Willie du Preez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Willie du Preez has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Maina Maringa
Department of Mechanical and Mechatronics Engineering, Central University of Technology
16 shared publications - Amos Muiruri
Department of Mechanical and Mechatronics Engineering, Central University of Technology, Bloemfontein 9301, South Africa
14 shared publications - Thywill Cephas Dzogbewu
Department of Mechanical and Mechatronics Engineering, Faculty of Engineering, Built Environment and Information Technology, Central University of Technology, Bloemfontein, South Africa
5 shared publications - Jacques Combrinck
Department of Mechanical and Mechatronics Engineering, Faculty of Engineering, Built Environment and Information Technology, Central University of Technology Free State, Bloemfontein 9300, South Africa
3 shared publications M Maringa
Central University of Technology
3 shared publications- Deon de Beer
Centre for Rapid Prototyping and Manufacturing, Central University of Technology, Bloemfontein, South Africa
2 shared publications
Latest Publications
- Open Access
- 17 April 2026
- Published by MDPI AG in Materials Proceedings
- Vol. 31  (1) , 17
Optimization of the Design and Improvement of the Mechanical Properties of a Polymeric Heart Valve Through Computational Modelling
There is a need to develop a native human heart valve substitute that is optimally designed, cost-effective, possesses an adequate lifespan, requires minimal anticoagulant medication, and features minimal turbulence and pressure variations within the cardiovascular system. Polymer heart valves, due to their design which allows blood to flow centrally through the valve, are the most promising prosthetic heart valve type for future hemodynamic enhancement. The search continues to mitigate premature mechanical failure of polymer valves and to improve their effectiveness through in vitro experiments. The leaflet must withstand repeated stress from millions of opening and closing cycles without degrading or compromising its functionality. In exploring new materials, two different carbothane materials were employed to improve valve durability and facilitate fabrication utilizing compression moulding. Computational modelling and finite element analysis were used to simulate the response of various materials, designs, and manufacturing techniques to complex loading conditions encountered by polymer valves. A systematic thickening of leaflet regions with higher stress concentrations was implemented to address the design limitations of a reverse-engineered dip-moulded polymer valves. The optimized geometry and structure of the polymer valve, which promote smooth, less turbulent blood flow, were evaluated to determine mechanical stresses in the leaflets and the valve’s hemodynamic performance. The study concluded that the systematic increase in the thickness of leaflet regions highly affected by stress concentration significantly reduced stress distribution and improved the valve’s hemodynamic performance. Prototypes were manufactured using a combination of additive manufacturing and compression moulding to ensure precise geometric specifications. It was concluded that computational modelling reduced the need for extensive physical prototyping and testing, which can be time-consuming and costly.
- 17 April 2026
- Published by MDPI AG in Materials Proceedings
- Vol. 31  (1) , 17
Open AccessOptimization of the Design and Improvement of the Mechanical Properties of a Polymeric Heart Valve Through Computational Modelling
There is a need to develop a native human heart valve substitute that is optimally designed, cost-effective, possesses an adequate lifespan, requires minimal anticoagulant medication, and features minimal turbulence and pressure variations within the cardiovascular system. Polymer heart valves, due to their design which allows blood to flow centrally through the valve, are the most promising prosthetic heart valve type for future hemodynamic enhancement. The search continues to mitigate premature mechanical failure of polymer valves and to improve their effectiveness through in vitro experiments. The leaflet must withstand repeated stress from millions of opening and closing cycles without degrading or compromising its functionality. In exploring new materials, two different carbothane materials were employed to improve valve durability and facilitate fabrication utilizing compression moulding. Computational modelling and finite element analysis were used to simulate the response of various materials, designs, and manufacturing techniques to complex loading conditions encountered by polymer valves. A systematic thickening of leaflet regions with higher stress concentrations was implemented to address the design limitations of a reverse-engineered dip-moulded polymer valves. The optimized geometry and structure of the polymer valve, which promote smooth, less turbulent blood flow, were evaluated to determine mechanical stresses in the leaflets and the valve’s hemodynamic performance. The study concluded that the systematic increase in the thickness of leaflet regions highly affected by stress concentration significantly reduced stress distribution and improved the valve’s hemodynamic performance. Prototypes were manufactured using a combination of additive manufacturing and compression moulding to ensure precise geometric specifications. It was concluded that computational modelling reduced the need for extensive physical prototyping and testing, which can be time-consuming and costly.
