Adewale Oladapo Adegbenjo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Adewale Oladapo Adegbenjo has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Mxolisi Brendon Shongwe
Department of Chemical, Metallurgical and Materials Engineering, Tshwane University of Technology, Pretoria, South Africa
6 shared publications - Peter Apata Olubambi
University of Johannesburg
4 shared publications - Avwerosuoghene Moses Okoro
University of Johannesburg
3 shared publications - Babatunde Abiodun Obadele
Department of Chemical, Materials and Metallurgical Engineering, Botswana International University of Science and Technology, Palapye, Botswana; Department of Chemical and Metallurgical Engineering, Tshwane University of Technology, Pretoria 0001, South Africa
3 shared publications - Mary Ajimegoh Awotunde
Center for NanoEngineering and Tribocorrosion, School of Mining, Metallurgy and Chemical Engineering, University of Johannesburg, Johannesburg, South Africa
3 shared publications Peter Olubambi
3 shared publications
Latest Publications
- Open Access
- 1 January 2023
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 62 (1)
Influence of ultrasonication time on the various properties of alkaline-treated mango seed waste filler reinforced PVA biocomposite
The usage of biodegradable materials is gaining mounting applications owing to the environmental problems created by petroleum-based synthetic materials. Agro-waste materials are finding more scope as reinforcement materials in polymer composites, mainly because of their cost-effectiveness and availability. The main aim of this research work is to utilize agro-waste material in the form of mango seed waste (MSW) as a reinforcing material with polyvinyl alcohol (PVA) to form biocomposite. The biocomposites were fabricated using the solution casting technique. The research work focuses on the influence of varying ultrasonication periods (0–20 min at 5-min intervals, i.e., 0, 5, 10, 15, and 20 min) on the properties of PVA/MSW biocomposites. The fabricated biocomposites were subjected to tensile test, fracture morphology, moisture absorption (MA), Fourier transform infrared spectroscopy, and thermogravimetric analysis. The results revealed that the material with the highest tensile strength was 3.95 MPa obtained with the 20-min ultrasonication sample. This value is 49% higher than that obtained in the sample without ultrasonication. The scanning electron microscopy analysis shows that the 20-min ultrasonication sample indicated a good distribution of MSW fillers in the PVA contrasted with the rest of the samples. The thermal stability of the samples treated with ultrasonication was found to be significantly higher than that of the untreated samples, whereas the MA value decreased with increasing ultrasonication time. It can be observed from the results that biocomposites can be a potential alternative to the synthetic materials used in packaging applications.
- 1 January 2023
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 62 (1)
Open AccessInfluence of ultrasonication time on the various properties of alkaline-treated mango seed waste filler reinforced PVA biocomposite
The usage of biodegradable materials is gaining mounting applications owing to the environmental problems created by petroleum-based synthetic materials. Agro-waste materials are finding more scope as reinforcement materials in polymer composites, mainly because of their cost-effectiveness and availability. The main aim of this research work is to utilize agro-waste material in the form of mango seed waste (MSW) as a reinforcing material with polyvinyl alcohol (PVA) to form biocomposite. The biocomposites were fabricated using the solution casting technique. The research work focuses on the influence of varying ultrasonication periods (0–20 min at 5-min intervals, i.e., 0, 5, 10, 15, and 20 min) on the properties of PVA/MSW biocomposites. The fabricated biocomposites were subjected to tensile test, fracture morphology, moisture absorption (MA), Fourier transform infrared spectroscopy, and thermogravimetric analysis. The results revealed that the material with the highest tensile strength was 3.95 MPa obtained with the 20-min ultrasonication sample. This value is 49% higher than that obtained in the sample without ultrasonication. The scanning electron microscopy analysis shows that the 20-min ultrasonication sample indicated a good distribution of MSW fillers in the PVA contrasted with the rest of the samples. The thermal stability of the samples treated with ultrasonication was found to be significantly higher than that of the untreated samples, whereas the MA value decreased with increasing ultrasonication time. It can be observed from the results that biocomposites can be a potential alternative to the synthetic materials used in packaging applications.
