 shared publications - Mustafa Übeyli
Osmaniye Korkut Ata University , Faculty of Engineering and Natural Sciences , Mechanical Engineering Department , Karacaoglan Campus, 80000 , Osmaniye , Türkiye
2 shared publications
Latest Publications
- Open Access
- 17 June 2026
- Published by Folium Publishing Company in Металловедение и термическая обработка металлов
- No. 6,p. 36-37
Dry sliding wear behavior of Al – Cu – Mg – Si alloy – Gr/SiC composites sintered via microwave heating
Исследовано влияние армирования различным количеством карбида кремния SiC при сохранении фиксированного содержания графена (Gr) на уровне 3 % (масс.) на структуру и свойства композита на основе алюминиевого сплава системы Al – Mg – Si – Cu. Порошки смешивали в течение 2 ч для достижения однородного распределения армирующего материала. Смешанные порошки однонаправленно прессовали при давлении 600 МПа с использованием 100-тонного пресса. Металломатричные композиты Al – Mg – Si – Cu, армированные Gr и SiC, спекали в микроволновой печи при 600 °C, 30 мин со скоростью нагрева 15 °C/мин. Изучена микроструктура, измерена микротвердость и определены трибологические свойства полученных гибридных композитов. Проведен микроструктурный анализ методом сканирующей электронной микроскопии с применением детекторов вторичных электронов и обратно-рассеянных электронов. Для элементного анализа использована энергодисперсионная рентгеновская спектроскопия. Трибологические испытания выполнены с помощью трибометра. Результаты проведенных исследований показывают, что гибридные композиты на основе Al – Mg – Si – Cu-сплава, армированные Gr и SiC, обладают повышенной износостойкостью.
- 17 June 2026
- Published by Folium Publishing Company in Металловедение и термическая обработка металлов
- No. 6,p. 36-37
Open AccessDry sliding wear behavior of Al – Cu – Mg – Si alloy – Gr/SiC composites sintered via microwave heating
Исследовано влияние армирования различным количеством карбида кремния SiC при сохранении фиксированного содержания графена (Gr) на уровне 3 % (масс.) на структуру и свойства композита на основе алюминиевого сплава системы Al – Mg – Si – Cu. Порошки смешивали в течение 2 ч для достижения однородного распределения армирующего материала. Смешанные порошки однонаправленно прессовали при давлении 600 МПа с использованием 100-тонного пресса. Металломатричные композиты Al – Mg – Si – Cu, армированные Gr и SiC, спекали в микроволновой печи при 600 °C, 30 мин со скоростью нагрева 15 °C/мин. Изучена микроструктура, измерена микротвердость и определены трибологические свойства полученных гибридных композитов. Проведен микроструктурный анализ методом сканирующей электронной микроскопии с применением детекторов вторичных электронов и обратно-рассеянных электронов. Для элементного анализа использована энергодисперсионная рентгеновская спектроскопия. Трибологические испытания выполнены с помощью трибометра. Результаты проведенных исследований показывают, что гибридные композиты на основе Al – Mg – Si – Cu-сплава, армированные Gr и SiC, обладают повышенной износостойкостью.
- 19 January 2026
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 68 (2) , 377-398
In vitro tribological behavior of Mg2Zn1Mn/HA-Al 2 O 3 nano-biocomposites
Magnesium biocomposites reinforced with biocompatible ceramic particles are considered promising biomaterials for orthopedic applications due to their biodegradability and compatibility with bone regeneration. In addition to mechanical and corrosion performance, the in vitro wear behavior of these materials is critical for implant components subjected to frictional loading. In this study, the sliding wear behavior of Mg2Zn1Mn nano-biocomposites reinforced with hydroxyapatite (HA) and alumina (Al 2 O 3 ) nanoparticles was investigated under a 10 N load in both dry and simulated body fluid (SBF) environments. The influence of reinforcement content and sintering route (one-step and two-step) on wear performance was examined. The results revealed that wear losses were higher in SBF than in dry conditions, due to simultaneous corrosion-assisted wear, as well as the incorporation of 6 wt.% HA and Al 2 O 3 nanoparticles, together with two-step sintering, improved in vitro wear resistance by 33.9 %. Scanning electron microscopy analyses showed that abrasive and oxidative wear dominated under dry sliding conditions, whereas corrosive wear became the primary mechanism in SBF. These findings demonstrate that dual ceramic reinforcement significantly enhances the wear resistance of Mg2Zn1Mn biocomposites, particularly in physiological environments.