- Open Access
- 14 April 2026
- Published by MDPI AG in Materials Proceedings
- Vol. 31  (1) , 4
Lithography-Based Ceramic Manufacturing of Diamond Lattice Structure for Bone Regeneration Scaffolds
This study investigates the mechanical and biological properties of diamond lattice structure produced through lithography-based ceramic manufacturing, an additive manufacturing technique. HA480 specimens, cubes of 5 × 5 × 5 mm, were manufactured with appropriate pore sizes and porosity. Printed HA480 specimens were tested and analysed for compression strength, cell proliferation, and cell attachment. The printed cubes displayed interconnected pore geometry. A set of ten HA480 diamond lattice structure specimens were compressed until failure to obtain a compressive strength of 10.7 MPa. HA480 solid scaffolds were seeded with the human osteoblast cell line hFOB 1.19 cells. The fluorescence level results were higher on day 3 and decreased on days 5 and 7. Cell attachment was observed from day 1 to day 7. In this study, biodegradation was also evaluated with diamond lattice structure immersed in the simulated body fluid for days 1 and 7 and 28 days. The Scanning Electron Microscopy showed precipitation after 7 days immersion and evidence of apatite after 28 days on the HA480 surface. The findings provide evidence that HA480 reacts with biological fluids and can be used as a material for bone regeneration scaffold.
- 14 April 2026
- Published by MDPI AG in Materials Proceedings
- Vol. 31  (1) , 4
Open AccessLithography-Based Ceramic Manufacturing of Diamond Lattice Structure for Bone Regeneration Scaffolds
This study investigates the mechanical and biological properties of diamond lattice structure produced through lithography-based ceramic manufacturing, an additive manufacturing technique. HA480 specimens, cubes of 5 × 5 × 5 mm, were manufactured with appropriate pore sizes and porosity. Printed HA480 specimens were tested and analysed for compression strength, cell proliferation, and cell attachment. The printed cubes displayed interconnected pore geometry. A set of ten HA480 diamond lattice structure specimens were compressed until failure to obtain a compressive strength of 10.7 MPa. HA480 solid scaffolds were seeded with the human osteoblast cell line hFOB 1.19 cells. The fluorescence level results were higher on day 3 and decreased on days 5 and 7. Cell attachment was observed from day 1 to day 7. In this study, biodegradation was also evaluated with diamond lattice structure immersed in the simulated body fluid for days 1 and 7 and 28 days. The Scanning Electron Microscopy showed precipitation after 7 days immersion and evidence of apatite after 28 days on the HA480 surface. The findings provide evidence that HA480 reacts with biological fluids and can be used as a material for bone regeneration scaffold.
- Open Access
- 9 December 2024
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 406, 07005
Towards the design qualification of removable partial dentures produced through laser powder bed fusion of cobalt-chrome – a case study
Part qualification, a component of quality assurance, is a critical requirement for components produced through additive manufacturing (AM) and intended to replace traditionally manufactured qualified industrial components. The part qualification process is broad and can cover requirements which are linked to individual additive manufactured parts, machines, materials and process parameters based on overall risk. This paper reviews the design qualification process for removable partial dentures (RPDs) fabricated through laser powder bed fusion (LPBF) using cobalt- chromium (Co-Cr) alloys. Key considerations during the manufacturing process which ensure the reliability and efficacy of LPBF-produced RPDs are discussed. With reference to the dental industry, one such consideration is the need for patient comfort which is derived from the fit of the RPD. This paper further demonstrates the use of design qualification (DQ) to define the fit of LPBF RPDs according to dental requirements. The DQ was instrumental in defining a suitable material fit for RPD produced using the LPBF of Co-Cr.
