APAbhay Patil

Abhay Patil

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Abhay Patil has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    An Experimental Investigation on the Erosion of a Helico-Axial Pump With Gas Presence

    by Yi Chen, Abhay Patil, Yiming Chen, Gerald Morrison, Marisela Rojas

    *Electrical submersible pump (ESP) technology has been widely applied in the oil and gas industry due to its high productivity. However, erosion always causes the reduction of productivity and sometimes even the failure of an ESP system. This study explores the effect of gas presence on erosion mechanism on an ESP which is composed of 4 stages of Helico-Axial Pump (HAP). A 200-hour

  • Effect of Leakage Flow Path Wear on Axial Thrust in Downhole Electrical Submersible Pump Unit

    by Abhay Patil, Marie Kasprzyk, Adolfo Delgado, Gerald Morrison

    Subsea production fluid is quite often characterized by the presence of frac sand, which causes wear within the pump, and alters the performance envelop. One of the design parameters critically affecting reliability is the thrust load generated by an impeller. The change in thrust load due to the erosion of the pump stages is not completely understood, and no relationship exists to foresee these reactive forces due to the complexity involved in predicting the flow characteristics. The purpose of this study is to understand the change in axial thrust due to commonly encountered wear mechanisms across the pump section especially wear across stage clearance seals. Based on in-house erosion testing of a mixed flow pump, three mesh models were built with each representing the pump condition at three different time intervals, namely, 0 h, 52 h, and 117 h of the total test time. The pump numerical models were validated using performance data collected from experimental testing. Axial thrust was found to increase with an increase in wear rate across stage seals. Since the increased clearance causes head degradation as well as an increase in thrust, the relationship of this head degradation is correlated with a change in thrust to further expand the affinity laws.


  • Experimental and Analytical Investigation of a Novel Multistage Twin-Screw Pump

    by P. Liu, G. Morrison, A. Patil

    The performance of a multistage electrical submersible twin-screw pump (ESTSP) was evaluated under different operating conditions. The effect of working fluid, differential pressure, gas volumetric fraction (GVF), and pump rotating speed on the behavior of the ESTSP has been studied. Mineral oil and water were selected as test liquids. The pump was tested with a maximum differential pressure of 1000 psig. The GVF varies from 0% to 85%. The flow rate capacity and the volumetric efficiency were investigated in this research. An existing model to predict leakage flow of the single stage twin-screw pump is improved by extending the application for the multistage pumps. The model shows good agreement with experimental data under various operating conditions.


  • Efficiency Prediction of Centrifugal Pump Using the Modified Affinity Laws

    by Rahul Agarwal, Abhay Patil, Gerald Morrison

    This research is a continuation of efforts aimed at establishing the modified affinity laws for viscosity to predict the pump performance directly from a plot in terms of dimensionless numbers, i.e., flow coefficient, Reynolds number, head coefficient, and efficiency. The group has earlier proposed modified head coefficient affinity law. This work proposes and validates a similar efficiency plot that completes the set of modified affinity laws that include all the input and output parameters for a specific pump design and type. A wide range of viscosities and flow rates are considered for CFD analysis to have a comprehensive set of data that includes enough data points to comment on both the laminar and turbulent flow cases categorized based on the hydraulic Reynolds number (2300). Initial analysis shows some inconsistency based on laminar versus turbulent simulation model selection which is addressed in the latter part of this work. In general, two curves can be constructed for laminar and turbulent flow cases. These curves have different axes parameters (exponents of the dimensionless numbers) depending on the plot being for a laminar or a turbulent flow case. Validation with established experimental data shows good agreement in terms of the variation of axes parameters (their exponents) depending on the pump type for a single suction impeller and a double suction impeller pump. The distinction between laminar and turbulent flow cases is found to be applicable to established experimental data as well.