- 19 January 2026
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 68 (2) , 377-398
In vitro tribological behavior of Mg2Zn1Mn/HA-Al 2 O 3 nano-biocomposites
Magnesium biocomposites reinforced with biocompatible ceramic particles are considered promising biomaterials for orthopedic applications due to their biodegradability and compatibility with bone regeneration. In addition to mechanical and corrosion performance, the in vitro wear behavior of these materials is critical for implant components subjected to frictional loading. In this study, the sliding wear behavior of Mg2Zn1Mn nano-biocomposites reinforced with hydroxyapatite (HA) and alumina (Al 2 O 3 ) nanoparticles was investigated under a 10 N load in both dry and simulated body fluid (SBF) environments. The influence of reinforcement content and sintering route (one-step and two-step) on wear performance was examined. The results revealed that wear losses were higher in SBF than in dry conditions, due to simultaneous corrosion-assisted wear, as well as the incorporation of 6 wt.% HA and Al 2 O 3 nanoparticles, together with two-step sintering, improved in vitro wear resistance by 33.9 %. Scanning electron microscopy analyses showed that abrasive and oxidative wear dominated under dry sliding conditions, whereas corrosive wear became the primary mechanism in SBF. These findings demonstrate that dual ceramic reinforcement significantly enhances the wear resistance of Mg2Zn1Mn biocomposites, particularly in physiological environments.
- 2 February 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 334
Microstructural, mechanical, wear and corrosion properties of Mg3Zn/TiB2-CNT nanocomposites
- 2 February 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 334
Microstructural, mechanical, wear and corrosion properties of Mg3Zn/TiB2-CNT nanocomposites
- 27 December 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (2) , 233-247
Dry tribological behaviour of microwave-assisted sintered AA2024 matrix hybrid composites reinforced by TiC/B4C/nano-graphite particles
This study aimed to produce hybrid composites with a AA2024 matrix reinforced by TiC/B4C/nano-graphite through a microwave-assisted sintering technique at 560 °C for 60 min. The nano-graphite ratio in the produced composite samples was kept constant as 1 wt.%. TiC and B4C were used in equal ratios at 2, 6 and 10 % by weight total to determine their effects on tribological properties. Wear tests were conducted under three different loads: 3, 5 and 10 N. In the hybrid composites produced, an inverse correlation was observed between the increase in reinforcement ratio and sinterability, while a direct correlation relationship was found in hardness and wear resistance. Compared to the sample containing 2 % TiC/B4C in total by weight, a ∼50 % increase in Brinell hardness and a 52–68 % decrease in wear rate was obtained in the sample containing 10 % TiC/B4C. As the reinforcement ratio increased, tribofilm formation increased, and abrasive wear was replaced by mild-oxidative wear type.
- 27 December 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (2) , 233-247
Dry tribological behaviour of microwave-assisted sintered AA2024 matrix hybrid composites reinforced by TiC/B4C/nano-graphite particles
This study aimed to produce hybrid composites with a AA2024 matrix reinforced by TiC/B4C/nano-graphite through a microwave-assisted sintering technique at 560 °C for 60 min. The nano-graphite ratio in the produced composite samples was kept constant as 1 wt.%. TiC and B4C were used in equal ratios at 2, 6 and 10 % by weight total to determine their effects on tribological properties. Wear tests were conducted under three different loads: 3, 5 and 10 N. In the hybrid composites produced, an inverse correlation was observed between the increase in reinforcement ratio and sinterability, while a direct correlation relationship was found in hardness and wear resistance. Compared to the sample containing 2 % TiC/B4C in total by weight, a ∼50 % increase in Brinell hardness and a 52–68 % decrease in wear rate was obtained in the sample containing 10 % TiC/B4C. As the reinforcement ratio increased, tribofilm formation increased, and abrasive wear was replaced by mild-oxidative wear type.
