Borong Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Borong Hu has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
- Teng Long
Department of Engineering, University of Cambridge, Cambridge, UK
12 shared publications - Li Ran
State Key Laboratory of Power Transmission Equipment Technology, School of Electrical Engineering, Chongqing University, Chongqing, China
7 shared publications - Luke Shillaber
Electrical Engineering Division, Department of Engineering, University of Cambridge, Cambridge, U.K.
6 shared publications - Wei Mu
University of Cambridge
5 shared publications - Chaoqiang Jiang
City University of Hong Kong
4 shared publications - Liang Wang
State Key Laboratory of Power Transmission Equipment and System Security and New Technology, Chongqing University, Chongqing, China
4 shared publications
Latest Publications
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16979-16994
Stress Management of Wind Turbine Components Using a Nano-Enhanced Phase Change Material Integrated Power Module
Offshore wind turbine components endure high mechanical and thermal stress due to fluctuating wind conditions and harsh marine environments, but lack coordinated stress management due to the low thermal inertia of the power electronic system. Frequent and large pitch movements further aggravate component stress. This article introduces a power module packaging method that integrates nano-enhanced phase change materials (PCMs) to provide short-term overload capability. By mixing PCMs with carbon nanotubes, the thermal resistance per insulated gate bipolar transistor (IGBT) of the nano-enhanced PCM module is reduced by 34% and 14% compared to the conventional module and PCM module respectively due to the increased thermal conductivity of PCMs. Finite element analysis and experimental results demonstrate the superior thermal performance of the nano-enhanced PCM module over traditional modules. Based on this improved functionality, a stress management strategy is proposed to mitigate mechanical stress on the pitch system by increasing the rated wind speed and temporarily overloading the turbine powertrain system. Statistical analysis based on real wind speed profiles validates the strategy’s effectiveness, showing a reduction in the number of pitch angle cycles by up to 86% .
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16979-16994
Stress Management of Wind Turbine Components Using a Nano-Enhanced Phase Change Material Integrated Power Module
Offshore wind turbine components endure high mechanical and thermal stress due to fluctuating wind conditions and harsh marine environments, but lack coordinated stress management due to the low thermal inertia of the power electronic system. Frequent and large pitch movements further aggravate component stress. This article introduces a power module packaging method that integrates nano-enhanced phase change materials (PCMs) to provide short-term overload capability. By mixing PCMs with carbon nanotubes, the thermal resistance per insulated gate bipolar transistor (IGBT) of the nano-enhanced PCM module is reduced by 34% and 14% compared to the conventional module and PCM module respectively due to the increased thermal conductivity of PCMs. Finite element analysis and experimental results demonstrate the superior thermal performance of the nano-enhanced PCM module over traditional modules. Based on this improved functionality, a stress management strategy is proposed to mitigate mechanical stress on the pitch system by increasing the rated wind speed and temporarily overloading the turbine powertrain system. Statistical analysis based on real wind speed profiles validates the strategy’s effectiveness, showing a reduction in the number of pitch angle cycles by up to 86% .