- 9 December 2024
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 406, 07005
Open AccessTowards the design qualification of removable partial dentures produced through laser powder bed fusion of cobalt-chrome – a case study
Part qualification, a component of quality assurance, is a critical requirement for components produced through additive manufacturing (AM) and intended to replace traditionally manufactured qualified industrial components. The part qualification process is broad and can cover requirements which are linked to individual additive manufactured parts, machines, materials and process parameters based on overall risk. This paper reviews the design qualification process for removable partial dentures (RPDs) fabricated through laser powder bed fusion (LPBF) using cobalt- chromium (Co-Cr) alloys. Key considerations during the manufacturing process which ensure the reliability and efficacy of LPBF-produced RPDs are discussed. With reference to the dental industry, one such consideration is the need for patient comfort which is derived from the fit of the RPD. This paper further demonstrates the use of design qualification (DQ) to define the fit of LPBF RPDs according to dental requirements. The DQ was instrumental in defining a suitable material fit for RPD produced using the LPBF of Co-Cr.
- Open Access
- 10 August 2024
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 29  (4) , 64
Evaluation of the Impact of Stress Distribution on Polyurethane Trileaflet Heart Valve Leaflets in the Open Configuration by Employing Numerical Simulation
It is costly and time-consuming to design and manufacture functional polyurethane heart valve prototypes, to evaluate and comprehend their hemodynamic behaviour. To enhance the rapid and effective design of replacement heart valves, to meet the minimum criteria of FDA and ISO regulations and specifications, and to reduce the length of required clinical testing, computational fluid dynamics (CFD) and finite element analysis (FEA) were used. The results revealed that when the flexibility of the stent was taken into consideration with a uniform leaflet thickness, stress concentration regions that were present close to the commissural attachment were greatly diminished. Furthermore, it was found that the stress on the leaflets was directly impacted by the effect of reducing the post height on both rigid and flexible stents. When varying the leaflet thickness was considered, the high-stress distribution close to the commissures appeared to reduce at thicker leaflet regions. However, thicker leaflets may result in a stiffer valve with a corresponding increase in pressure drop. It was concluded that a leaflet with predefined varying thickness may be a better option.
- 10 August 2024
- Published by MDPI AG in Mathematical and Computational Applications
- Vol. 29  (4) , 64
Open AccessEvaluation of the Impact of Stress Distribution on Polyurethane Trileaflet Heart Valve Leaflets in the Open Configuration by Employing Numerical Simulation
It is costly and time-consuming to design and manufacture functional polyurethane heart valve prototypes, to evaluate and comprehend their hemodynamic behaviour. To enhance the rapid and effective design of replacement heart valves, to meet the minimum criteria of FDA and ISO regulations and specifications, and to reduce the length of required clinical testing, computational fluid dynamics (CFD) and finite element analysis (FEA) were used. The results revealed that when the flexibility of the stent was taken into consideration with a uniform leaflet thickness, stress concentration regions that were present close to the commissural attachment were greatly diminished. Furthermore, it was found that the stress on the leaflets was directly impacted by the effect of reducing the post height on both rigid and flexible stents. When varying the leaflet thickness was considered, the high-stress distribution close to the commissures appeared to reduce at thicker leaflet regions. However, thicker leaflets may result in a stiffer valve with a corresponding increase in pressure drop. It was concluded that a leaflet with predefined varying thickness may be a better option.
