Thomas O. Jelly
Research Subjects
Thomas O. Jelly has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Angela Busse
University of Glasgow
6 shared publications - Richard D. Sandberg
Department of Mechanical Engineering, University of Melbourne, Parkville, VIC 3010, Australia
4 shared publications - Massimiliano Nardini
University of Melbourne Department of Mechanical Engineering
3 shared publications - Nicholas Hutchins
University of Melbourne
3 shared publications - Daniel Chung
University of Melbourne
2 shared publications - Greg Sluyter
GE Aerospace
2 shared publications
Latest Publications
- Open Access
- 20 June 2025
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 116
Impact of windward and effective slope on the roughness effect of ratchet-type surfaces in turbulent channel flow
- 20 June 2025
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 116
Open AccessImpact of windward and effective slope on the roughness effect of ratchet-type surfaces in turbulent channel flow
- Open Access
- 20 December 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (5) , 1-12
Effects of Localized Non-Gaussian Roughness on High-Pressure Turbine Aerothermal Performance: Convective Heat Transfer, Skin Friction, and the Reynolds’ Analogy
Compressible direct numerical simulations are conducted to investigate how surface roughness affects the aerothermal performance of a high-pressure turbine vane operating at an exit Reynolds number of 0.59 ×106 and exit Mach number of 0.92. The roughness under investigation here was synthesized with non-Gaussian statistical properties and an amplitude that varies over its chord length, representative of what truly occurs on an in-service vane. Particular attention is directed toward how systematically changing the axial extent of leading edge roughness affects convective heat transfer (Nusselt and Stanton numbers) and aerodynamic drag (skin friction coefficient) on the pressure and suction surfaces. The results of this investigation demonstrate that moving the larger amplitude roughness further along the suction surface can alter the blade boundary layer state. In fact, toward the trailing edge of one of the rough vanes investigated here, the local skin friction coefficient increases by a factor of 22 compared to smooth-vane levels, whereas the local Nusselt number increases by a factor 6. The disproportionate rise of drag compared to heat transfer is explored in further detail by quantifying the Reynolds’ analogy and by calculating the fractional contributions of pressure drag and viscous drag to the total drag force. The effect of varying the inlet turbulence intensity and integral length scale for a fixed roughness topography is also investigated, and the Reynolds number scaling of heat transfer and drag is examined in the context of the Chilton–Colburn analogy.
- 20 December 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (5) , 1-12
Open AccessEffects of Localized Non-Gaussian Roughness on High-Pressure Turbine Aerothermal Performance: Convective Heat Transfer, Skin Friction, and the Reynolds’ Analogy
Compressible direct numerical simulations are conducted to investigate how surface roughness affects the aerothermal performance of a high-pressure turbine vane operating at an exit Reynolds number of 0.59 ×106 and exit Mach number of 0.92. The roughness under investigation here was synthesized with non-Gaussian statistical properties and an amplitude that varies over its chord length, representative of what truly occurs on an in-service vane. Particular attention is directed toward how systematically changing the axial extent of leading edge roughness affects convective heat transfer (Nusselt and Stanton numbers) and aerodynamic drag (skin friction coefficient) on the pressure and suction surfaces. The results of this investigation demonstrate that moving the larger amplitude roughness further along the suction surface can alter the blade boundary layer state. In fact, toward the trailing edge of one of the rough vanes investigated here, the local skin friction coefficient increases by a factor of 22 compared to smooth-vane levels, whereas the local Nusselt number increases by a factor 6. The disproportionate rise of drag compared to heat transfer is explored in further detail by quantifying the Reynolds’ analogy and by calculating the fractional contributions of pressure drag and viscous drag to the total drag force. The effect of varying the inlet turbulence intensity and integral length scale for a fixed roughness topography is also investigated, and the Reynolds number scaling of heat transfer and drag is examined in the context of the Chilton–Colburn analogy.