- Open Access
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 286-299
Near Junction Integration of Vapor Chamber for Transient Thermal Performance Improvements of SiC Power Module
Power semiconductor modules are mostly stressed when faced with large junction temperature variations, leading to failures such as bond wire lift-off and solder fatigue. This issue becomes more challenging with the implementation of SiC devices because their smaller die size reduces the thermal inertia and increases the thermal resistance. This paper explores the potential of utilizing vapor chamber (VC) through near junction integration inside a SiC power module to reduce junction temperature swings. A novel fabrication process enables the near junction integration of VC which not only acts as heat spreaders but also conducts the drain current of MOSFETs. The thermal impedance analysis in the frequency domain highlights VC's strong attenuation effect on medium frequency thermal cycles, which are particularly damaging to power modules. Two case studies are performed to evaluate the thermal performance of VC integrated module in traction inverter applications. Both simulations and experiments demonstrate the effectiveness of integrating VC: more than 33% reduction in maximum junction temperature and 44% reduction in junction temperature fluctuation. Time constant spectrum analysis further reveals that the VC module's superior thermal performance stems from its ability to minimize thermal resistance components with short time constants, a benefit that is unique to near-junction thermal management
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 286-299
Open AccessNear Junction Integration of Vapor Chamber for Transient Thermal Performance Improvements of SiC Power Module
Power semiconductor modules are mostly stressed when faced with large junction temperature variations, leading to failures such as bond wire lift-off and solder fatigue. This issue becomes more challenging with the implementation of SiC devices because their smaller die size reduces the thermal inertia and increases the thermal resistance. This paper explores the potential of utilizing vapor chamber (VC) through near junction integration inside a SiC power module to reduce junction temperature swings. A novel fabrication process enables the near junction integration of VC which not only acts as heat spreaders but also conducts the drain current of MOSFETs. The thermal impedance analysis in the frequency domain highlights VC's strong attenuation effect on medium frequency thermal cycles, which are particularly damaging to power modules. Two case studies are performed to evaluate the thermal performance of VC integrated module in traction inverter applications. Both simulations and experiments demonstrate the effectiveness of integrating VC: more than 33% reduction in maximum junction temperature and 44% reduction in junction temperature fluctuation. Time constant spectrum analysis further reveals that the VC module's superior thermal performance stems from its ability to minimize thermal resistance components with short time constants, a benefit that is unique to near-junction thermal management
- 19 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (12) , 15622-15634
Forced Fluorinated Liquid Cooling for Medium Voltage SiC Power Modules: Concurrently Addressing Electrical and Thermal Challenges
Enhanced insulation and superior thermal characteristics are crucial in advanced packaging for medium voltage (MV) silicon carbide (SiC) power modules. Nonetheless, the reduction in thermal resistance typically compromises insulation level due to the decreased number of insulation layers. In this paper, the forced fluorinated liquid cooling is proposed, whereby fluorinated liquid (3M FC-40) is directed into the power module, substituting silicone gel and diminishing thermal resistance. Through the utilization of forced fluorinated liquid cooling, a reduction of 21°C in junction temperature at full load is demonstrated in the experiment, compared to traditional water cooled power modules. Furthermore, there is a 35.6% reduction observed in the maximum temperature rise Δ T j . As dissipation power is transferred from the topside of the chip to the fluorinated liquid, the possibility of unlimited stacking of direct bonded copper (DBC) is enabled to lower the electrical field, thereby facilitating insulation at the chip bottom side without any worries regarding heightened thermal resistance. Forced fluorinated liquid cooling resulted in a 39°C reduction in the double-stacked DBC power module. Moreover, partial discharge (PD) detection under square wave revealed that the DBC immersed in the fluorinated liquid remains free from PD at 10 kV, a significantly higher threshold than observed with silicone gel. A higher partial discharge inception voltage (PDIV) is anticipated for double-stacked DBC when immersed in 3M FC-40. Thus, the forced fluorinated liquid cooling can be considered a promising solution for the next generation of MV SiC power modules.
