Salvatore Levantino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Salvatore Levantino has a total of 103 co-authors. Here are the top co-authors by number of shared publications:
- Carlo Samori
Department of Electronics, Information and Bioengineering (DEIB), Politecnico di Milano, Milan, Italy
101 shared publications - Andrea Leonardo Lacaita
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
87 shared publications - Andrea Bonfanti
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milano, Italy
23 shared publications - Luca Bertulessi
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milano, Italy
19 shared publications - Francesco Tesolin
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy
15 shared publications Dmytro Cherniak
Infineon Technologies AG, Villach, Austria
14 shared publications
Latest Publications
- Open Access
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1844-1859
A Wideband Digitally Assisted Frequency Tripler With Adaptively Optimized Output Power in 55-nm SiGe BiCMOS
This article presents a 28–38-GHz frequency tripler implemented in 55-nm SiGe BiCMOS technology with a novel on-chip background calibration technique. This technique continuously optimizes the circuit performance by maximizing output power and improving fundamental harmonic rejection. The proposed tripler achieves wideband operation and robust performance across varying operating conditions and input-power levels. The calibrated tripler demonstrates more than 40 dB of fundamental harmonic rejection and a 10.2-GHz (30.3%) 3-dB bandwidth. It occupies an area of 0.16 mm2 and consumes 54 mW of power. The results show the tripler maintains its performance over a 13-dB input-power variation, confirming the effectiveness of the proposed calibration method.
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1844-1859
Open AccessA Wideband Digitally Assisted Frequency Tripler With Adaptively Optimized Output Power in 55-nm SiGe BiCMOS
This article presents a 28–38-GHz frequency tripler implemented in 55-nm SiGe BiCMOS technology with a novel on-chip background calibration technique. This technique continuously optimizes the circuit performance by maximizing output power and improving fundamental harmonic rejection. The proposed tripler achieves wideband operation and robust performance across varying operating conditions and input-power levels. The calibrated tripler demonstrates more than 40 dB of fundamental harmonic rejection and a 10.2-GHz (30.3%) 3-dB bandwidth. It occupies an area of 0.16 mm2 and consumes 54 mW of power. The results show the tripler maintains its performance over a 13-dB input-power variation, confirming the effectiveness of the proposed calibration method.
- Open Access
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-17
A Low Jitter and Low Spur Fractional-N Digital PLL Based on a DTC Chopping Technique
This work presents a digital-to-time converter (DTC)-based fractional-N digital phase-locked loop (PLL) designed to achieve simultaneously low jitter and low spurs. We introduce a novel DTC chopping technique that effectively mitigates fractional spurs, which we identify as predominantly arising from even-order nonlinearity invariable-slope (VS) DTCs. The proposed technique suppresses such spurs by randomly alternating the DTC position between the reference and divider signal paths. In addition, it proves effective in reducing the DTC flicker noise contribution. To ensure robust operation across process, voltage, and temperature (PVT) spreads, the design incorporates several background adaptive digital algorithms. Fabricated in a 28-nm CMOS process, the synthesizer occupies an active area of 0.22 mm2 and consumes 16.7 mW. At a 9.275-GHz near-integer channel, the measured worst case in-band fractional spur remains below −63 dBc, and the integrated rms jitter under 80 fs, yielding a jitter-power figure of merit (FoM) of −249.8 dB.
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-17
Open AccessA Low Jitter and Low Spur Fractional-N Digital PLL Based on a DTC Chopping Technique
This work presents a digital-to-time converter (DTC)-based fractional-N digital phase-locked loop (PLL) designed to achieve simultaneously low jitter and low spurs. We introduce a novel DTC chopping technique that effectively mitigates fractional spurs, which we identify as predominantly arising from even-order nonlinearity invariable-slope (VS) DTCs. The proposed technique suppresses such spurs by randomly alternating the DTC position between the reference and divider signal paths. In addition, it proves effective in reducing the DTC flicker noise contribution. To ensure robust operation across process, voltage, and temperature (PVT) spreads, the design incorporates several background adaptive digital algorithms. Fabricated in a 28-nm CMOS process, the synthesizer occupies an active area of 0.22 mm2 and consumes 16.7 mW. At a 9.275-GHz near-integer channel, the measured worst case in-band fractional spur remains below −63 dBc, and the integrated rms jitter under 80 fs, yielding a jitter-power figure of merit (FoM) of −249.8 dB.
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
A 20-MHz BW 12.3-ENOB Third-Order Noise-Shaping SAR ADC With Multi-Input Architecture and PVT-Robust Ratio-Based FIA
Noise-shaping successive approximation register (NS-SAR) ADCs combine high resolution with energy efficiency, but their performance degrades at bandwidths in the tens of MHz due to limited oversampling ratios (OSR) and adoption of low-order passive filters. This work introduces a $3{^{\text {rd}}}$ -order NS-SAR ADC that leverages a multi-input amplifier and a multi-input comparator, enabling independent optimization and flexible filter coefficient sizing. In addition, a ratio-based floating inverter amplifier ensures remarkable gain stability across process, voltage, and temperature (PVT) variations. Implemented in a 28-nm CMOS process, the prototype achieves 12.3-ENOB over a 20-MHz bandwidth while consuming 1.56 mW, resulting in a Schreier figure-of-merit (FoMS) of 177-dB with robust and consistent performance across PVT corners.