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 615-619
Influence of carbon nanotubes addition on the mechanical properties of nickel aluminide – NiAl
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 615-619
Influence of carbon nanotubes addition on the mechanical properties of nickel aluminide – NiAl
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 625-629
Effects of carbon nanotube weight fraction on the fracture toughness of spark plasma sintered nickel aluminide-NiAl3
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 28, 625-629
Effects of carbon nanotube weight fraction on the fracture toughness of spark plasma sintered nickel aluminide-NiAl3
- 1 September 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 803, 514-526
Interdependence of carbon nanotubes agglomerations, its structural integrity and the mechanical properties of reinforced nickel aluminide composites
- 1 September 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 803, 514-526
Interdependence of carbon nanotubes agglomerations, its structural integrity and the mechanical properties of reinforced nickel aluminide composites
- 24 April 2019
- Published by Springer Nature in JOM
- Vol. 71 (7) , 2262-2271
Interface Analysis of Spark Plasma Sintered Carbon Nanotube Reinforced Ti6Al4V
- 24 April 2019
- Published by Springer Nature in JOM
- Vol. 71 (7) , 2262-2271
Interface Analysis of Spark Plasma Sintered Carbon Nanotube Reinforced Ti6Al4V
- Open Access
- 3 April 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 499 (1) , 012002
Thermal Diffusivity Behaviour of Multi-walled Carbon Nanotube Reinforced Ti6Al4V Metal Matrix Composites
This study investigated the thermal diffusivity behaviours of spark plasma sintered (SPS) multi-walled carbon nanotubes (MWCNTs) reinforced Ti6Al4V composites containing 0, 1, 2 and 3 wt. % of the reinforcement respectively, over a range of 50 – 300 °C. The MWCNTs were dispersed into the Ti6Al4V matrices by high-energy ball milling (HEBM) technique and the milled composite powders were consolidated by SPS under a vacuum atmosphere. The sintering conditions employed were heating rate (100 °C/min), holding time at temperature (5 min), sintering temperature (850 °C) and applied pressure of 50 MPa. The relative densities of the composite discs were measured according to Archimedes' principle while the thermal diffusivities of as-sectioned composite samples were measured using the Laser Flash equipment. Relative densities of the synthesized nanocomposites deteriorated with increase in the weight fraction of MWCNTs added to Ti6Al4V. The thermal diffusivities of the composites containing 1 and 2 wt. % MWCNTs improved with increase in temperature and weight fraction of MWCNTs contents. A reverse trend was observed in the composite containing 3 wt. % MWCNTs, as the measured thermal diffusivities continued to drop with increase in temperature. Although this composite exhibited the best thermal diffusivities compared to the other composites up to 200 °C, a significant drop in thermal diffusivity was recorded between 250 and 300 °C respectively with the values lower than that of the unreinforced Ti6Al4V alloy. However, the thermal diffusivities of MWCNTs/Ti6Al4V composites were generally not dependent on their densification as the composites with higher weight fractions of the reinforcement had higher thermal diffusivities in spite of their lower relative densities.
- 3 April 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 499 (1) , 012002
Open AccessThermal Diffusivity Behaviour of Multi-walled Carbon Nanotube Reinforced Ti6Al4V Metal Matrix Composites
This study investigated the thermal diffusivity behaviours of spark plasma sintered (SPS) multi-walled carbon nanotubes (MWCNTs) reinforced Ti6Al4V composites containing 0, 1, 2 and 3 wt. % of the reinforcement respectively, over a range of 50 – 300 °C. The MWCNTs were dispersed into the Ti6Al4V matrices by high-energy ball milling (HEBM) technique and the milled composite powders were consolidated by SPS under a vacuum atmosphere. The sintering conditions employed were heating rate (100 °C/min), holding time at temperature (5 min), sintering temperature (850 °C) and applied pressure of 50 MPa. The relative densities of the composite discs were measured according to Archimedes' principle while the thermal diffusivities of as-sectioned composite samples were measured using the Laser Flash equipment. Relative densities of the synthesized nanocomposites deteriorated with increase in the weight fraction of MWCNTs added to Ti6Al4V. The thermal diffusivities of the composites containing 1 and 2 wt. % MWCNTs improved with increase in temperature and weight fraction of MWCNTs contents. A reverse trend was observed in the composite containing 3 wt. % MWCNTs, as the measured thermal diffusivities continued to drop with increase in temperature. Although this composite exhibited the best thermal diffusivities compared to the other composites up to 200 °C, a significant drop in thermal diffusivity was recorded between 250 and 300 °C respectively with the values lower than that of the unreinforced Ti6Al4V alloy. However, the thermal diffusivities of MWCNTs/Ti6Al4V composites were generally not dependent on their densification as the composites with higher weight fractions of the reinforcement had higher thermal diffusivities in spite of their lower relative densities.