- Open Access
- 15 August 2022
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 6 (2) , 106-112
Hydroxyapatite coating processes with EPD method and investigation of mechanical properties of coatings
This paper reports on electrophoretic deposition of hydroxyapatite coatings on 316L stainless steel and Ti6Al4V alloy. Coatings were carried out at 60 sec. deposition time and voltage values of 40, 80, 120, 160 Voltage. Suspension: It was prepared by using Ethanol, Hydroxyapatite, Polyvinyl Alcohol, Sodium dodecyl sulfate, N-N-Dimethylformamide chemicals. The findings and results acquired at the end of the study have been presented and discussed. When the Ca/P values calculated in the study are examined, it was seen that there are values close to the ideal Ca/P ratio (1.67) in all parameters. When the roughness values are examined, it was seen that coatings close to the ideal surface roughness value (1-1.5 µm) are obtained. When the nano indentation test results were evaluated, it was observed that coatings suitable for shell bone implants were obtained.
- 15 August 2022
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 6 (2) , 106-112
Open AccessHydroxyapatite coating processes with EPD method and investigation of mechanical properties of coatings
This paper reports on electrophoretic deposition of hydroxyapatite coatings on 316L stainless steel and Ti6Al4V alloy. Coatings were carried out at 60 sec. deposition time and voltage values of 40, 80, 120, 160 Voltage. Suspension: It was prepared by using Ethanol, Hydroxyapatite, Polyvinyl Alcohol, Sodium dodecyl sulfate, N-N-Dimethylformamide chemicals. The findings and results acquired at the end of the study have been presented and discussed. When the Ca/P values calculated in the study are examined, it was seen that there are values close to the ideal Ca/P ratio (1.67) in all parameters. When the roughness values are examined, it was seen that coatings close to the ideal surface roughness value (1-1.5 µm) are obtained. When the nano indentation test results were evaluated, it was observed that coatings suitable for shell bone implants were obtained.
- 23 August 2021
- Published by Izmir UOD
Investigation of the Wear Behavior of AA6082 Against Different Counterparts
In this study, the effect of different counterparts on the wear resistance of AA6082 aluminum alloy was investigated. In tests using pin-on-disk method, 6 mm diameter Al2O3, 100Cr6 and WC-6Co balls were used as counterparts. The tests were carried out using 500 m sliding distance and 5N load. The lowest specific wear rate was measured as 7.58x10-4 mm3/Nm in WC-6Co / AA6082 couple, and the highest value was measured as 9.71x10-4 mm3/Nm in 100Cr6/AA6082 couple. In the Al2O3/AA6082 couple, the specific wear rate of the AA6082-T6 sample was determined as 8.23x10-4 mm3/Nm. While it was observed that the dominant wear type in the 100Cr6/AA6082 pair was abrasive wear, oxidation wear and oxide tribofilm were detected in the WC-6Co/AA6082 and Al2O3/AA6082 couple besides the abrasive wear.
- 23 August 2021
- Published by Izmir UOD
Investigation of the Wear Behavior of AA6082 Against Different Counterparts
In this study, the effect of different counterparts on the wear resistance of AA6082 aluminum alloy was investigated. In tests using pin-on-disk method, 6 mm diameter Al2O3, 100Cr6 and WC-6Co balls were used as counterparts. The tests were carried out using 500 m sliding distance and 5N load. The lowest specific wear rate was measured as 7.58x10-4 mm3/Nm in WC-6Co / AA6082 couple, and the highest value was measured as 9.71x10-4 mm3/Nm in 100Cr6/AA6082 couple. In the Al2O3/AA6082 couple, the specific wear rate of the AA6082-T6 sample was determined as 8.23x10-4 mm3/Nm. While it was observed that the dominant wear type in the 100Cr6/AA6082 pair was abrasive wear, oxidation wear and oxide tribofilm were detected in the WC-6Co/AA6082 and Al2O3/AA6082 couple besides the abrasive wear.