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
A 20-MHz BW 12.3-ENOB Third-Order Noise-Shaping SAR ADC With Multi-Input Architecture and PVT-Robust Ratio-Based FIA
Noise-shaping successive approximation register (NS-SAR) ADCs combine high resolution with energy efficiency, but their performance degrades at bandwidths in the tens of MHz due to limited oversampling ratios (OSR) and adoption of low-order passive filters. This work introduces a $3{^{\text {rd}}}$ -order NS-SAR ADC that leverages a multi-input amplifier and a multi-input comparator, enabling independent optimization and flexible filter coefficient sizing. In addition, a ratio-based floating inverter amplifier ensures remarkable gain stability across process, voltage, and temperature (PVT) variations. Implemented in a 28-nm CMOS process, the prototype achieves 12.3-ENOB over a 20-MHz bandwidth while consuming 1.56 mW, resulting in a Schreier figure-of-merit (FoMS) of 177-dB with robust and consistent performance across PVT corners.
- 13 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (1) , 93-97
Frequency Synchronization Techniques for DC–DC Converters With Time-Based Control
In this brief, a frequency synchronization method for time-based-controlled power converters is presented. The proposed synchronization technique makes it possible to precisely lock the internal oscillators frequency of the time-based controller (i.e., the power converter switching frequency) to any externally provided clock signal, without trading the dynamic performance. By leveraging the differential structure of the time-based controller, the proposed feedback loop operates orthogonally with respect to the main voltage regulation loop, minimizing any interaction with the latter. The presented frequency synchronization scheme has been implemented on a time-based buck converter in a 180-nm BCD process to fully verify the performance.
- 13 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (1) , 93-97
Frequency Synchronization Techniques for DC–DC Converters With Time-Based Control
In this brief, a frequency synchronization method for time-based-controlled power converters is presented. The proposed synchronization technique makes it possible to precisely lock the internal oscillators frequency of the time-based controller (i.e., the power converter switching frequency) to any externally provided clock signal, without trading the dynamic performance. By leveraging the differential structure of the time-based controller, the proposed feedback loop operates orthogonally with respect to the main voltage regulation loop, minimizing any interaction with the latter. The presented frequency synchronization scheme has been implemented on a time-based buck converter in a 180-nm BCD process to fully verify the performance.
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (12) , 4572-4586
A Low-Noise Digital PLL With an Adaptive Common-Mode Resonance Tuning Technique for Voltage-Biased Oscillators
This work presents a digital phase-locked loop (PLL) incorporating an adaptive common-mode (CM) resonance tuning technique applied to a voltage-biased digitally-controlled oscillator (DCO). The method leverages the principle that the sensitivity of the oscillator frequency to a dither signal injected into the gate voltage of the cross-coupled transistors diminishes to near zero when the CM resonance is optimally tuned for minimal phase noise (PN). By detecting and nullifying this sensitivity, the proposed technique automatically adjusts the CM resonance to its ideal value. This background operation is continuous across the entire tuning range. The concept was validated through a digital PLL prototype fabricated in a 28-nm CMOS process, which achieved a jitter of 45.9 fs, a power-versus-jitter figure-of-merit of −257 dB, and a PN of −146.6 dBc/Hz at 10-MHz offset from a 4.75-GHz carrier, all within an active area of 0.21 mm2 .
- 30 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (12) , 4572-4586
A Low-Noise Digital PLL With an Adaptive Common-Mode Resonance Tuning Technique for Voltage-Biased Oscillators
This work presents a digital phase-locked loop (PLL) incorporating an adaptive common-mode (CM) resonance tuning technique applied to a voltage-biased digitally-controlled oscillator (DCO). The method leverages the principle that the sensitivity of the oscillator frequency to a dither signal injected into the gate voltage of the cross-coupled transistors diminishes to near zero when the CM resonance is optimally tuned for minimal phase noise (PN). By detecting and nullifying this sensitivity, the proposed technique automatically adjusts the CM resonance to its ideal value. This background operation is continuous across the entire tuning range. The concept was validated through a digital PLL prototype fabricated in a 28-nm CMOS process, which achieved a jitter of 45.9 fs, a power-versus-jitter figure-of-merit of −257 dB, and a PN of −146.6 dBc/Hz at 10-MHz offset from a 4.75-GHz carrier, all within an active area of 0.21 mm2 .