  • Open Access

    Performance Evaluation and Dimensional Analysis of Multistage Helicoaxial Pump for Two-Phase Flow

    by Abhay Patil, Sujan Gudigopuram, Burak Ayyildiz, Adolfo Delgado, Gerald Morrison

    A four stage helicoaxial pump was tested under varying operating conditions. A range of inlet pressures, rotational speeds (3000, 3600 rpm), and gas void fractures (GVFs) were considered for two fluid viscosities. The head developed and power input to run the pump were recorded. Head, power input and efficiency decrease as the GVF increases with best efficiency point (BEP) moving towards lower flow rate conditions. Dimensional analysis was conducted to evaluate the applicability of current affinity laws to the two-phase flow performance of the pump under consideration. Dimensionless head coefficient and power coefficients were defined for two-phase flow, considering the homogeneity in the two-phase fluid properties. Deviations in the two-phase affinity coefficients from the common law curve increases with GVF. To bridge this gap, a new correlation is proposed with a revised flow coefficient that allows all the head coefficient data to collapse on a single line with a greater degree of accuracy.


  • Extending Classical Friction Loss Modeling to Predict the Viscous Performance of Pumping Devices

    by Abhay Patil, Wenjie Yin, Rahul Agarwal, Adolfo Delgado, Gerald Morrison

    The affinity law modified for viscosity effects is further extended to include the power input and efficiency. The power input and efficiency data generated using computational fluid dynamics (CFD) are utilized to represent dimensionless power coefficient and efficiency for the pump under consideration. The goal of modifying the affinity laws for power input is achieved by developing a new relationship where the power coefficient is modified by multiplying it by rotational Reynolds number raised to a power Π*Rew−Pat. This new relationship is then represented as a function of a modified flow coefficient ф*Rew−Mo. All the data collapse onto a single curve for varying values of the exponents Morrison number (Mo) and Patil number (Pat). Pat is further characterized as a function of flow regime and specific speed. The method also holds true for efficiency prediction, however, with different values of Mo and Pat. The proposed method is validated by using data collected from published literature.


  • Predictive Erosion Model for Mixed Flow Centrifugal Pump

    by Sahand Pirouzpanah, Abhay Patil, Yiming Chen, Gerald Morrison

    Electrical submersible pumps (ESPs) are widely used in upstream oil production. The presence of a low concentration solid phase, particle-laden flow, in the production fluid may cause severe damage in the internal sections of the pump which reduces its operating lifetime. To better understand the ESP pump's endurance, two different designs of commonly used mixed flow ESPs were studied numerically to determine the pump's flow behavior at its best efficiency point. Computational fluid dynamics (CFD) analysis was conducted on two stages of one design type of pump's primary flow path employing Eulerian–Granular scheme in ANSYS FLUENT. The key parameters affecting the erosion phenomena within the pump such as turbulence kinetic energy, local sand concentration, and near wall relative sand velocity were identified. The predictive erosion model applicable to pumps was developed by correlating the erosion key parameters with available experimental results. It is concluded that the use of an erosion model on the second design of ESP proves the model's versatility to predict the erosion on different designs of ESPs.


  • Numerical Study on the First Stage Head Degradation in an Electrical Submersible Pump With Population Balance Model

    by Yiming Chen, Abhay Patil, Yi Chen, Changrui Bai, Yintao Wang, Gerald Morrison

    Based on previous experiment result, an assumption is made to explain the abnormal head degradation in the first stage of an electrical submersible pump (ESP): the bubbles' breaking up and coalescence effect with compressibility is the main reason of this phenomenon. To investigate the head degradation problem inside the ESP, a series of numerical simulations are performed on the first stage of the split-vane impeller pump commonly employed for gas handling purpose. These three-dimensional transient Eulerian multiphase simulations are divided into two groups: one group with the traditional fixed bubble size method and the other with the ANSYS population balancing model (PBM) allowing the bubbles to break up and coalesce. The simulation result with the changing bubble size matches well with the experiment data, which supports the previous assumption. The flow field based on PBM simulation is visualized and analyzed. Also the separation of phases is discovered with large volume of gas accumulating at the suction side of the impeller trailing blades, which is also supported by experimental observation.