- Open Access
- 15 August 2021
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 5 (2) , 181-187
Determination of the effect of artificial aging parameters on dry sliding wear resistance of 6013 aluminum alloy (Al-Mg-Si-Cu)
In this study, the effect of artificial aging parameters, applied to AA6013 aluminum alloys commonly used in the automotive and aerospace sectors, on wear resistance was examined. For this purpose, AA6013 aluminum alloy samples were solutionized at 575 °C for 60 minutes and then they were artificially aged for 2, 4, and 6 hours at 180 and 200 °C temperatures. Mean hardness was measured as 66.6 HV in the solutionized samples taken. It was determined that as a result of artificial aging, α-AlFeMnSi intermetallic phase precipitation were formed between α-Al grains. By the effect of precipitation hardening, an increase in hardness was observed in all artificially aged samples; the highest hardness was found as an average of 149.3 HV in AA6013 samples aged artificially for 2 hours at 200 °C. A general decrease in the friction coefficients of samples aged at both 180 °C and 200 °C was observed along with the artificial aging temperature. The lowest specific wear rate was determined as 3.542x10-3 mm3/Nm in the AA6013 sample aged artificially for 2 hours at 200 °C.
- 15 August 2021
- Published by International Advanced Researches and Engineering Journal in International Advanced Researches and Engineering Journal
- Vol. 5 (2) , 181-187
Open AccessDetermination of the effect of artificial aging parameters on dry sliding wear resistance of 6013 aluminum alloy (Al-Mg-Si-Cu)
In this study, the effect of artificial aging parameters, applied to AA6013 aluminum alloys commonly used in the automotive and aerospace sectors, on wear resistance was examined. For this purpose, AA6013 aluminum alloy samples were solutionized at 575 °C for 60 minutes and then they were artificially aged for 2, 4, and 6 hours at 180 and 200 °C temperatures. Mean hardness was measured as 66.6 HV in the solutionized samples taken. It was determined that as a result of artificial aging, α-AlFeMnSi intermetallic phase precipitation were formed between α-Al grains. By the effect of precipitation hardening, an increase in hardness was observed in all artificially aged samples; the highest hardness was found as an average of 149.3 HV in AA6013 samples aged artificially for 2 hours at 200 °C. A general decrease in the friction coefficients of samples aged at both 180 °C and 200 °C was observed along with the artificial aging temperature. The lowest specific wear rate was determined as 3.542x10-3 mm3/Nm in the AA6013 sample aged artificially for 2 hours at 200 °C.
- 1 June 2021
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 63 (6) , 512-518
Ballistic performance of powder metal Al5Cu-B4C composite as monolithic and laminated armor
In this study, ballistic performances of x wt.-% B4C (x = 5, 10, and 20) reinforced Al5Cu matrix composite samples were investigated as a monolithic and laminated composite armor component. Composite armor plates were produced by the powder metallurgy method. The prepared powders were pressed under 400 MPa pressing pressure. Green compacts were pre-sintered at 400 °C for 30 minutes in order to blow the lubricant. Subsequently, liquid phase sintering was performed at 610 °C for 210 minutes. In ballistic tests, 7.62 mm caliber armor-piercing bullets were used as the ballistic threat. In the ballistic tests of monolithic armors, only 10 mm thick powder metal composite plates were tested. In the ballistic tests of laminated composite armors, these powdered metal plates were layered with 10 mm thick alumina ceramic plate front layers and 10 mm thick AA5083 plates. Although all of the monolithic powder metal composite armors were penetrated, they showed multi-hit capability. All of the laminated composite armors provided full ballistic protection. It was determined that with the increase in B4C reinforcement rate, the ballistic resistance also increased due to the improvement in strength, hardness, and abrasive feature.