- Open Access
- 11 January 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 979
Modelling the effect of roughness density on turbulent forced convection
By examining a systematic set of direct numerical simulations, we develop a model which captures the effect of roughness density on global and local heat transfer in forced convection. The surfaces considered are zero-skewed three-dimensional sinusoidal rough walls with solidities, $\varLambda$ (defined as the frontal area divided by the total plan area), ranging from low $\varLambda = 0.09$ , medium $\varLambda = 0.18$ to high $\varLambda = 0.36$ . For each solidity, we vary the roughness height characterised by the roughness Reynolds number, $k^+$ , from transitionally rough to fully rough conditions. The findings indicate that, as the fully rough regime is approached, there is a pronounced breakdown in the analogy between heat and momentum transfer, whereby the velocity roughness function $\Delta U^+$ continues to increase and the temperature roughness function $\Delta \varTheta ^+$ attains a peak with increasing $k^+$ . This breakdown occurs at higher sand-grain roughness Reynolds numbers ( $k_s^+$ ) with increasing solidity. Locally, we find that the heat transfer can be meaningfully partitioned into two categories: exposed, high-shear regions experiencing higher heat transfer obeying a local Reynolds analogy and sheltered, reversed-flow regions experiencing lower and spatially uniform heat transfer. The relative contribution of these distinct mechanisms to the global heat transfer depends on the fraction of the total surface area covered by these regions, which ultimately depends on $\varLambda$ . These insights enable us to develop a model for the rough-wall heat-transfer coefficient, ${C_{h,k}(k^+, \varLambda, Pr)}$ , where $Pr$ is the molecular Prandtl number, that assumes different heat-transfer laws in exposed and sheltered regions. We show that the exposed–sheltered surface-area fractions can be modelled through simple ray tracing that is solely dependent on the surface topography and a prescribed sheltering angle. Model predictions compare well when applied to heat-transfer data of traverse ribs from the literature.- 11 January 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 979
Open AccessModelling the effect of roughness density on turbulent forced convection
By examining a systematic set of direct numerical simulations, we develop a model which captures the effect of roughness density on global and local heat transfer in forced convection. The surfaces considered are zero-skewed three-dimensional sinusoidal rough walls with solidities, $\varLambda$ (defined as the frontal area divided by the total plan area), ranging from low $\varLambda = 0.09$ , medium $\varLambda = 0.18$ to high $\varLambda = 0.36$ . For each solidity, we vary the roughness height characterised by the roughness Reynolds number, $k^+$ , from transitionally rough to fully rough conditions. The findings indicate that, as the fully rough regime is approached, there is a pronounced breakdown in the analogy between heat and momentum transfer, whereby the velocity roughness function $\Delta U^+$ continues to increase and the temperature roughness function $\Delta \varTheta ^+$ attains a peak with increasing $k^+$ . This breakdown occurs at higher sand-grain roughness Reynolds numbers ( $k_s^+$ ) with increasing solidity. Locally, we find that the heat transfer can be meaningfully partitioned into two categories: exposed, high-shear regions experiencing higher heat transfer obeying a local Reynolds analogy and sheltered, reversed-flow regions experiencing lower and spatially uniform heat transfer. The relative contribution of these distinct mechanisms to the global heat transfer depends on the fraction of the total surface area covered by these regions, which ultimately depends on $\varLambda$ . These insights enable us to develop a model for the rough-wall heat-transfer coefficient, ${C_{h,k}(k^+, \varLambda, Pr)}$ , where $Pr$ is the molecular Prandtl number, that assumes different heat-transfer laws in exposed and sheltered regions. We show that the exposed–sheltered surface-area fractions can be modelled through simple ray tracing that is solely dependent on the surface topography and a prescribed sheltering angle. Model predictions compare well when applied to heat-transfer data of traverse ribs from the literature. - 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-29
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part II: The Effect of Roughness on the Performance of a High-Pressure Turbine Blade
Turbine blades generally present surface roughness introduced in the manufacturing process or caused by in-service degradation, which can have a significant impact on aero-thermal performance. A better understanding of the fundamental physical mechanisms arising from the interaction between the roughness and the turbine flow at engine-relevant conditions can provide insights for the design of blades with improved efficiency and longer operational life. To this end, a high-fidelity numerical framework combining a well-validated solver for direct numerical simulation and a second-order accurate immersed boundary method is employed to predict roughness-induced aero-thermal effects on an LS89 high-pressure turbine (HPT) blade at engine-relevant conditions. Different amplitudes and distributions of surface roughness are investigated and a reference smooth-blade simulation under the same flow conditions is conducted for comparison. Roughness of increasing amplitude progressively shifts the blade suction side boundary layer transition upstream, producing larger values of the turbulent kinetic energy and higher total wake losses. The on-surface data-capturing capabilities of the numerical framework provide direct measurements of the heat flux and the skin friction coefficient, hence offering quantitative information between the surface topology and engineering-relevant performance parameters. This work may provide a benchmark for future numerical studies of turbomachinery flows with roughness.