- 19 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (12) , 15622-15634
Forced Fluorinated Liquid Cooling for Medium Voltage SiC Power Modules: Concurrently Addressing Electrical and Thermal Challenges
Enhanced insulation and superior thermal characteristics are crucial in advanced packaging for medium voltage (MV) silicon carbide (SiC) power modules. Nonetheless, the reduction in thermal resistance typically compromises insulation level due to the decreased number of insulation layers. In this paper, the forced fluorinated liquid cooling is proposed, whereby fluorinated liquid (3M FC-40) is directed into the power module, substituting silicone gel and diminishing thermal resistance. Through the utilization of forced fluorinated liquid cooling, a reduction of 21°C in junction temperature at full load is demonstrated in the experiment, compared to traditional water cooled power modules. Furthermore, there is a 35.6% reduction observed in the maximum temperature rise Δ T j . As dissipation power is transferred from the topside of the chip to the fluorinated liquid, the possibility of unlimited stacking of direct bonded copper (DBC) is enabled to lower the electrical field, thereby facilitating insulation at the chip bottom side without any worries regarding heightened thermal resistance. Forced fluorinated liquid cooling resulted in a 39°C reduction in the double-stacked DBC power module. Moreover, partial discharge (PD) detection under square wave revealed that the DBC immersed in the fluorinated liquid remains free from PD at 10 kV, a significantly higher threshold than observed with silicone gel. A higher partial discharge inception voltage (PDIV) is anticipated for double-stacked DBC when immersed in 3M FC-40. Thus, the forced fluorinated liquid cooling can be considered a promising solution for the next generation of MV SiC power modules.
- 30 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (1) , 798-808
Gapless Transformer Design by Using Nanocrystalline Flake Ribbon
Air gaps are essential to avoid core saturation in power magnetic components. However, discrete air gaps cause more severe fringing effect which increase winding and core losses. Gapless design is difficult in high-power applications due to the limitation of materials with suitable electromagnetic properties. In this article, an emerging nanocrystalline flake ribbon (NFR) has been used to form gapless magnetic cores for high frequency transformers. Loss reduction of the entire transformer has been achieved without the discrete air gaps. The power density of the transformer is competitive due to suitable permeability and saturation point of NFR at high frequencies (hundreds kHz). The core losses are separated and compared with its precursor conventional nanocrystalline ribbon. Comparison to two other transformers using ferrite and nanocrystalline materials has been carried out in a 5.5 kW, 100 kHz dual active bridge (DAB) converter. The transformer using the NFR core shows the highest efficiency. The NFR transformer exhibits 33.2 % and 67.1 % winding loss reduction compared to the ferrite and the nanocrystalline transformer, respectively. Error analysis has shown the loss measurement error is within 6.1%.
- 30 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (1) , 798-808
Gapless Transformer Design by Using Nanocrystalline Flake Ribbon
Air gaps are essential to avoid core saturation in power magnetic components. However, discrete air gaps cause more severe fringing effect which increase winding and core losses. Gapless design is difficult in high-power applications due to the limitation of materials with suitable electromagnetic properties. In this article, an emerging nanocrystalline flake ribbon (NFR) has been used to form gapless magnetic cores for high frequency transformers. Loss reduction of the entire transformer has been achieved without the discrete air gaps. The power density of the transformer is competitive due to suitable permeability and saturation point of NFR at high frequencies (hundreds kHz). The core losses are separated and compared with its precursor conventional nanocrystalline ribbon. Comparison to two other transformers using ferrite and nanocrystalline materials has been carried out in a 5.5 kW, 100 kHz dual active bridge (DAB) converter. The transformer using the NFR core shows the highest efficiency. The NFR transformer exhibits 33.2 % and 67.1 % winding loss reduction compared to the ferrite and the nanocrystalline transformer, respectively. Error analysis has shown the loss measurement error is within 6.1%.
- Open Access
- 2 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Condition Monitoring of Wind Turbine Converters with Limited and Unbalanced SCADA Data
This paper proposes a condition monitoring (CM) framework to detect the health-to-fault operational behavior of wind turbine (WT) converters based on SCADA data from early-stage operation. A novel method for characterizing operating data distribution is proposed to exploit the limited and unbalanced SCADA data. By providing weighting factors for cost functions, this method significantly improves the robustness and generalization of the CM method. The CM framework is also enabled for the full life cycle including early-stage and long-term operation, by employing an online learning algorithm. Validation with both healthy and faulty WTs demonstrates the potential to detect abnormality a few days before actual converter faults occur.