- 1 June 2021
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 63 (6) , 512-518
Ballistic performance of powder metal Al5Cu-B4C composite as monolithic and laminated armor
In this study, ballistic performances of x wt.-% B4C (x = 5, 10, and 20) reinforced Al5Cu matrix composite samples were investigated as a monolithic and laminated composite armor component. Composite armor plates were produced by the powder metallurgy method. The prepared powders were pressed under 400 MPa pressing pressure. Green compacts were pre-sintered at 400 °C for 30 minutes in order to blow the lubricant. Subsequently, liquid phase sintering was performed at 610 °C for 210 minutes. In ballistic tests, 7.62 mm caliber armor-piercing bullets were used as the ballistic threat. In the ballistic tests of monolithic armors, only 10 mm thick powder metal composite plates were tested. In the ballistic tests of laminated composite armors, these powdered metal plates were layered with 10 mm thick alumina ceramic plate front layers and 10 mm thick AA5083 plates. Although all of the monolithic powder metal composite armors were penetrated, they showed multi-hit capability. All of the laminated composite armors provided full ballistic protection. It was determined that with the increase in B4C reinforcement rate, the ballistic resistance also increased due to the improvement in strength, hardness, and abrasive feature.
- 1 April 2021
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 63 (4) , 350-355
Mechanical properties of Al-Cu/B4C and Al-Mg/B4C metal matrix composites
To be able to successfully produce ceramic-reinforced aluminum matrix composites by using the powder metallurgy method, the wetting of ceramic reinforcements should be increased. In addition, the negative effects of the oxide layer of the aluminum matrix on sinterability should be minimized. In order to break the oxide layer, the deoxidation property of Mg can be used. Furthermore, by creating a liquid phase, both wettability and sinterability can be improved. In this study, the effects of Mg and Cu alloy elements and sintering phase on the wettability, sinterability, and mechanical properties of Al/B4C composites were investigated. For this purpose, various amounts (5, 10, 20, and 30 wt.-%) of B4C reinforced Al5Cu and Al5Mg matrix composites were produced by the powder metallurgy method. After pressing under 400 MPa pressure, composite samples were sintered for 4 hours. The sintering was carried out in two different groups as solid phase sintering at 560 °C and liquid phase sintering at 610 °C. Despite the deoxidation effect of Mg in Al5Mg matrix composites, higher mechanical properties were determined in Al5Cu composites which were sintered in liquid phase because wettability increased. The highest mechanical properties were obtained in the 20 wt.-% B4C reinforced Al5Cu sample sintered in liquid phase.
- 1 April 2021
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 63 (4) , 350-355
Mechanical properties of Al-Cu/B4C and Al-Mg/B4C metal matrix composites
To be able to successfully produce ceramic-reinforced aluminum matrix composites by using the powder metallurgy method, the wetting of ceramic reinforcements should be increased. In addition, the negative effects of the oxide layer of the aluminum matrix on sinterability should be minimized. In order to break the oxide layer, the deoxidation property of Mg can be used. Furthermore, by creating a liquid phase, both wettability and sinterability can be improved. In this study, the effects of Mg and Cu alloy elements and sintering phase on the wettability, sinterability, and mechanical properties of Al/B4C composites were investigated. For this purpose, various amounts (5, 10, 20, and 30 wt.-%) of B4C reinforced Al5Cu and Al5Mg matrix composites were produced by the powder metallurgy method. After pressing under 400 MPa pressure, composite samples were sintered for 4 hours. The sintering was carried out in two different groups as solid phase sintering at 560 °C and liquid phase sintering at 610 °C. Despite the deoxidation effect of Mg in Al5Mg matrix composites, higher mechanical properties were determined in Al5Cu composites which were sintered in liquid phase because wettability increased. The highest mechanical properties were obtained in the 20 wt.-% B4C reinforced Al5Cu sample sintered in liquid phase.
- 25 March 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 74 (6) , 1397-1408
Microstructure and Dry Sliding Wear Behaviors of Microwave-Sintered Al-4.4Cu-0.7 Mg-0.6Si-B4C/nGr Hybrid Composites
- 25 March 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 74 (6) , 1397-1408
Microstructure and Dry Sliding Wear Behaviors of Microwave-Sintered Al-4.4Cu-0.7 Mg-0.6Si-B4C/nGr Hybrid Composites