- 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-29
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part II: The Effect of Roughness on the Performance of a High-Pressure Turbine Blade
Turbine blades generally present surface roughness introduced in the manufacturing process or caused by in-service degradation, which can have a significant impact on aero-thermal performance. A better understanding of the fundamental physical mechanisms arising from the interaction between the roughness and the turbine flow at engine-relevant conditions can provide insights for the design of blades with improved efficiency and longer operational life. To this end, a high-fidelity numerical framework combining a well-validated solver for direct numerical simulation and a second-order accurate immersed boundary method is employed to predict roughness-induced aero-thermal effects on an LS89 high-pressure turbine (HPT) blade at engine-relevant conditions. Different amplitudes and distributions of surface roughness are investigated and a reference smooth-blade simulation under the same flow conditions is conducted for comparison. Roughness of increasing amplitude progressively shifts the blade suction side boundary layer transition upstream, producing larger values of the turbulent kinetic energy and higher total wake losses. The on-surface data-capturing capabilities of the numerical framework provide direct measurements of the heat flux and the skin friction coefficient, hence offering quantitative information between the surface topology and engineering-relevant performance parameters. This work may provide a benchmark for future numerical studies of turbomachinery flows with roughness.
- 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-37
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part I: Methodology and Challenges
High-fidelity simulation of transitional and turbulent flows over multi-scale surface roughness presents several challenges. For instance, the complex and irregular geometrical nature of surface roughness makes it impractical to employ conforming structured grids, commonly adopted in large-scale numerical simulations due to their high computational efficiency. One possible solution to overcome this problem is offered by immersed boundary methods, which allow wall boundary conditions to be enforced on grids that do not conform to the geometry of the solid boundary. To this end, a three-dimensional, second-order accurate boundary data immersion method (BDIM) is adopted. A novel mapping algorithm that can be applied to general three-dimensional surfaces is presented, together with a newly developed data-capturing methodology to extract and analyze on-surface flow quantities of interest. A rigorous procedure to compute gradient quantities such as the wall shear stress and the heat flux on complex non-conforming geometries is also introduced. The new framework is validated by performing a direct numerical simulation (DNS) of fully developed turbulent channel flow over sinusoidal egg-carton roughness in a minimal-span domain. For this canonical case, the averaged streamwise velocity profiles are compared against results from the literature obtained with a body-fitted grid. General guidelines on the BDIM resolution requirements for multi-scale roughness simulation are given. Momentum and energy balance methods are used to validate the calculation of the overall skin friction and heat transfer at the wall. The BDIM is then employed to investigate the effect of irregular homogeneous surface roughness on the performance of an LS-89 high-pressure turbine blade at engine-relevant conditions using DNS. This is the first application of the BDIM to realize multi-scale roughness for transitional flow in transonic conditions in the context of high-pressure turbines. The methodology adopted to generate the desired roughness distribution and to apply it to the reference blade geometry is introduced. The results are compared to the case of an equivalent smooth blade.
- 4 December 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (3) , 1-37
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part I: Methodology and Challenges
High-fidelity simulation of transitional and turbulent flows over multi-scale surface roughness presents several challenges. For instance, the complex and irregular geometrical nature of surface roughness makes it impractical to employ conforming structured grids, commonly adopted in large-scale numerical simulations due to their high computational efficiency. One possible solution to overcome this problem is offered by immersed boundary methods, which allow wall boundary conditions to be enforced on grids that do not conform to the geometry of the solid boundary. To this end, a three-dimensional, second-order accurate boundary data immersion method (BDIM) is adopted. A novel mapping algorithm that can be applied to general three-dimensional surfaces is presented, together with a newly developed data-capturing methodology to extract and analyze on-surface flow quantities of interest. A rigorous procedure to compute gradient quantities such as the wall shear stress and the heat flux on complex non-conforming geometries is also introduced. The new framework is validated by performing a direct numerical simulation (DNS) of fully developed turbulent channel flow over sinusoidal egg-carton roughness in a minimal-span domain. For this canonical case, the averaged streamwise velocity profiles are compared against results from the literature obtained with a body-fitted grid. General guidelines on the BDIM resolution requirements for multi-scale roughness simulation are given. Momentum and energy balance methods are used to validate the calculation of the overall skin friction and heat transfer at the wall. The BDIM is then employed to investigate the effect of irregular homogeneous surface roughness on the performance of an LS-89 high-pressure turbine blade at engine-relevant conditions using DNS. This is the first application of the BDIM to realize multi-scale roughness for transitional flow in transonic conditions in the context of high-pressure turbines. The methodology adopted to generate the desired roughness distribution and to apply it to the reference blade geometry is introduced. The results are compared to the case of an equivalent smooth blade.
