Francois R. Charron
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Francois R. Charron has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Cederick Landry
Department of Mechanical Engineering, Université de Sherbrooke, Sherbrooke, Canada
2 shared publications - Jean-Sébastien Plante
Faculté de Genie, Université de Sherbrooke, 2500 boul. de l'Université, Sherbrooke, QC J1K 2R1, Canada
2 shared publications - Mathieu Picard
Faculté de Génie, Université de Sherbrooke, 3000 boul. de l'Université, Sherbrooke, QC J1K 0A5, Canada
2 shared publications - Patrick K. Dubois
Institut Interdisciplinaire D'innovation Technologique, Université de Sherbrooke, 3000 boul. de l'Université, Sherbrooke, QC J1K 0A5, Canada
2 shared publications
Latest Publications
- 13 August 2018
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 141 (1)
Design Space Exploration of a Beam Flexible Hub Concept for an Inside-Out Ceramic Turbine Using a Simplified Rotordynamic Finite Element Model
This paper presents a new flexible hub design for the inside-out ceramic turbine (ICT) rotor configuration. This configuration is used in microturbines to integrate ceramic blades in order to increase turbine inlet temperature (TIT), which leads to higher cycle efficiency values. The ICT uses an outer composite rim to load the ceramic blades in compression by converting the centrifugal loads of the blades into hoop stresses in the composite rim. High stresses in the composite rim lead to high radial displacement of the blades. This displacement is compensated by using flexible hub in order to maintain the contact with the blades. However, hub flexibility can lead to rotordynamic problems as heavy hub deformation will induce high stresses in it. Thus, stresses in the hub are induced by both rotordynamics and centrifugation, requiring a multi-objective design process, which has yielded geometries that limited, until now, the blade tip speed to 358 m/s. In this paper, a simplified rotordynamics finite element model of a flexible hub is developed to allow quick design iterations. Using the model, a design space exploration of this hub concept is done while considering centrifugation and rotordynamics. Experimental validation is conducted on a simplified ICT prototype up to 129 krpm, i.e., an equivalent blade tip speed of 390 m/s. Finally, predictions from the experimentally calibrated model show that the tested prototype hub could reach a blade tip speed of 680 m/s.
- 13 August 2018
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 141 (1)
Design Space Exploration of a Beam Flexible Hub Concept for an Inside-Out Ceramic Turbine Using a Simplified Rotordynamic Finite Element Model
This paper presents a new flexible hub design for the inside-out ceramic turbine (ICT) rotor configuration. This configuration is used in microturbines to integrate ceramic blades in order to increase turbine inlet temperature (TIT), which leads to higher cycle efficiency values. The ICT uses an outer composite rim to load the ceramic blades in compression by converting the centrifugal loads of the blades into hoop stresses in the composite rim. High stresses in the composite rim lead to high radial displacement of the blades. This displacement is compensated by using flexible hub in order to maintain the contact with the blades. However, hub flexibility can lead to rotordynamic problems as heavy hub deformation will induce high stresses in it. Thus, stresses in the hub are induced by both rotordynamics and centrifugation, requiring a multi-objective design process, which has yielded geometries that limited, until now, the blade tip speed to 358 m/s. In this paper, a simplified rotordynamics finite element model of a flexible hub is developed to allow quick design iterations. Using the model, a design space exploration of this hub concept is done while considering centrifugation and rotordynamics. Experimental validation is conducted on a simplified ICT prototype up to 129 krpm, i.e., an equivalent blade tip speed of 390 m/s. Finally, predictions from the experimentally calibrated model show that the tested prototype hub could reach a blade tip speed of 680 m/s.
- 29 September 2017
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 140 (1) , 011013
Rotordynamics of a Highly Flexible Hub for Inside-Out Ceramic Turbine Application: Finite Element Modeling and Experimental Validation
The inside-out ceramic turbine (ICT) is a promising concept to increase turbine inlet temperatures in microturbines by integrating individual monolithic ceramic. This architecture uses a carbon–polymer composite rim to support the blades mainly in compression. High tangential velocities lead to elevated radial displacement of the rim, and therefore, the rotor hub needs to have sufficient compliance to follow this radial displacement. However, the rotordynamics of a flexible hub is not widely understood. This paper presents the rotordynamic analysis of a highly flexible hub for an ICT architecture. Finite element modeling (FEM) is used to design a simplified turbine prototype that maximizes the hub flexibility to explore the limits of the concept. The rotordynamics behavior of the highly flexible hub is measured by spinning a 171-mm diameter prototype up to 49 krpm. This paper highlights three principal challenges of this particular rotordynamics. First, critical speeds mode shape becomes highly coupled with bearings displacement, shaft bending, and hub deformation. At high-speed, the hub deforms out of phase with the shaft, which can cause high stresses in the hub. Second, the angular position between unbalance masses of the flexible hub and the composite rim changes the unbalance response significantly. Finally, vibration causes high stresses in the hub, due to the relative displacement between the composite rim and the shaft, which could lead to failure of the hub. Nevertheless, the rotordynamics of an ICT configuration is manageable as long as the vibration-induced stress in the hub is kept under its limit.
- 29 September 2017
- Published by ASME International in Journal of Vibration and Acoustics
- Vol. 140 (1) , 011013
Rotordynamics of a Highly Flexible Hub for Inside-Out Ceramic Turbine Application: Finite Element Modeling and Experimental Validation
The inside-out ceramic turbine (ICT) is a promising concept to increase turbine inlet temperatures in microturbines by integrating individual monolithic ceramic. This architecture uses a carbon–polymer composite rim to support the blades mainly in compression. High tangential velocities lead to elevated radial displacement of the rim, and therefore, the rotor hub needs to have sufficient compliance to follow this radial displacement. However, the rotordynamics of a flexible hub is not widely understood. This paper presents the rotordynamic analysis of a highly flexible hub for an ICT architecture. Finite element modeling (FEM) is used to design a simplified turbine prototype that maximizes the hub flexibility to explore the limits of the concept. The rotordynamics behavior of the highly flexible hub is measured by spinning a 171-mm diameter prototype up to 49 krpm. This paper highlights three principal challenges of this particular rotordynamics. First, critical speeds mode shape becomes highly coupled with bearings displacement, shaft bending, and hub deformation. At high-speed, the hub deforms out of phase with the shaft, which can cause high stresses in the hub. Second, the angular position between unbalance masses of the flexible hub and the composite rim changes the unbalance response significantly. Finally, vibration causes high stresses in the hub, due to the relative displacement between the composite rim and the shaft, which could lead to failure of the hub. Nevertheless, the rotordynamics of an ICT configuration is manageable as long as the vibration-induced stress in the hub is kept under its limit.