PWPeng Wang

Peng Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Peng Wang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Lateral Performance of Semi-Rigid Steel Frames with Precast Knee Bracing Systems: Testing and Finite Element Analysis

    by Jianzhong Lin, Zhimin Yu, Yongguo Zhong, Zejia Zhou, Peng Wang

    In this paper, the synergistic strengthening mechanism of a new type of prefabricated knee brace to semi-rigid steel frame lateral resistance was experimentally and numerically analyzed. Five full-scale specimens with a control steel frame and four knee-braced configurations were tested under pseudo-static cyclic loading in order to understand the stiffness evolution, failure mode, and energy dissipation characteristics of the specimens. Results show the following: (1) The innovative integrated knee braces increase initial lateral stiffness and yield capacity by 184–242% and 91–154% compared to conventional semi-rigid frames with acceptable ductility; (2) Three different failure modes coupled brace-joint yielding (Type I), brace dominated instability (Type II) and beam buckling brace connections (Type III) are identified; (3) Finite element simulations using ABAQUS with isotropic/kinetic hardening models show good agreement with experiments for their hysteretic responses confirming In particular the ultimate failure location is identified at the lateral screw holes of beam flanges located near brace supports where the local stress is greater than 1.8fy. The study further proposes a BIM-integrated design workflow. These results give a theoretical basis and some practical recommendations for the application of knee-braced semi-rigid systems in earthquake-resistant steel buildings.

  • Open Access

    Seismic Behavior of Beam-Connected Precast Walls with Innovative Concealed Steel Bracings: Experimental Insights and Numerical Study

    by Yongguo Zhong, Zhimin Yu, Zejia Zhou, Jianzhong Lin, Peng Wang

    In order to improve the seismic performance of traditional precast lightweight walls, a new precast concrete wall with beam connection and embedded steel support is proposed in this study. Six 2/3-scale specimens were designed for a quasi-static cyclic loading test, and a numerical study was carried out. Key variables include shear span ratio (0.8–1.6), wall thickness (120–200 mm), concrete strength (C25–C40), and concealed column configuration. The experimental results reveal three distinct failure modes, specifically, brace buckling, weld fracture at the lower joints, and bolt shear failure. The system shows excellent ductility (displacement ductility coefficient μ = 3.2–4.1) and energy dissipation capacity (equivalent viscous damping ratio ξ = 0.28–0.35), and its performance is 30–40% higher than that of traditional reinforced concrete walls and close to that of steel plate shear walls. The shear span ratio is reduced by 50%, the shear bearing capacity is increased by 16%, but the peak displacement is halved, and the peak load of concealed column is increased by 57%. The finite element analysis verified the experimental trends and emphasized that the shear capacity can be increased by 12–18% by widening the steel brace (relative to thickening) under the condition of constant steel volume. The results demonstrate that BIM-driven design is very important for solving connection conflicts and ensuring constructability. Parameter research shows that when the concrete strength is greater than C30, the yield load increases by 15–20%, but the influence on the ultimate bearing capacity is minimal. These findings provide an operational guide for the implementation of high-performance prefabricated walls in earthquake-resistant steel structures, and balance the details of constructability through support, connection, and BIM.


  • Open Access

    A Technique for Optimizing the Sequences Yielding under Load of Concentrically-Braced Steel Frames

    by Bin Li, Zhan Wang, Yanjing Fan, Jianrong Pan, Peng Wang, Zhenfeng Zhou

    Concentrically-braced steel framing is widely used in tall buildings. Designing with adequate but not excessive seismic resistance is a challenge because of the limited experience of seismic failure and the huge variety of components used. A quantitative method for defining an acceptable range of component parameters is proposed and tested using published experimental data and finite element modeling. The method involves the structural yield mechanism control method of the steel concentrically-braced frame. It is proposed by inequality iteration of different structural components’ bearing capacities. It generates acceptable ranges for the parameters defining the properties of the columns, beams, and braces. The test results show that concentrically-braced steel frames designed within the recommended ranges will have the desired sequence of component yielding. The sequence is, however, highly sensitive to components’ parameter values. In practical engineering stochastic variability in the parameters must be considered.

