Richard J. Kerekes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Richard J. Kerekes has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Christer Sandberg
Holmen AB , 601 88 Norrköping , Sweden
1 shared publication - Frank Meltzer
Canfor Pulp Ltd. , now with Mercer Pulp Products , Charlottenstraße 59 , 10117 Berlin , Germany
1 shared publication J. David McDonald
JDMcD Consulting Inc.,CANADA
1 shared publication- J. David McDonald
JDMcD Consulting Inc
1 shared publication
Latest Publications
- Open Access
- 19 November 2024
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 40 (1) , 107-112
Energy consumption in refiner mechanical pulping
The efficiency of mechanical pulping has long been of interest due to the large energy consumed by the process. Previous estimates of theoretical efficiency have accounted for less than 20 % of the energy employed. In this study, we make new estimates based on fracture mechanics and abrasion as the mechanisms of new surface creation. We postulate that fracture mechanics comminutes wood into fibres and creates pores in fibre walls. This consumes around 100 kWh/t. Abrasion peels surface material from fibres in the form of morphologically different fines particles. Based on abrasion theory, we estimate this specific energy to be around 1,330 kWh/t. Together, fracture mechanics and abrasion, account for about 70 % of the specific energy (2,000 kWh/t) to produce TMP for printing paper grades. We postulate that the remaining energy is consumed as hysteresis losses from viscoelastic strains not linked to creation of new surface. The largest single source of energy consumption, abrasion, alone accounts for about 66 % of the energy of the process. Finally, we discuss how energy may be reduced by refining intensity and other means.
- 19 November 2024
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 40 (1) , 107-112
Open AccessEnergy consumption in refiner mechanical pulping
The efficiency of mechanical pulping has long been of interest due to the large energy consumed by the process. Previous estimates of theoretical efficiency have accounted for less than 20 % of the energy employed. In this study, we make new estimates based on fracture mechanics and abrasion as the mechanisms of new surface creation. We postulate that fracture mechanics comminutes wood into fibres and creates pores in fibre walls. This consumes around 100 kWh/t. Abrasion peels surface material from fibres in the form of morphologically different fines particles. Based on abrasion theory, we estimate this specific energy to be around 1,330 kWh/t. Together, fracture mechanics and abrasion, account for about 70 % of the specific energy (2,000 kWh/t) to produce TMP for printing paper grades. We postulate that the remaining energy is consumed as hysteresis losses from viscoelastic strains not linked to creation of new surface. The largest single source of energy consumption, abrasion, alone accounts for about 66 % of the energy of the process. Finally, we discuss how energy may be reduced by refining intensity and other means.
- 11 September 2021
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 36 (4) , 714-717
Bar forces in pulp refiners
Refiners develop pulp properties by applying forces on fibres during bar crossings. The size of these forces is critical in developing fibre properties while avoiding fibre shortening. This study has shown that bar force calculated from Specific Edge load (SEL) gives the same result as vector-based derivations of average bar force. Predicted forces agree reasonably well with ones measured by a novel piezo-electric sensor in refiner bars and forces estimated from measurements of fibre shortening.
- 11 September 2021
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 36 (4) , 714-717
Bar forces in pulp refiners
Refiners develop pulp properties by applying forces on fibres during bar crossings. The size of these forces is critical in developing fibre properties while avoiding fibre shortening. This study has shown that bar force calculated from Specific Edge load (SEL) gives the same result as vector-based derivations of average bar force. Predicted forces agree reasonably well with ones measured by a novel piezo-electric sensor in refiner bars and forces estimated from measurements of fibre shortening.
- 7 August 2018
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 33 (3) , 580
Corrigendum to: The influence of bar width on bar forces and fibre shortening in low consistency pulp refining
- 7 August 2018
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 33 (3) , 580
Corrigendum to: The influence of bar width on bar forces and fibre shortening in low consistency pulp refining
- Open Access
- 1 July 2018
- Published by Tsinghua University Press in Paper and Biomaterials
- Vol. 3 (3) , 1-6
Fibre Treatment Uniformity in Pulp Refining
This paper explores implications of previous work which suggested that pulp refining is achieved by a small number of impacts.As a consequence, the purpose of multiple bar crossings in refiners is to expose many fibres to a few effective cycles, not to impose many cycles on each fibre.Based on this postulate, tensile strength increase was found to be well described by a cumulative probability equation having two parameters: (a) number of bar crossings and (b) probability of a successful refining outcome at each crossing.In this paper, this concept further with additional refiner data was explored and the link between the probability term and measurable refiner variables was examined.By proposing the possibility, these two parameters may be a desirable alternative to specific energy and specific edge load for characterizing refining action.
- 1 July 2018
- Published by Tsinghua University Press in Paper and Biomaterials
- Vol. 3 (3) , 1-6
Open AccessFibre Treatment Uniformity in Pulp Refining
This paper explores implications of previous work which suggested that pulp refining is achieved by a small number of impacts.As a consequence, the purpose of multiple bar crossings in refiners is to expose many fibres to a few effective cycles, not to impose many cycles on each fibre.Based on this postulate, tensile strength increase was found to be well described by a cumulative probability equation having two parameters: (a) number of bar crossings and (b) probability of a successful refining outcome at each crossing.In this paper, this concept further with additional refiner data was explored and the link between the probability term and measurable refiner variables was examined.By proposing the possibility, these two parameters may be a desirable alternative to specific energy and specific edge load for characterizing refining action.
- Open Access
- 5 August 2015
- Published by BioResources in BioResources
- Vol. 10 (4) , 8795-8811
Perspectives on High and Low Consistency Refining in Mechanical Pulping
Perspectives on High and Low Consistency Refining in Mechanical Pulping
- 5 August 2015
- Published by BioResources in BioResources
- Vol. 10 (4) , 8795-8811
Open AccessPerspectives on High and Low Consistency Refining in Mechanical Pulping
Perspectives on High and Low Consistency Refining in Mechanical Pulping