Jun Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jun Yin has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Pär G. Jönsson
Department of Material Science and Engineering KTH Royal Institute of Technology Stockholm SE-100 44 Sweden
3 shared publicationsAlberto N. Conejo
School of Metallurgical and Ecological Engineering University of Science and Technology Beijing (USTB) 30 Xueyuan Road, Haidian District Beijing 100083 P. R. China
2 shared publicationsMikael Ersson
Department of Material Science and Engineering KTH Royal Institute of Technology Stockholm SE-100 44 Sweden
2 shared publications- Mikael Ersson
Materials Science and Engineering KTH Royal Institute of Technology Stockholm Sweden
2 shared publications - Huahai Mao
KTH Royal Inst Technol, Dept Mat Sci & Engn, SE-10044 Stockholm, Sweden
1 shared publication Nils Andersson
Department of Material Science and Engineering KTH Royal Institute of Technology Stockholm SE-100 44 Sweden
1 shared publication
Latest Publications
- Open Access
- 15 May 2021
- Published by Wiley in Steel Research International
- Vol. 92 (10) , 2100102
Numerical Study on the Influence of the Filling Angle on the Fluid Flow during the Ingot Side Teeming Process
High turbulence at the liquid steel−mold flux interface results in mold flux entrapments, which can generate nonmetallic inclusions during the ingot‐casting process. Those nonmetallic inclusions are detrimental to the final steel quality. The teeming process during ingot casting is typically conducted using the uphill teeming method. The authors propose a novel alternative method using a side teeming process, which decreases turbulence at the free surface. To define the optimum operational conditions, a 3D mathematical model is developed to investigate the effect of the filling angle on the motion of the free surface and the resulting shear stresses during the teeming process. The investigated filling angles are 0°, 30°, 45°, 60°, and 90°. The present findings suggest that using the filling angle of 90° between the mold and the runner is an effective way of reducing the number of inclusions due to mold flux entrapments and refractory wear.
- 15 May 2021
- Published by Wiley in Steel Research International
- Vol. 92 (10) , 2100102
Open AccessNumerical Study on the Influence of the Filling Angle on the Fluid Flow during the Ingot Side Teeming Process
High turbulence at the liquid steel−mold flux interface results in mold flux entrapments, which can generate nonmetallic inclusions during the ingot‐casting process. Those nonmetallic inclusions are detrimental to the final steel quality. The teeming process during ingot casting is typically conducted using the uphill teeming method. The authors propose a novel alternative method using a side teeming process, which decreases turbulence at the free surface. To define the optimum operational conditions, a 3D mathematical model is developed to investigate the effect of the filling angle on the motion of the free surface and the resulting shear stresses during the teeming process. The investigated filling angles are 0°, 30°, 45°, 60°, and 90°. The present findings suggest that using the filling angle of 90° between the mold and the runner is an effective way of reducing the number of inclusions due to mold flux entrapments and refractory wear.
- Open Access
- 22 February 2021
- Published by Wiley in Steel Research International
- Vol. 92 (8) , 2000660
Experimental and Numerical Study of the Free Surface During the Side Teeming Ingot Casting Process
The flow pattern affects the interaction between the mold flux and liquid steel, especially during the initial entry of liquid steel into the mold. Strong turbulence can cause mold flux entrapments during the ingot casting process. If this happens, nonmetallic inclusions are generated, which decreases the quality of the final product. Herein, the side teeming process is introduced as an alternative to the traditional uphill teeming process to decrease mold flux entrapments. Both physical experiments and mathematical modeling are conducted to study the free surface. Specifically, the Weber number is also evaluated to predict the possibility of mold flux entrapments at the free surface. The results show that a calmer free surface is formed in the side teeming process compared with the uphill teeming process. Also, the results show that the Reynolds stress model is more suitable to predict the free surface compared with the realizable k–ε model. The present findings strongly suggest that an implementation of a side teeming process would be an effective way of reducing the risk for mold flux entrapments.
- 22 February 2021
- Published by Wiley in Steel Research International
- Vol. 92 (8) , 2000660
Open AccessExperimental and Numerical Study of the Free Surface During the Side Teeming Ingot Casting Process
The flow pattern affects the interaction between the mold flux and liquid steel, especially during the initial entry of liquid steel into the mold. Strong turbulence can cause mold flux entrapments during the ingot casting process. If this happens, nonmetallic inclusions are generated, which decreases the quality of the final product. Herein, the side teeming process is introduced as an alternative to the traditional uphill teeming process to decrease mold flux entrapments. Both physical experiments and mathematical modeling are conducted to study the free surface. Specifically, the Weber number is also evaluated to predict the possibility of mold flux entrapments at the free surface. The results show that a calmer free surface is formed in the side teeming process compared with the uphill teeming process. Also, the results show that the Reynolds stress model is more suitable to predict the free surface compared with the realizable k–ε model. The present findings strongly suggest that an implementation of a side teeming process would be an effective way of reducing the risk for mold flux entrapments.