- Open Access
- 26 September 2023
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 112 (1) , 105-128
Influence of Ridge Spacing, Ridge Width, and Reynolds Number on Secondary Currents in Turbulent Channel Flow Over Triangular Ridges
Most studies of secondary currents (SCs) over streamwise aligned ridges have been performed for rectangular ridge cross-sections. In this study, secondary currents above triangular ridges are systematically studied using direct numerical simulations of turbulent channel flow. The influence of ridge spacing on flow topology, mean flow, and turbulence statistics is investigated at two friction Reynolds numbers, 550 and 1000. In addition, the effects of ridge width on SCs, which have not previously been considered for this ridge shape, are explored. The influence of SCs on shear stress statistics increases with increased ridge spacing until SCs fill the entire channel. One of the primary findings is that, for ridge configurations with pronounced secondary currents, shear stress statistics exhibit clear Reynolds number sensitivity with a significant growth of dispersive shear stress levels with Reynolds number. In contrast to rectangular ridges, no above-ridge tertiary flows are observed for the tested range of ridge widths. Flow visualisations of SCs reveal the existence of corner vortices that form at the intersection of the lateral ridge sides and the smooth-wall sections. These are found to gradually disappear as ridges increase in width. Premultiplied spectra of streamwise velocity fluctuations show strong dependency on the spanwise sampling location. Whereas spanwise averaged spectra show no strong modifications by SCs, a significant increase of energy levels emerges at higher wavelengths for spectra sampled at the spanwise locations that correspond to the centres of the secondary currents.
- 26 September 2023
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 112 (1) , 105-128
Open AccessInfluence of Ridge Spacing, Ridge Width, and Reynolds Number on Secondary Currents in Turbulent Channel Flow Over Triangular Ridges
Most studies of secondary currents (SCs) over streamwise aligned ridges have been performed for rectangular ridge cross-sections. In this study, secondary currents above triangular ridges are systematically studied using direct numerical simulations of turbulent channel flow. The influence of ridge spacing on flow topology, mean flow, and turbulence statistics is investigated at two friction Reynolds numbers, 550 and 1000. In addition, the effects of ridge width on SCs, which have not previously been considered for this ridge shape, are explored. The influence of SCs on shear stress statistics increases with increased ridge spacing until SCs fill the entire channel. One of the primary findings is that, for ridge configurations with pronounced secondary currents, shear stress statistics exhibit clear Reynolds number sensitivity with a significant growth of dispersive shear stress levels with Reynolds number. In contrast to rectangular ridges, no above-ridge tertiary flows are observed for the tested range of ridge widths. Flow visualisations of SCs reveal the existence of corner vortices that form at the intersection of the lateral ridge sides and the smooth-wall sections. These are found to gradually disappear as ridges increase in width. Premultiplied spectra of streamwise velocity fluctuations show strong dependency on the spanwise sampling location. Whereas spanwise averaged spectra show no strong modifications by SCs, a significant increase of energy levels emerges at higher wavelengths for spectra sampled at the spanwise locations that correspond to the centres of the secondary currents.