- Open Access
A Comparative Analysis of Low and High SiC Volume Fraction Additively Manufactured SiC/Ti6Al4V(ELI) Composites Based on the Best Process Parameters of Laser Power, Scanning Speed and Hatch Distance
Silicon carbide (SiC) exhibits intriguing thermo-physical properties such as higher heat capacity and conductivity, as well as a lower density than Ti6Al4V(ELI). These properties make SiC a good candidate for the reinforcement of Ti6Al4V(ELI) with respect to its use as a heat shield in aero turbines to increase their efficiency. The traditional materials used in aircraft structures were required to have a combination of good mechanical properties such as strength, stiffness, and hardness and low weight, as well as low thermo-physical properties such as coefficient of thermal expansion (CTE) and thermal conductivity. The alloy Ti6Al4V(ELI) has a density of 4.45 g/cm3, which is lower than that of structural steel (7.4 g/cm3) and higher than that of aluminium (2.5 g/cm3). Lower density benefits light weighting. Aluminium is the lightest of the traditional materials used but has relatively low strength. The CTE of SiC of 4.6 × 10−6/K is lower than that of Ti6Al4V(ELI) of 8.6 × 10−6/K, while the density of SiC of 3.21 g/cm3 is lower than that of Ti6Al4V(ELI) of 4.45 g/cm3. Therefore, from the theory of composites, SiC/Ti6Al4V(ELI) composites are expected to have lower densities and CTEs than those of Ti6Al4V(ELI), thus providing for lightweighting and less thermal related buckling or separation at their joints with carbon/epoxy resin panels. The specific strength, stiffness, and Knoop hardness of SiC of 75–490 kNm/kg, 132 MNm/kg, and 600–3800 GPa, respectively, are generally larger than those of Ti6Al4V(ELI) of 211 KNm/kg, 24 MNm/kg, and 880 GPa, respectively. Therefore, investigating reinforcement of Ti6Al4V(ELI) with SiC particles is worthwhile as it will lead to the formation of composites that are stronger, stiffer, harder, and lighter, with lower values of CTE. For additive manufacturing, this requires initial studies to optimise the process parameters of laser power and scanning speed for single tracks. To print single tracks in the present work, different laser powers ranging from 100 W to 350 W and scanning speeds ranging from 0.3 m/s to 2.7 m/s were used for different SiC volume fraction values of values. To print single layers, different values of hatch distance were used together with the best values of laser power and scanning speed determined elsewhere by the authors for different volume fractions of SiC. Through optical microscopy, the built tracks and their cross sections were examined. By using laser power and scanning speeds of 200 W and 1.2 m/s, and 150 W and 0.8 m/s, respectively, the best tracks at 5% and 10% volume fractions were obtained, whereas the best tracks at 25% volume fraction were achieved using a laser power of 200 W and a scanning speed of 0.5 m/s. Furthermore, the results showed that the maximum SiC volume percentage of 30% resulted in limited or no penetration. Therefore, it is concluded from the study that parts with improved mechanical properties can be produced at SiC volume fractions ranging from 5% to 25%, while parts produced at the high volume fraction of 30% would have unacceptable mechanical qualities for the final part.
Open AccessA Comparative Analysis of Low and High SiC Volume Fraction Additively Manufactured SiC/Ti6Al4V(ELI) Composites Based on the Best Process Parameters of Laser Power, Scanning Speed and Hatch Distance
Silicon carbide (SiC) exhibits intriguing thermo-physical properties such as higher heat capacity and conductivity, as well as a lower density than Ti6Al4V(ELI). These properties make SiC a good candidate for the reinforcement of Ti6Al4V(ELI) with respect to its use as a heat shield in aero turbines to increase their efficiency. The traditional materials used in aircraft structures were required to have a combination of good mechanical properties such as strength, stiffness, and hardness and low weight, as well as low thermo-physical properties such as coefficient of thermal expansion (CTE) and thermal conductivity. The alloy Ti6Al4V(ELI) has a density of 4.45 g/cm3, which is lower than that of structural steel (7.4 g/cm3) and higher than that of aluminium (2.5 g/cm3). Lower density benefits light weighting. Aluminium is the lightest of the traditional materials used but has relatively low strength. The CTE of SiC of 4.6 × 10−6/K is lower than that of Ti6Al4V(ELI) of 8.6 × 10−6/K, while the density of SiC of 3.21 g/cm3 is lower than that of Ti6Al4V(ELI) of 4.45 g/cm3. Therefore, from the theory of composites, SiC/Ti6Al4V(ELI) composites are expected to have lower densities and CTEs than those of