- 2 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessCondition Monitoring of Wind Turbine Converters with Limited and Unbalanced SCADA Data
This paper proposes a condition monitoring (CM) framework to detect the health-to-fault operational behavior of wind turbine (WT) converters based on SCADA data from early-stage operation. A novel method for characterizing operating data distribution is proposed to exploit the limited and unbalanced SCADA data. By providing weighting factors for cost functions, this method significantly improves the robustness and generalization of the CM method. The CM framework is also enabled for the full life cycle including early-stage and long-term operation, by employing an online learning algorithm. Validation with both healthy and faulty WTs demonstrates the potential to detect abnormality a few days before actual converter faults occur.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 13744-13757
In-Situ Monitoring Solder Layer Degradation in Multichip IGBT Power Modules Using Auxiliary Emitter Voltage
Asymmetric chip placement and initial die-attach defects within a multichip IGBT power module (MIPM) can cause uneven junction temperature distribution and further accelerate the solder layer degradation. This is one of the main factors which affect the performance and reliability. This study uses the auxiliary emitter voltage v eE to indirectly measure the turn- on delay time and the maximum rate of change of the collector current. The physical significance of the virtual junction temperature extracted from the two measurands is clarified. The correspondence between the v eE and the degradation level of the solder layer is established using the difference between the two estimated temperatures. A novel condition monitoring method is then proposed in this article to identify the degradation level of individual solder layers using v eE , which separates the effects of solder layer fatigue and bonding wires lift-off. The current dependence of the proposed method is negligible. Simulation and experimental results indicate that the proposed method can sensitively detect the highest degradation level of the chip in a MIPM in real-time.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 13744-13757
In-Situ Monitoring Solder Layer Degradation in Multichip IGBT Power Modules Using Auxiliary Emitter Voltage
Asymmetric chip placement and initial die-attach defects within a multichip IGBT power module (MIPM) can cause uneven junction temperature distribution and further accelerate the solder layer degradation. This is one of the main factors which affect the performance and reliability. This study uses the auxiliary emitter voltage v eE to indirectly measure the turn- on delay time and the maximum rate of change of the collector current. The physical significance of the virtual junction temperature extracted from the two measurands is clarified. The correspondence between the v eE and the degradation level of the solder layer is established using the difference between the two estimated temperatures. A novel condition monitoring method is then proposed in this article to identify the degradation level of individual solder layers using v eE , which separates the effects of solder layer fatigue and bonding wires lift-off. The current dependence of the proposed method is negligible. Simulation and experimental results indicate that the proposed method can sensitively detect the highest degradation level of the chip in a MIPM in real-time.
- 3 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12 (4) , 3588-3606
A Review of Partial Discharge in Medium Voltage SiC Power Modules Under Square Wave Excitation: Characterization, Mitigation, and Detection
The medium voltage (MV) silicon carbide (SiC) power modules hold significant promise as a route for the solid-state converters to achieve higher power density, higher switching frequency, and lower loss. However, the emergence of partial discharge (PD) in the MV SiC power modules has posed a formidable challenge to enhancing its nominal voltage. In this paper, a comprehensive review and comparative analysis of characterization, mitigation, and detection of PD under the square wave excitation is proposed for MV SiC power modules. First, the mechanism, detriments, and characterization of the PD issue and electrical tree in the MV power module are insightfully demonstrated. Meanwhile, the challenges from the PD for the MV SiC power module are emphasized. Besides, the geometric modification of direct bonded copper (DBC) structures to mitigate the PD issue are reviewed in detail. The limitations of the customized DBC are analyzed, considering the cost, reliability, and thermal resistance. Additionally, advanced dielectric materials are introduced and categorized. It is indicated that the effectiveness of the new dielectric under the square wave excitation stress still needs further investigation. Meanwhile, the optical, electromagnetic, electrical, and ultrasound detection methods under square wave excitation are further reviewed to assess the PD behavior in the MV SiC power module. Lastly, suggested future researches for MV SiC power module packaging are proposed, aiming to inspire new ideas to further promote the insulation level of the MV SiC power module.