- 14 September 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (11) , 1-17
High-Fidelity Computational Assessment of Aero-Thermal Performance and the Reynolds’ Analogy for Additively Manufactured Anisotropic Surface Roughness
Direct numerical simulations of incompressible turbulent forced convection over irregular, anisotropic surface roughness in a pressure-driven plane channel flow have been performed. Heat transfer was simulated by solving the passive scalar transport equation with Prandtl number Pr = 0.7. The roughness topographies under investigation here are based on an X-ray computed tomography scan of an additively manufactured internal cooling passage, which had an irregular, multiscale and mildly non-Gaussian height distribution. Three different roughness topographies and three different friction Reynolds numbers (Reτ = 395, 590, 720) were considered, along with reference smooth-wall simulations at matched Reτ. By systematically varying the roughness topography and flow conditions, a direct computational assessment of aero-thermal performance (pressure losses and heat transfer) and the Reynolds analogy factor, i.e., 2Ch/Cf, where Ch is the heat-transfer coefficient (Stanton number) and Cf is the skin-friction coefficient, was conducted. The results highlight the profound impact that the roughness orientation (relative to the flow direction) has upon the aero-thermal performance of additively manufactured internal passages, with transverse-aligned roughness augmenting heat transfer by as much as 33%, relative to its streamwise-aligned counterpart. An interrogation of velocity and temperature statistics in the near-wall region was also performed, which underlined the growing dissimilarity between heat transfer and drag as fully rough conditions are approached.
- 14 September 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (11) , 1-17
High-Fidelity Computational Assessment of Aero-Thermal Performance and the Reynolds’ Analogy for Additively Manufactured Anisotropic Surface Roughness
Direct numerical simulations of incompressible turbulent forced convection over irregular, anisotropic surface roughness in a pressure-driven plane channel flow have been performed. Heat transfer was simulated by solving the passive scalar transport equation with Prandtl number Pr = 0.7. The roughness topographies under investigation here are based on an X-ray computed tomography scan of an additively manufactured internal cooling passage, which had an irregular, multiscale and mildly non-Gaussian height distribution. Three different roughness topographies and three different friction Reynolds numbers (Reτ = 395, 590, 720) were considered, along with reference smooth-wall simulations at matched Reτ. By systematically varying the roughness topography and flow conditions, a direct computational assessment of aero-thermal performance (pressure losses and heat transfer) and the Reynolds analogy factor, i.e., 2Ch/Cf, where Ch is the heat-transfer coefficient (Stanton number) and Cf is the skin-friction coefficient, was conducted. The results highlight the profound impact that the roughness orientation (relative to the flow direction) has upon the aero-thermal performance of additively manufactured internal passages, with transverse-aligned roughness augmenting heat transfer by as much as 33%, relative to its streamwise-aligned counterpart. An interrogation of velocity and temperature statistics in the near-wall region was also performed, which underlined the growing dissimilarity between heat transfer and drag as fully rough conditions are approached.
- Open Access
- 31 March 2023
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 101
High-fidelity computational study of roughness effects on high pressure turbine performance and heat transfer
- 31 March 2023
- Published by Elsevier in International Journal of Heat and Fluid Flow
- Vol. 101
Open AccessHigh-fidelity computational study of roughness effects on high pressure turbine performance and heat transfer
- Open Access
- 1 February 2023
- Published by Taylor & Francis in Journal of Turbulence
- Vol. 24 (1-2) , 57-81
Effect of high skewness and kurtosis on turbulent channel flow over irregular rough walls
The skewness of the roughness height distribution is one of the key topographical parameters that govern roughness effects on wall-bounded turbulence. In this paper mathematical bounds for realisable values of skewness and kurtosis are discussed in the context of irregular multi-scale rough surfaces, which are representative of typical forms of engineering roughness. The properties of a set of irregular rough surfaces fully covered by roughness features with very high positive and negative skewness and high kurtosis are investigated using direct numerical simulations of turbulent channel flow at . While an increase of the roughness function is observed at moderate skewness values in line with empirical predictions and previous results for moderately skewed surfaces, the roughness function saturates at extreme values of skewness. Overall, the roughness effect is found to be more sensitive to skewness over the negative skewness range compared to the positive skewness range. Surface pressure statistics show that for surfaces with extreme skewness fully covered by roughness features extreme pits or peaks do not dominate the roughness effect and that surrounding roughness features (‘background’ roughness) retain a significant influence. This is because, while extreme roughness features emerge as skewness approaches high positive or negative values, they tend to be sparse decreasing their overall impact on the wall-bounded flow.- 1 February 2023