Ti6Al4V(ELI), thus providing for lightweighting and less thermal related buckling or separation at their joints with carbon/epoxy resin panels. The specific strength, stiffness, and Knoop hardness of SiC of 75–490 kNm/kg, 132 MNm/kg, and 600–3800 GPa, respectively, are generally larger than those of Ti6Al4V(ELI) of 211 KNm/kg, 24 MNm/kg, and 880 GPa, respectively. Therefore, investigating reinforcement of Ti6Al4V(ELI) with SiC particles is worthwhile as it will lead to the formation of composites that are stronger, stiffer, harder, and lighter, with lower values of CTE. For additive manufacturing, this requires initial studies to optimise the process parameters of laser power and scanning speed for single tracks. To print single tracks in the present work, different laser powers ranging from 100 W to 350 W and scanning speeds ranging from 0.3 m/s to 2.7 m/s were used for different SiC volume fraction values of values. To print single layers, different values of hatch distance were used together with the best values of laser power and scanning speed determined elsewhere by the authors for different volume fractions of SiC. Through optical microscopy, the built tracks and their cross sections were examined. By using laser power and scanning speeds of 200 W and 1.2 m/s, and 150 W and 0.8 m/s, respectively, the best tracks at 5% and 10% volume fractions were obtained, whereas the best tracks at 25% volume fraction were achieved using a laser power of 200 W and a scanning speed of 0.5 m/s. Furthermore, the results showed that the maximum SiC volume percentage of 30% resulted in limited or no penetration. Therefore, it is concluded from the study that parts with improved mechanical properties can be produced at SiC volume fractions ranging from 5% to 25%, while parts produced at the high volume fraction of 30% would have unacceptable mechanical qualities for the final part.
- Open Access
- 17 May 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14  (10) , 4261
Effects of Quasi-Static Strain Rate and Temperature on the Microstructural Features of Post-Processed Microstructures of Laser Powder Bed Fusion Ti6Al4V Alloy
This study documents an investigation of the flow stress properties and microstructural features of Ti6Al4V (ELI) alloy produced using laser powder bed fusion (LPBF). Selected heat treatment strategies were applied to the material to obtain different microstructures. The influence of quasi-static strain rates and temperature on the obtained microstructures of this material and their strain hardening properties are documented in this study. All microstructures of the alloy formed in this study were found to be sensitive to quasi-static strain rates and temperatures, where their flow stresses increased with increasing strain rate and decreased for tests conducted at elevated temperatures. The strain hardening rates of the fine microstructures were found to be high compared to those of coarse microstructures. The strain hardening rates for the various forms of LPBF Ti6Al4V (ELI) examined here were found to diminish with increasing test temperature. Though the deformed surfaces of the built samples were largely dominated by adiabatic shear bands (ASBs), the absence of ASBs was noted for all samples tested at a temperature of 500 °C and an imposed strain of 30%.
- 17 May 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14  (10) , 4261
Open AccessEffects of Quasi-Static Strain Rate and Temperature on the Microstructural Features of Post-Processed Microstructures of Laser Powder Bed Fusion Ti6Al4V Alloy
This study documents an investigation of the flow stress properties and microstructural features of Ti6Al4V (ELI) alloy produced using laser powder bed fusion (LPBF). Selected heat treatment strategies were applied to the material to obtain different microstructures. The influence of quasi-static strain rates and temperature on the obtained microstructures of this material and their strain hardening properties are documented in this study. All microstructures of the alloy formed in this study were found to be sensitive to quasi-static strain rates and temperatures, where their flow stresses increased with increasing strain rate and decreased for tests conducted at elevated temperatures. The strain hardening rates of the fine microstructures were found to be high compared to those of coarse microstructures. The strain hardening rates for the various forms of LPBF Ti6Al4V (ELI) examined here were found to diminish with increasing test temperature. Though the deformed surfaces of the built samples were largely dominated by adiabatic shear bands (ASBs), the absence of ASBs was noted for all samples tested at a temperature of 500 °C and an imposed strain of 30%.