- 3 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12 (4) , 3588-3606
A Review of Partial Discharge in Medium Voltage SiC Power Modules Under Square Wave Excitation: Characterization, Mitigation, and Detection
The medium voltage (MV) silicon carbide (SiC) power modules hold significant promise as a route for the solid-state converters to achieve higher power density, higher switching frequency, and lower loss. However, the emergence of partial discharge (PD) in the MV SiC power modules has posed a formidable challenge to enhancing its nominal voltage. In this paper, a comprehensive review and comparative analysis of characterization, mitigation, and detection of PD under the square wave excitation is proposed for MV SiC power modules. First, the mechanism, detriments, and characterization of the PD issue and electrical tree in the MV power module are insightfully demonstrated. Meanwhile, the challenges from the PD for the MV SiC power module are emphasized. Besides, the geometric modification of direct bonded copper (DBC) structures to mitigate the PD issue are reviewed in detail. The limitations of the customized DBC are analyzed, considering the cost, reliability, and thermal resistance. Additionally, advanced dielectric materials are introduced and categorized. It is indicated that the effectiveness of the new dielectric under the square wave excitation stress still needs further investigation. Meanwhile, the optical, electromagnetic, electrical, and ultrasound detection methods under square wave excitation are further reviewed to assess the PD behavior in the MV SiC power module. Lastly, suggested future researches for MV SiC power module packaging are proposed, aiming to inspire new ideas to further promote the insulation level of the MV SiC power module.
- Open Access
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9614-9628
Substrate Embedded Power Electronics Packaging for Silicon Carbide mosfets
This article proposes a new power electronic packaging for discrete dies, namely, a standard cell, which consists of a step-etched active metal brazing (AMB) substrate and a flexible printed circuit board (flex-PCB). The standard cell exhibits high thermal conductivity, complete electrical insulation, and low stray inductance, thereby enhancing the performance of SiC mosfet devices. The standard cell has a stray power loop inductance of less than $\text{1}\,\text{nH}$ and a gate loop inductance of less than $\text{1.5}\,\text{nH}$ . The standard cell has a flat body with surface-mounting electrical connections on one side and direct thermal connections on the other. The use of flex-PCB die interconnection enables maximum utilization of source pads while providing a flexible gate-source connection and the converter PCB. This article presents the design concept of the standard cell and experimentally validates its effectiveness in a converter system.
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9614-9628
Open AccessSubstrate Embedded Power Electronics Packaging for Silicon Carbide mosfets
This article proposes a new power electronic packaging for discrete dies, namely, a standard cell, which consists of a step-etched active metal brazing (AMB) substrate and a flexible printed circuit board (flex-PCB). The standard cell exhibits high thermal conductivity, complete electrical insulation, and low stray inductance, thereby enhancing the performance of SiC mosfet devices. The standard cell has a stray power loop inductance of less than $\text{1}\,\text{nH}$ and a gate loop inductance of less than $\text{1.5}\,\text{nH}$ . The standard cell has a flat body with surface-mounting electrical connections on one side and direct thermal connections on the other. The use of flex-PCB die interconnection enables maximum utilization of source pads while providing a flexible gate-source connection and the converter PCB. This article presents the design concept of the standard cell and experimentally validates its effectiveness in a converter system.
- Open Access
- 1 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 737-753
Adjustable High Current Low Profile Sandwich Inductor Using Nanocrystalline Flake Ribbon Core
Compact and high current inductors determine the power density and efficiency of voltage regulators (VRs) for computing ICs. Conventional moulding structures using powder cores and gapped ferrite cores are reaching the limits of size miniaturisation. In this paper, a sandwich-structured inductor using 2D magnetic nanocrystalline flake ribbon (NFR) is developed to achieve high current density and low height. The analytical models of inductance and conduction losses are developed and validated by finite element methods and experiments. A 5 to 1 V, 50A, VR is built to compare the performance of the fabricated NFR sandwich inductor to the latest commercial counterpart. Thermal performance is investigated, stability tests under solder iron heat and reflow temperature are performed. The fabricated sandwich inductor is featured as simple structure, low profile, low DC resistance (DCR), high saturation current, soldering heat stable, but in the modest compromise of the AC conduction and core losses.