- Open Access
- 6 February 2020
- Published by Wiley in Steel Research International
- Vol. 91 (6)
An Experimental and Numerical Study of the Free Surface in an Uphill Teeming Ingot Casting Process
The generation of nonmetallic inclusions due to mold flux entrapment is detrimental for the final steel quality in the uphill teeming process. Herein, physical and mathematical modeling using a full‐scale mold is conducted to investigate the change of the hump height and the surface height at the free surface during filling. Moreover, the Weber number is also studied to analyze the tendency of mold flux entrapment at the free surface. The results show that the Reynolds stress model can predict the hump height more accurately compared with the k − ε‐based turbulence models. In addition, the result shows that a lower filling rate can result in a lower hump height as well as less fluctuations of the hump and surface heights. Furthermore, the Weber number for the low flow rate case is lower than 12.3, which indicates a small or no risk for mold flux entrapment. The present findings suggest that a reduction in velocity in the mold entrance region are an effective means of reducing the risk of mold flux entrapment.
- 6 February 2020
- Published by Wiley in Steel Research International
- Vol. 91 (6)
Open AccessAn Experimental and Numerical Study of the Free Surface in an Uphill Teeming Ingot Casting Process
The generation of nonmetallic inclusions due to mold flux entrapment is detrimental for the final steel quality in the uphill teeming process. Herein, physical and mathematical modeling using a full‐scale mold is conducted to investigate the change of the hump height and the surface height at the free surface during filling. Moreover, the Weber number is also studied to analyze the tendency of mold flux entrapment at the free surface. The results show that the Reynolds stress model can predict the hump height more accurately compared with the k − ε‐based turbulence models. In addition, the result shows that a lower filling rate can result in a lower hump height as well as less fluctuations of the hump and surface heights. Furthermore, the Weber number for the low flow rate case is lower than 12.3, which indicates a small or no risk for mold flux entrapment. The present findings suggest that a reduction in velocity in the mold entrance region are an effective means of reducing the risk of mold flux entrapment.
- Open Access
Mathematical Modelling of the Initial Mold Filling with Utilization of an Angled Runner
The flow pattern plays a crucial role in the uphill teeming process. The non-metallic inclusion generation due to interaction with the mold flux is believed to be influenced by the flow pattern. In this study, a three-dimensional mathematical model of the filling of a gating system for 10, 20, and 30 degrees angled runners was used to predict the fluid flow characteristics. Moreover, a mathematical model with a horizontal runner was applied as a reference. The predictions indicate that the angled-runner-design decreases the hump height during the initial filling stage, which results in less entrapment of mold flux into the mold. Nevertheless, increasing the angle of runner can result in a lower hump height, while the 30 degree angled runner gives a much more stable increase of the hump height during the initial filling stage. Besides CFD calculations, some thermodynamic calculations are taken into account for the chemical reactions between liquid steel and gas. The results show that the bubble shrinks due to the fact that N and O are dissolved into steel. The present findings strongly suggest that changing the horizontal runner to an angled runner would be an effective means of reducing flow unevenness during the initial filling of ingots, if the added steel losses are deemed acceptable.
Open AccessMathematical Modelling of the Initial Mold Filling with Utilization of an Angled Runner
The flow pattern plays a crucial role in the uphill teeming process. The non-metallic inclusion generation due to interaction with the mold flux is believed to be influenced by the flow pattern. In this study, a three-dimensional mathematical model of the filling of a gating system for 10, 20, and 30 degrees angled runners was used to predict the fluid flow characteristics. Moreover, a mathematical model with a horizontal runner was applied as a reference. The predictions indicate that the angled-runner-design decreases the hump height during the initial filling stage, which results in less entrapment of mold flux into the mold. Nevertheless, increasing the angle of runner can result in a lower hump height, while the 30 degree angled runner gives a much more stable increase of the hump height during the initial filling stage. Besides CFD calculations, some thermodynamic calculations are taken into account for the chemical reactions between liquid steel and gas. The results show that the bubble shrinks due to the fact that N and O are dissolved into steel. The present findings strongly suggest that changing the horizontal runner to an angled runner would be an effective means of reducing flow unevenness during the initial filling of ingots, if the added steel losses are deemed acceptable.