- Open Access
- 25 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13  (9) , 5372
Numerical Simulation of the Taylor Impact Test for Laser Powder Bed Fusion Parts Based on Microstructural Internal State Variables
The response of any engineering design components to stresses should be predictable, While the response of a material to complex loading, such as high strain rates experienced during service, is difficult to represent with simple tests, the Taylor impact test is one of a number of tests devised for high strain rate complex loading. To expedite the acceptance of LPBF Ti6Al4V (ELI) for use in demanding structural applications, there is a need to develop numerical models based on the internal microstructural state variables to predict the performance of the alloy over a wide range of high strain rates using such complex tests. This paper documents the numerical simulation of Taylor impact tests for direct metal laser-sintered and post-processed Ti6Al4V (ELI—Extra Low Interstitial) alloy. A microstructural variable-based constitutive model was used to predict the mechanical properties (stresses and evolution of plastic strains) of the material. The corresponding material parameters of the model were based on the specific microstructure obtained upon post-process heat treatment. The model was first implemented as a user material subroutine in the explicit finite element program ABAQUS using the VUHARD subroutine. Subsequently, the symmetrical Taylor impact tests of Laser Powder Bed Fusion (LPBF) Ti6Al4V (ELI) parts were numerically simulated using the VUHARD subroutine at different impact velocities. The equivalent von Mises stress and plastic strain obtained from numerical simulations were compared with the analytical solutions based on the strain rates obtained. It was shown that the instantaneous and average absolute errors between the numerical and analytical values of the model were generally less than 5%. The mushroom end, commonly observed in a Taylor test specimen, was also seen in the numerical model.
- 25 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13  (9) , 5372
Open AccessNumerical Simulation of the Taylor Impact Test for Laser Powder Bed Fusion Parts Based on Microstructural Internal State Variables
The response of any engineering design components to stresses should be predictable, While the response of a material to complex loading, such as high strain rates experienced during service, is difficult to represent with simple tests, the Taylor impact test is one of a number of tests devised for high strain rate complex loading. To expedite the acceptance of LPBF Ti6Al4V (ELI) for use in demanding structural applications, there is a need to develop numerical models based on the internal microstructural state variables to predict the performance of the alloy over a wide range of high strain rates using such complex tests. This paper documents the numerical simulation of Taylor impact tests for direct metal laser-sintered and post-processed Ti6Al4V (ELI—Extra Low Interstitial) alloy. A microstructural variable-based constitutive model was used to predict the mechanical properties (stresses and evolution of plastic strains) of the material. The corresponding material parameters of the model were based on the specific microstructure obtained upon post-process heat treatment. The model was first implemented as a user material subroutine in the explicit finite element program ABAQUS using the VUHARD subroutine. Subsequently, the symmetrical Taylor impact tests of Laser Powder Bed Fusion (LPBF) Ti6Al4V (ELI) parts were numerically simulated using the VUHARD subroutine at different impact velocities. The equivalent von Mises stress and plastic strain obtained from numerical simulations were compared with the analytical solutions based on the strain rates obtained. It was shown that the instantaneous and average absolute errors between the numerical and analytical values of the model were generally less than 5%. The mushroom end, commonly observed in a Taylor test specimen, was also seen in the numerical model.
