Amir Atrian
Research Subjects
Amir Atrian has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Aazam Ghassemi
Islamic Azad Univ, Dept Mech Engn, Najafabad Branch, Najafabad, Iran
2 shared publications - Daniel Mombeini
Mechanical engineering, Islamic Azad University Najafabad Branch, Najafabad, 8514143131
2 shared publications - Gholam Hossein Majzoobi
Mechanical Engineering Department, Engineering Faculty, Bu-Ali Sina University, Hamedan, Iran
2 shared publications S. H. Nourbakhsh
Shahrekord University
2 shared publications- Sajjad Sattari
Young Researchers and Elite Club, Najafabad Branch, Islamic Azad University, Najafabad, Iran
2 shared publications - Sayed Hassan Nourbakhsh
Department of Mechanical Engineering, Shahrekord University, Shahrekord, Iran
2 shared publications
Latest Publications
- Open Access
- 14 December 2021
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 21 (1) , e202100134
A Partitioned Scheme for Coupling of FEM and DEM Simulations of Granular Materials
In this contribution, a simple uniaxial compaction of granular materials is considered in preparation for studying the collision behavior of double‐hull vessels filled with granular materials. The top compressing plate is deformable and modeled by the finite element method (FEM). The particles modeled using the discrete element method (DEM) are compressed by the top plate. To this end, a partitioned technique to couple the continuum approach (FEM) and particle discretization (DEM) is presented. Full agreement of the computed reaction force in DEM with the pressure applied on the top plate in FEM implies accuracy of the used coupling technique.
- 14 December 2021
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 21 (1) , e202100134
Open AccessA Partitioned Scheme for Coupling of FEM and DEM Simulations of Granular Materials
In this contribution, a simple uniaxial compaction of granular materials is considered in preparation for studying the collision behavior of double‐hull vessels filled with granular materials. The top compressing plate is deformable and modeled by the finite element method (FEM). The particles modeled using the discrete element method (DEM) are compressed by the top plate. To this end, a partitioned technique to couple the continuum approach (FEM) and particle discretization (DEM) is presented. Full agreement of the computed reaction force in DEM with the pressure applied on the top plate in FEM implies accuracy of the used coupling technique.
- Open Access
- 1 December 2020
- Vol. 5 (2) , 1-10
Experimental Investigation of the Effect of Circular Outout Trigger on Energy Absorption of Three-layered Steel/Polypropylene/Aluminum Deep Drawn Cups
- 1 December 2020
- Vol. 5 (2) , 1-10
Open AccessExperimental Investigation of the Effect of Circular Outout Trigger on Energy Absorption of Three-layered Steel/Polypropylene/Aluminum Deep Drawn Cups
- 25 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 0965d5
Experimental investigation into the effects of deep cold rolling on the surface quality and hardness of brass C38500
In the current study, the effect of deep cold rolling (DCR) as a mechanical surface treatment on the surface quality of C38500 brass alloy is investigated. To this end, the surface roughness and hardness of the raw material is measured firstly using the roughness and hardness tester. A simple tool is designed and fabricated for performing the treatments using surface pressure induced by a small ball. DCR process is accomplished by different kinds of balls to determine the effects of ball hardness on the surface roughness and hardness. Then, roughness and hardness tests are carried out for the treated specimens. Results show about 930% and 8.4% improvement for surface roughness and hardness regarding to best conditions, respectively. Also, subsurface hardness shows this treatment can shift the hardness curves to higher values. It is also obtained that different materials for ball and its surface quality as well as different rolling depths caused various results. The minimum surface scratches (roughness) of ball leads to high quality treated specimen. Higher ball hardness causes more deformation on the surface of specimen similar to higher rolling depth.
- 25 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 0965d5
Experimental investigation into the effects of deep cold rolling on the surface quality and hardness of brass C38500
In the current study, the effect of deep cold rolling (DCR) as a mechanical surface treatment on the surface quality of C38500 brass alloy is investigated. To this end, the surface roughness and hardness of the raw material is measured firstly using the roughness and hardness tester. A simple tool is designed and fabricated for performing the treatments using surface pressure induced by a small ball. DCR process is accomplished by different kinds of balls to determine the effects of ball hardness on the surface roughness and hardness. Then, roughness and hardness tests are carried out for the treated specimens. Results show about 930% and 8.4% improvement for surface roughness and hardness regarding to best conditions, respectively. Also, subsurface hardness shows this treatment can shift the hardness curves to higher values. It is also obtained that different materials for ball and its surface quality as well as different rolling depths caused various results. The minimum surface scratches (roughness) of ball leads to high quality treated specimen. Higher ball hardness causes more deformation on the surface of specimen similar to higher rolling depth.