  • Open Access

    Finite-Element Analysis of High-Strength Steel Extended End-Plate Connections under Cyclic Loading

    by Tao Lin, Zhan Wang, Fangxin Hu, Peng Wang

    In order to examine the seismic behavior of high-strength steel extended end-plate connections, a three-dimensional efficient finite-element model in Abaqus was established subjected to cyclic loading at the beam end. Geometrical dimensions, boundary conditions, element types, contact properties between the bolts, end-plate and column flange, and material cyclic constitutive models were described in detail. Geometry and material nonlinearity were adequately considered. In particular, a cyclic plasticity model for high-strength steels was employed that was easily calibrated based on the tension coupon test, so as to describe the complicated cyclic hardening and softening response. The simulated results of the finite-element model were compared to the test ones in terms of both deformation modes and hysteresis loops. The results showed that the bending deformation of the end-plate and column flange was accurately captured, and the gap phenomena among the bolt nuts, the end-plate, and column flange was described in a satisfactory manner as well. The hysteresis loops from the simulation agreed well with the test results, reproducing the pinched shape due to the end-plate gap evolution under cyclic loading as well as the quite plump shape with stable energy dissipation when the panel zone dominated the cyclic response. Therefore, the accuracy of the finite-element model was verified and it provided a strong benchmark tool for investigating the cyclic or seismic performance of this kind of connection. The connection failure including the bolt fracture and cracking in the end-plate needs further numerical study by calibrating accurate material failure models for high-strength steels and bolts.


  • Behavior of exposed column-base connections with four internal anchor bolts under seismic loading

    by Jianrong Pan, Ruike Huang, Jing Xu, Peng Wang, Zhan Wang, Jin Chen


  • Open Access

    Experimental and numerical investigation of stiffened angle connection in a minor axis

    by Peng Wang, Jianrong Pan, Zhan Wang, Bin Li, Jiangui Qin

    The bolted angle connections which are simple, fast, cost-effective, high quality, and no site welding have been recognized as their excellent performance. The moment-rotation behavior of both major and minor axis should be both taken into considering, however, the lack of research on minor axis limits the more comprehensive application. Five monotonic tests were carried out to investigate the influence under different parameters, and a new type connection were considered and detailed. Refined finite element models were built to validate the experimental results and to do several parametric analyses on initial rotational stiffness and plastic moment resistance, including of a presence of stiffened seat angle, angle thickness, and prying force. Furthermore, a new simplified plate method was proposed for calculating stiffness of stiffened angle and web in bending. The stiffened angle gives a significant increase at the moment-resisting capacity and the initial stiffness, the ultimate rotation of all tested specimens was beyond 0.067rad. The initial stiffness and plastic moment resistance of the joints were also controlled by the column web. The presence of the stiffener in the compression zone has the none effect on initial stiffness. The numerical analysis has captured the failure reason for weld and more attention should be paid to welding of stiffener in engineering design and practice. Adding stiffener at the top-and-seat angle joint can reduce the prying force of bolt, but it still cannot be ignored. The theoretical results were in good agreement with the experimental data and finite element results; therefore, it can be used to guide the design and selection of joints.


  • Open Access

    Error Analysis Method of Geometrically Incomplete Similarity of End-Plate Connection Based on Linear Regression

    by Dongzhuo Zhao, Zhan Wang, Jianrong Pan, Peng Wang

    Due to the limitations of processing errors, test conditions and other factors, geometric similarity errors in scale tests of steel structure joints are difficult to avoid, but the research on this error is little known. Based on the similarity theory and the basic idea of the component method, this paper deduces the similar macro conditions of beam–column end-plate connections and derives the main influencing factors of geometric similarity of these types of structures. Aiming at the factor of the thickness of the end-plate, the formation mechanism of the geometrically incomplete similarity error of this type of node was studied. Through the establishment of accurate finite element models for parameterized analysis, the influence of end plate thickness on incomplete similarity error is analyzed. Based on this model and linear regression analysis methods, the prediction formulas of geometric incomplete similarity errors of beam–column end-plate connections have been established, which can significantly reduce similar errors due to end plate thickness. This article aims to propose a method for simulating the distribution of incompletely similar errors and provide a reference for the research of similar problems.