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (1) , 331-342
A Low-Jitter Fractional- N Digital PLL With Spur Cancellation Based on a Multi-DTC Topology
This work presents a low-jitter and low-spur fractional-N digital phase-locked loop (PLL) with a multi-path topology, each path having its own digital-to-time converter (DTC) and phase detector (PD). We show that, by driving each DTC with properly shifted quantization error sequences and then combining the PD outputs, the dominant fractional spurs due to DTC non-linearity can be canceled out and a significant reduction in DTC jitter is obtained. A number of background adaptive digital algorithms are introduced to ensure a robust operation across PVT spreads. The implemented PLL prototype, fabricated in a 28 nm CMOS process, has an active area of 0.36 mm2 and dissipates 17.9 mW. At 9.25 GHz near-integer channels, the measured worst case fractional spur is below $-\textrm {60}$ dBc, with an rms jitter of 77.1 fs, leading to $-\textrm {249.7}$ dB jitter-power figure-of-merit.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (1) , 331-342
A Low-Jitter Fractional- N Digital PLL With Spur Cancellation Based on a Multi-DTC Topology
This work presents a low-jitter and low-spur fractional-N digital phase-locked loop (PLL) with a multi-path topology, each path having its own digital-to-time converter (DTC) and phase detector (PD). We show that, by driving each DTC with properly shifted quantization error sequences and then combining the PD outputs, the dominant fractional spurs due to DTC non-linearity can be canceled out and a significant reduction in DTC jitter is obtained. A number of background adaptive digital algorithms are introduced to ensure a robust operation across PVT spreads. The implemented PLL prototype, fabricated in a 28 nm CMOS process, has an active area of 0.36 mm2 and dissipates 17.9 mW. At 9.25 GHz near-integer channels, the measured worst case fractional spur is below $-\textrm {60}$ dBc, with an rms jitter of 77.1 fs, leading to $-\textrm {249.7}$ dB jitter-power figure-of-merit.
- Open Access
- 29 March 2025
- Published by Springer Nature
- p. 55-65
Localized LO Phase Shifting for Phased Array Systems
Multiple-input-multiple-output is a promising technology to enable spatial multiplexing and improve throughput in wireless communication systems. The phase shifter needed in each element of the phased array to perform the electronic steering of the beam typically introduces a non-ideal transfer function in the signal path and consumes significant area and power, making it a major source of cost and dissipation. To address those issues, this chapter describes a novel technique referred to as localized LO phase-shifting, where the array of phase shifters in the receiver and in the transmitter is replaced by an array of synchronized PLLs, providing the local oscillation to each path, with fine and inherently linear phase regulation. This approach not only helps reduce power consumption and area occupation, in modern CMOS nodes, but also improves phase noise since the beam is formed by the combination of uncorrelated noise sources. To demonstrate the concept, a dual-element LO phase-shifting system, based on fractional-N digital PLLs in the 8.5-to-10.0-GHz range, is implemented in a standard 28-nm CMOS process. Each element occupies 0.23 mm2 of area and dissipates 20 mW of power. An arbitrary phase shift between the LO outputs can be set over the full 360 $$^{\circ }$$ range with a resolution of 0.7 millidegrees. The measured rms phase accuracy is 0.76 $$^{\circ }$$ , and the peak-to-peak phase error is 2.1 $$^{\circ }$$ , without requiring any linearity or gain calibration. Combining the outputs of the two elements, the measured integrated random jitter scales down from 58.5 to 44.6 fs rms.- 29 March 2025
- Published by Springer Nature
- p. 55-65
Open AccessLocalized LO Phase Shifting for Phased Array Systems
Multiple-input-multiple-output is a promising technology to enable spatial multiplexing and improve throughput in wireless communication systems. The phase shifter needed in each element of the phased array to perform the electronic steering of the beam typically introduces a non-ideal transfer function in the signal path and consumes significant area and power, making it a major source of cost and dissipation. To address those issues, this chapter describes a novel technique referred to as localized LO phase-shifting, where the array of phase shifters in the receiver and in the transmitter is replaced by an array of synchronized PLLs, providing the local oscillation to each path, with fine and inherently linear phase regulation. This approach not only helps reduce power consumption and area occupation, in modern CMOS nodes, but also improves phase noise since the beam is formed by the combination of uncorrelated noise sources. To demonstrate the concept, a dual-element LO phase-shifting system, based on fractional-N digital PLLs in the 8.5-to-10.0-GHz range, is implemented in a standard 28-nm CMOS process. Each element occupies 0.23 mm2 of area and dissipates 20 mW of power. An arbitrary phase shift between the LO outputs can be set over the full 360 $$^{\circ }$$ range with a resolution of 0.7 millidegrees. The measured rms phase accuracy is 0.76 $$^{\circ }$$ , and the peak-to-peak phase error is 2.1 $$^{\circ }$$ , without requiring any linearity or gain calibration. Combining the outputs of the two elements, the measured integrated random jitter scales down from 58.5 to 44.6 fs rms.