- 24 June 2019
- Published by Springer Nature in Applied Mathematics and Mechanics
- Vol. 40 (9) , 1335-1360
Compensation of stress intensity factors in hollow cylinders containing several cracks under torsion by electro-elastic coating
- 24 June 2019
- Published by Springer Nature in Applied Mathematics and Mechanics
- Vol. 40 (9) , 1335-1360
Compensation of stress intensity factors in hollow cylinders containing several cracks under torsion by electro-elastic coating
- 1 January 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 773, 503-510
Investigation into thermal expansion coefficient, thermal conductivity and thermal stability of Al-graphite composite prepared by powder metallurgy
- 1 January 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 773, 503-510
Investigation into thermal expansion coefficient, thermal conductivity and thermal stability of Al-graphite composite prepared by powder metallurgy
- 20 November 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (2) , 025205
A comparative experimental study for determination of residual stress in laminated composites using ring core, incremental hole drilling, and slitting methods
- 20 November 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (2) , 025205
A comparative experimental study for determination of residual stress in laminated composites using ring core, incremental hole drilling, and slitting methods
- 7 September 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (11) , 116511
The effect of alloying elements on fracture resistance of E7010-P1 cellulosic welding electrodes
- 7 September 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (11) , 116511
The effect of alloying elements on fracture resistance of E7010-P1 cellulosic welding electrodes
- 24 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (8) , 085014
Mechanical, microstructural, and fatigue characteristics of hot consolidated Al-SiC nanocomposites
- 24 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (8) , 085014
Mechanical, microstructural, and fatigue characteristics of hot consolidated Al-SiC nanocomposites
- 13 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (8) , 086514
Investigation of mechanical and microstructural properties of AZ31/SiC nanocomposite fabricated by squeeze stir casting
In this paper, AZ31/SiC nanocomposite was fabricated using squeeze stir casting method. 1 wt% SiC nanoparticles were added to the matrix using a novel powder injection system. The melt was stirred by two different speeds (430 and 600 RPM). The nanocomposite was solidified under the 80 MPa pressure. Some of the samples were cooled rapidly by water and some others were normally cooled by ambient air. Mechanical and microstructural properties of the fabricated nanocomposites were investigated. The results show that the controlled injection of nanoparticles using the gas can enhance the wettability and uniform distribution of nanoparticles. Moreover, increasing the stirring speed and cooling rate led to decreasing the grain size, increasing the uniformity of microstructure and improvement of mechanical properties. In the appropriate situation the yield stress, ultimate stress, elongation and micro hardness were increased by about 72%, 80%, 63% and 11%, respectively in comparison with monolithic AZ31 alloy.
- 13 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (8) , 086514
Investigation of mechanical and microstructural properties of AZ31/SiC nanocomposite fabricated by squeeze stir casting
In this paper, AZ31/SiC nanocomposite was fabricated using squeeze stir casting method. 1 wt% SiC nanoparticles were added to the matrix using a novel powder injection system. The melt was stirred by two different speeds (430 and 600 RPM). The nanocomposite was solidified under the 80 MPa pressure. Some of the samples were cooled rapidly by water and some others were normally cooled by ambient air. Mechanical and microstructural properties of the fabricated nanocomposites were investigated. The results show that the controlled injection of nanoparticles using the gas can enhance the wettability and uniform distribution of nanoparticles. Moreover, increasing the stirring speed and cooling rate led to decreasing the grain size, increasing the uniformity of microstructure and improvement of mechanical properties. In the appropriate situation the yield stress, ultimate stress, elongation and micro hardness were increased by about 72%, 80%, 63% and 11%, respectively in comparison with monolithic AZ31 alloy.
- 18 June 2018
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 88 (10) , 1859-1876
A novel approach to calibrate the Drucker–Prager Cap model for Al7075 powder
- 18 June 2018
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 88 (10) , 1859-1876
A novel approach to calibrate the Drucker–Prager Cap model for Al7075 powder