  • Open Access

    Seismic Behavior of a Novel Blind Bolted Flush End-Plate Connection to Strengthened Concrete-Filled Steel Tube Columns

    by Yihuan Wang, Zhan Wang, Jianrong Pan, Peng Wang

    Modified blind bolts (Hollo-Bolt) and a locally strengthened steel tube column in the panel zone were created to overcome the moment-resisting problem for the bolted connections between concrete-filled hollow section columns and open section beams and to enhance the performance of connections. The cyclic loading was conducted on a total of six modified anchored blind bolted flush end-plate connections to concrete-filled steel tube (CFST) columns. The key parameters investigated were the tube wall thickness, end-plate thickness, blind bolt anchorage method, and beam section. The failure mode, hysteretic behavior, strength, stiffness, ductility, and energy dissipation capacity of the connections were analyzed and evaluated with all details. The results indicated that connections with modified anchored blind bolts and locally strengthened steel tubes could avoid the premature failure of CFST column and exhibit an improved behavior with a favorable strength, stiffness, and stiffness degradation. The test observations reveal two representative failure modes, and the tube wall thickness and blind bolt anchorage method have a significant effect on the resultant failure mode. Moreover, the use of thin endplate and weak beam can effectively enhance the hysteretic behavior of joints, ductility, and energy dissipation capacity; and the change in anchoring method has little effect on the stiffness. Finite element (FE) analysis models were established for the aforementioned connections. The numerical models were validated against the experimental results and exhibited good agreement. Finally, based on the component method, an initial stiffness calculation method was established for the connections.


  • Open Access

    Cyclic Behavior of Anchored Blind-Bolted Extended End-Plate Joints to CFST Columns

    by Yihuan Wang, Zhan Wang, Jianrong Pan, Peng Wang, JianGui Qin, Shizhe Chen

    As the square steel tube in the tension zone is always the weakest part of moment-resisting joints, modified blind bolts (Hollo-Bolts) and a locally strengthened steel tube in the panel zone were adopted to enhance the joint performance. Cyclic loading tests were carried out on eight anchored blind-bolted extended end-plate joints between square concrete-filled steel tube (CFST) columns and steel beams. The test parameters included the end-plate thickness, steel tube wall thickness, beam section size, local strengthening connection method, blind bolt anchorage method, and stiffeners. The failure mode, hysteretic behavior, stiffness, strength, ductility, strength degradation, stiffness degradation, and energy dissipation capacity of the joints were studied and analyzed. The test results showed that the application of anchored blind bolts and a locally strengthened steel tube can fully utilize the bolt strength and significantly improve the joint performance, especially in terms of strength and strength degradation. The test observations revealed three typical failure modes for the joints, and the failure mode depended on the weakest component. In addition, the local reinforcement of C-channel and change in the anchorage method had a limited effect on the initial stiffness. Greater end-plate thickness and the use of stiffeners significantly increased the joint stiffness and decreased the rate of stiffness degradation. The use of stiffeners also significantly enhanced the ductility and energy dissipation by moving plastic hinge outward from the joints. Finally, finite element analysis (FEA) models were developed and validated against the experimental results, and the stress distribution and force transfer pattern were investigated.


  • Open Access

    An Analytical Study of Square CFT Columns in Bracing Connection Subjected to Axial Loading

    by Jianrong Pan, Peng Wang, Yanjun Zheng, Zhan Wang, Deming Liu

    This paper presents the behavior of square concrete‐filled tubular (CFT) columns with different penetrating gusset plates under axial load. Load transfer mechanism in the CFT columns including load distribution between gusset plate and core concrete and composite action of the gusset plate and steel tube was investigated. Experimental results showed that the axial load can be transferred from the bottom edge, ribs, and the hole of the gusset plate to core concrete through the bearing mechanism. Adding ribs or a hole on the gusset plate can efficiently facilitate load transmission and improve the composite action. Numerical models were established to determine the distribution of axial forces among members in the square CFT column. Then, revised coefficients of elastic modulus for the square CFT column with the gusset plate were proposed.