- 1 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 737-753
Open AccessAdjustable High Current Low Profile Sandwich Inductor Using Nanocrystalline Flake Ribbon Core
Compact and high current inductors determine the power density and efficiency of voltage regulators (VRs) for computing ICs. Conventional moulding structures using powder cores and gapped ferrite cores are reaching the limits of size miniaturisation. In this paper, a sandwich-structured inductor using 2D magnetic nanocrystalline flake ribbon (NFR) is developed to achieve high current density and low height. The analytical models of inductance and conduction losses are developed and validated by finite element methods and experiments. A 5 to 1 V, 50A, VR is built to compare the performance of the fabricated NFR sandwich inductor to the latest commercial counterpart. Thermal performance is investigated, stability tests under solder iron heat and reflow temperature are performed. The fabricated sandwich inductor is featured as simple structure, low profile, low DC resistance (DCR), high saturation current, soldering heat stable, but in the modest compromise of the AC conduction and core losses.
- Open Access
- 27 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (7) , 7808-7814
Liquid Metal Fluidic Connection and Floating Die Structure for Ultralow Thermomechanical Stress of SiC Power Electronics Packaging
Coefficients of thermal expansion (CTE) of various materials in packaging structure layers vary largely, causing significant thermomechanical stress in power electronic packages during operation. For wirebondless SiC modules, the stress is even larger due to the structure's rigidity and the high Young's modulus of SiC crystals. This letter takes a flexible printed circuit board (FPCB)/die/active metal brazed (AMB) packaging stack as an example to prove the feasibility of floating die structure enabled by liquid metal (LM) fluidic connection. The CTE mismatch among the die, printed circuit board, and AMB substrate is decoupled by the LM layer without compromise of thermal and electrical conduction. The finite-element analysis demonstrates a 56% reduction in von Mises stress of the device and more than 99% shear stress reduction at the FPCB-AMB interface, compared with a conventional rigid solder connection. Testing results show that LM-based packaging has a similar thermal and electrical conduction and higher breakdown voltage when compared with the soldered counterpart. Accelerated thermal cycling aging tests validate the stability of the insulation ring for LM-based packaging, especially under high-temperature conditions. The feasibility of using LM fluidic interconnections for a floating die structure of SiC packaging is validated.
- 27 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (7) , 7808-7814
Open AccessLiquid Metal Fluidic Connection and Floating Die Structure for Ultralow Thermomechanical Stress of SiC Power Electronics Packaging
Coefficients of thermal expansion (CTE) of various materials in packaging structure layers vary largely, causing significant thermomechanical stress in power electronic packages during operation. For wirebondless SiC modules, the stress is even larger due to the structure's rigidity and the high Young's modulus of SiC crystals. This letter takes a flexible printed circuit board (FPCB)/die/active metal brazed (AMB) packaging stack as an example to prove the feasibility of floating die structure enabled by liquid metal (LM) fluidic connection. The CTE mismatch among the die, printed circuit board, and AMB substrate is decoupled by the LM layer without compromise of thermal and electrical conduction. The finite-element analysis demonstrates a 56% reduction in von Mises stress of the device and more than 99% shear stress reduction at the FPCB-AMB interface, compared with a conventional rigid solder connection. Testing results show that LM-based packaging has a similar thermal and electrical conduction and higher breakdown voltage when compared with the soldered counterpart. Accelerated thermal cycling aging tests validate the stability of the insulation ring for LM-based packaging, especially under high-temperature conditions. The feasibility of using LM fluidic interconnections for a floating die structure of SiC packaging is validated.