- Published by Taylor & Francis in Journal of Turbulence
- Vol. 24 (1-2) , 57-81
Open AccessEffect of high skewness and kurtosis on turbulent channel flow over irregular rough walls
The skewness of the roughness height distribution is one of the key topographical parameters that govern roughness effects on wall-bounded turbulence. In this paper mathematical bounds for realisable values of skewness and kurtosis are discussed in the context of irregular multi-scale rough surfaces, which are representative of typical forms of engineering roughness. The properties of a set of irregular rough surfaces fully covered by roughness features with very high positive and negative skewness and high kurtosis are investigated using direct numerical simulations of turbulent channel flow at . While an increase of the roughness function is observed at moderate skewness values in line with empirical predictions and previous results for moderately skewed surfaces, the roughness function saturates at extreme values of skewness. Overall, the roughness effect is found to be more sensitive to skewness over the negative skewness range compared to the positive skewness range. Surface pressure statistics show that for surfaces with extreme skewness fully covered by roughness features extreme pits or peaks do not dominate the roughness effect and that surrounding roughness features (‘background’ roughness) retain a significant influence. This is because, while extreme roughness features emerge as skewness approaches high positive or negative values, they tend to be sparse decreasing their overall impact on the wall-bounded flow. - Open Access
- 28 October 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 951, A1
Impact of spanwise effective slope upon rough-wall turbulent channel flow
Whereas streamwise effective slope ( $ES_{x}$ ) is accepted as a key topographical parameter in the context of rough-wall turbulent flows, the significance of its spanwise counterpart ( $ES_{y}$ ) remains largely unexplored. Here, the response of turbulent channel flow over irregular, three-dimensional rough walls with systematically varied values of $ES_{y}$ is studied using direct numerical simulation. All simulations were performed at a fixed friction Reynolds number 395, corresponding to a viscous-scaled roughness height $k^{+}\approx 65.8$ (where $k$ is the mean peak-to-valley height). A surface generation algorithm is used to synthesise a set of ten irregular surfaces with specified $ES_{y}$ for three different values of $ES_{x}$ . All surfaces share a common mean peak-to-valley height and are near-Gaussian, which allows this study to focus on the impact of varying $ES_{y}$ , since roughness amplitude, skewness and $ES_{x}$ can be eliminated simultaneously as parameters. Based on an analysis of first- and second-order velocity statistics, as well as turbulence co-spectra and the fractional contribution of pressure and viscous drag, the study shows that $ES_{y}$ can strongly affect the roughness drag penalty – particularly for low- $ES_{x}$ surfaces. A secondary observation is that particular low- $ES_{y}$ surfaces in this study can lead to diminished levels of outer-layer similarity in both mean flow and turbulence statistics, which is attributed to insufficient scale separation between the outer length scale and the in-plane spanwise roughness wavelength.- 28 October 2022
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 951, A1
Open AccessImpact of spanwise effective slope upon rough-wall turbulent channel flow
Whereas streamwise effective slope ( $ES_{x}$ ) is accepted as a key topographical parameter in the context of rough-wall turbulent flows, the significance of its spanwise counterpart ( $ES_{y}$ ) remains largely unexplored. Here, the response of turbulent channel flow over irregular, three-dimensional rough walls with systematically varied values of $ES_{y}$ is studied using direct numerical simulation. All simulations were performed at a fixed friction Reynolds number 395, corresponding to a viscous-scaled roughness height $k^{+}\approx 65.8$ (where $k$ is the mean peak-to-valley height). A surface generation algorithm is used to synthesise a set of ten irregular surfaces with specified $ES_{y}$ for three different values of $ES_{x}$ . All surfaces share a common mean peak-to-valley height and are near-Gaussian, which allows this study to focus on the impact of varying $ES_{y}$ , since roughness amplitude, skewness and $ES_{x}$ can be eliminated simultaneously as parameters. Based on an analysis of first- and second-order velocity statistics, as well as turbulence co-spectra and the fractional contribution of pressure and viscous drag, the study shows that $ES_{y}$ can strongly affect the roughness drag penalty – particularly for low- $ES_{x}$ surfaces. A secondary observation is that particular low- $ES_{y}$ surfaces in this study can lead to diminished levels of outer-layer similarity in both mean flow and turbulence statistics, which is attributed to insufficient scale separation between the outer length scale and the in-plane spanwise roughness wavelength.