Daniel Mombeini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Daniel Mombeini has a total of 1 co-authors. Here are the top co-authors by number of shared publications:
- Amir Atrian
Islamic Azad University
2 shared publications
Latest Publications
- 25 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 0965d5
Experimental investigation into the effects of deep cold rolling on the surface quality and hardness of brass C38500
In the current study, the effect of deep cold rolling (DCR) as a mechanical surface treatment on the surface quality of C38500 brass alloy is investigated. To this end, the surface roughness and hardness of the raw material is measured firstly using the roughness and hardness tester. A simple tool is designed and fabricated for performing the treatments using surface pressure induced by a small ball. DCR process is accomplished by different kinds of balls to determine the effects of ball hardness on the surface roughness and hardness. Then, roughness and hardness tests are carried out for the treated specimens. Results show about 930% and 8.4% improvement for surface roughness and hardness regarding to best conditions, respectively. Also, subsurface hardness shows this treatment can shift the hardness curves to higher values. It is also obtained that different materials for ball and its surface quality as well as different rolling depths caused various results. The minimum surface scratches (roughness) of ball leads to high quality treated specimen. Higher ball hardness causes more deformation on the surface of specimen similar to higher rolling depth.
- 25 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 0965d5
Experimental investigation into the effects of deep cold rolling on the surface quality and hardness of brass C38500
In the current study, the effect of deep cold rolling (DCR) as a mechanical surface treatment on the surface quality of C38500 brass alloy is investigated. To this end, the surface roughness and hardness of the raw material is measured firstly using the roughness and hardness tester. A simple tool is designed and fabricated for performing the treatments using surface pressure induced by a small ball. DCR process is accomplished by different kinds of balls to determine the effects of ball hardness on the surface roughness and hardness. Then, roughness and hardness tests are carried out for the treated specimens. Results show about 930% and 8.4% improvement for surface roughness and hardness regarding to best conditions, respectively. Also, subsurface hardness shows this treatment can shift the hardness curves to higher values. It is also obtained that different materials for ball and its surface quality as well as different rolling depths caused various results. The minimum surface scratches (roughness) of ball leads to high quality treated specimen. Higher ball hardness causes more deformation on the surface of specimen similar to higher rolling depth.
- Open Access
- 4 June 2018
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 15 (4)
Investigation of Deep Cold Rolling Effects on the Bending Fatigue of Brass C38500
In this paper, the effects of deep cold rolling (DCR) process on the bending fatigue behavior of brass C38500 are investigated. Unilateral rotary bending fatigue tests were conducted by an automatic device on the basis of Moore rotary bending instrument. The treatment was done for various rolling depths (rolling forces) and one repeated pass to find the most effective conditions. It was found that rolling depth of 75 µm had the best results and could improve the fatigue life about 20% and 302% for high and low cycle fatigue regimes, respectively. At the end, the results were discussed more using both microscopic examinations and finite element (FE) simulations in ABAQUS.
- 4 June 2018
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 15 (4)
Open AccessInvestigation of Deep Cold Rolling Effects on the Bending Fatigue of Brass C38500
In this paper, the effects of deep cold rolling (DCR) process on the bending fatigue behavior of brass C38500 are investigated. Unilateral rotary bending fatigue tests were conducted by an automatic device on the basis of Moore rotary bending instrument. The treatment was done for various rolling depths (rolling forces) and one repeated pass to find the most effective conditions. It was found that rolling depth of 75 µm had the best results and could improve the fatigue life about 20% and 302% for high and low cycle fatigue regimes, respectively. At the end, the results were discussed more using both microscopic examinations and finite element (FE) simulations in ABAQUS.