- 12 December 2022
- Published by Springer Nature in JOM
- Vol. 75  (3) , 806-815
An Investigation into the Optimization of the Selective Laser Melting Process Parameters for Ti6Al4V Through Numerical Modelling
- 12 December 2022
- Published by Springer Nature in JOM
- Vol. 75  (3) , 806-815
An Investigation into the Optimization of the Selective Laser Melting Process Parameters for Ti6Al4V Through Numerical Modelling
- Open Access
- 1 December 2022
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 370, 01003
Influence of selective laser melting process parameters on the characteristics of SiC/Ti6Al4V(ELI) single tracks
Process parameters of selective laser melting, such as track height, track width and depth of penetration, affect the characteristics of laser fused single tracks. The properties of additively manufactured 3D parts depend strongly on the quality of laser melted single tracks and resultant single layers. Layers formed with a good depth of laser penetration provide strong bonding between consecutive layers and the substrate. Poor depth of laser penetration leads to delamination of layers. In this study the effect of the critical process parameters of laser power, laser scanning speed, and laser linear energy density on the characteristics of SiC/Ti6Al4V(ELI) single tracks at different SiC volume fractions (5 %, 10 %, 15 %, 20 %, 25 % and 30%) was investigated. Phenomena, such as the keyhole effect, pre-balling, and balling of single tracks, were also investigated. The obtained results showed that increase of power at a constant speed increase both the track width and depth of penetration but the track height above the substrate is decreased.
- 1 December 2022
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 370, 01003
Open AccessInfluence of selective laser melting process parameters on the characteristics of SiC/Ti6Al4V(ELI) single tracks
Process parameters of selective laser melting, such as track height, track width and depth of penetration, affect the characteristics of laser fused single tracks. The properties of additively manufactured 3D parts depend strongly on the quality of laser melted single tracks and resultant single layers. Layers formed with a good depth of laser penetration provide strong bonding between consecutive layers and the substrate. Poor depth of laser penetration leads to delamination of layers. In this study the effect of the critical process parameters of laser power, laser scanning speed, and laser linear energy density on the characteristics of SiC/Ti6Al4V(ELI) single tracks at different SiC volume fractions (5 %, 10 %, 15 %, 20 %, 25 % and 30%) was investigated. Phenomena, such as the keyhole effect, pre-balling, and balling of single tracks, were also investigated. The obtained results showed that increase of power at a constant speed increase both the track width and depth of penetration but the track height above the substrate is decreased.
- Open Access
- 18 November 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-12
A Theoretical Model of the Flow Properties of Postprocessed Direct Metal Laser Sintering Ti6Al4V (ELI)
Heat treatment of direct metal laser sintering (DMLS) Ti6Al4V (ELI) generates different mechanical properties of the alloy depending on the heat treatment cycle adopted. This is due to the different aspects of the microstructure, such as phase fraction, grain size, texture, and dislocation density, which vary with heat treatment. Other external factors, such as the prevailing level of strain, strain rate, and temperature, also affect the mechanical properties of the material. This paper presents the development of a theoretical model that couples the effects of strain rate, temperature, strain, grain size, and initial dislocation density to describe the flow properties of DMLS Ti6Al4V (ELI). According to the model, higher initial dislocation density results in higher yield stress, low strain hardening, and earlier saturation of flow stress. The model shows that the parabolic shape of the stress-strain curve of the alloy is dictated by the initial dislocation density, which is generally a factor of grain size.
- 18 November 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-12
Open AccessA Theoretical Model of the Flow Properties of Postprocessed Direct Metal Laser Sintering Ti6Al4V (ELI)
Heat treatment of direct metal laser sintering (DMLS) Ti6Al4V (ELI) generates different mechanical properties of the alloy depending on the heat treatment cycle adopted. This is due to the different aspects of the microstructure, such as phase fraction, grain size, texture, and dislocation density, which vary with heat treatment. Other external factors, such as the prevailing level of strain, strain rate, and temperature, also affect the mechanical properties of the material. This paper presents the development of a theoretical model that couples the effects of strain rate, temperature, strain, grain size, and initial dislocation density to describe the flow properties of DMLS Ti6Al4V (ELI). According to the model, higher initial dislocation density results in higher yield stress, low strain hardening, and earlier saturation of flow stress. The model shows that the parabolic shape of the stress-strain curve of the alloy is dictated by the initial dislocation density, which is generally a factor of grain size.