- Open Access
- 3 April 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 499 (1) , 012010
Thermal Diffusivity Behaviour of Multi-walled Carbon Nanotube Reinforced Ti6Al4V Metal Matrix Composites
This study investigated the thermal diffusivity behaviours of spark plasma sintered (SPS) multi-walled carbon nanotubes (MWCNTs) reinforced Ti6Al4V composites containing 0, 1, 2 and 3 wt. % of the reinforcement respectively, over a range of 50 – 300 °C. The MWCNTs were dispersed into the Ti6Al4V matrices by high-energy ball milling (HEBM) technique and the milled composite powders were consolidated by SPS under a vacuum atmosphere. The sintering conditions employed were heating rate (100 °C/min), holding time at temperature (5 min), sintering temperature (850 °C) and applied pressure of 50 MPa. The relative densities of the composite discs were measured according to Archimedes' principle while the thermal diffusivities of as-sectioned composite samples were measured using the Laser Flash equipment. Relative densities of the synthesized nanocomposites deteriorated with increase in the weight fraction of MWCNTs added to Ti6Al4V. The thermal diffusivities of the composites containing 1 and 2 wt. % MWCNTs improved with increase in temperature and weight fraction of MWCNTs contents. A reverse trend was observed in the composite containing 3 wt. % MWCNTs, as the measured thermal diffusivities continued to drop with increase in temperature. Although this composite exhibited the best thermal diffusivities compared to the other composites up to 200 °C, a significant drop in thermal diffusivity was recorded between 250 and 300 °C respectively with the values lower than that of the unreinforced Ti6Al4V alloy. However, the thermal diffusivities of MWCNTs/Ti6Al4V composites were generally not dependent on their densification as the composites with higher weight fractions of the reinforcement had higher thermal diffusivities in spite of their lower relative densities.
- 3 April 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 499 (1) , 012010
Open AccessThermal Diffusivity Behaviour of Multi-walled Carbon Nanotube Reinforced Ti6Al4V Metal Matrix Composites
This study investigated the thermal diffusivity behaviours of spark plasma sintered (SPS) multi-walled carbon nanotubes (MWCNTs) reinforced Ti6Al4V composites containing 0, 1, 2 and 3 wt. % of the reinforcement respectively, over a range of 50 – 300 °C. The MWCNTs were dispersed into the Ti6Al4V matrices by high-energy ball milling (HEBM) technique and the milled composite powders were consolidated by SPS under a vacuum atmosphere. The sintering conditions employed were heating rate (100 °C/min), holding time at temperature (5 min), sintering temperature (850 °C) and applied pressure of 50 MPa. The relative densities of the composite discs were measured according to Archimedes' principle while the thermal diffusivities of as-sectioned composite samples were measured using the Laser Flash equipment. Relative densities of the synthesized nanocomposites deteriorated with increase in the weight fraction of MWCNTs added to Ti6Al4V. The thermal diffusivities of the composites containing 1 and 2 wt. % MWCNTs improved with increase in temperature and weight fraction of MWCNTs contents. A reverse trend was observed in the composite containing 3 wt. % MWCNTs, as the measured thermal diffusivities continued to drop with increase in temperature. Although this composite exhibited the best thermal diffusivities compared to the other composites up to 200 °C, a significant drop in thermal diffusivity was recorded between 250 and 300 °C respectively with the values lower than that of the unreinforced Ti6Al4V alloy. However, the thermal diffusivities of MWCNTs/Ti6Al4V composites were generally not dependent on their densification as the composites with higher weight fractions of the reinforcement had higher thermal diffusivities in spite of their lower relative densities.
- 1 June 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 749, 818-833
Densification, hardness and tribological characteristics of MWCNTs reinforced Ti6Al4V compacts consolidated by spark plasma sintering
- 1 June 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 749, 818-833
Densification, hardness and tribological characteristics of MWCNTs reinforced Ti6Al4V compacts consolidated by spark plasma sintering
- 27 May 2018
- Published by Springer Nature
- p. 55-61
Improving the Tribological Properties of Ti6Al4V Alloy with Multi-walled Carbon Nanotube Additions
- 27 May 2018
- Published by Springer Nature
- p. 55-61
Improving the Tribological Properties of Ti6Al4V Alloy with Multi-walled Carbon Nanotube Additions
- 30 October 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (12) , 6047-6056
Interfacial Reaction During High Energy Ball Milling Dispersion of Carbon Nanotubes into Ti6Al4V
- 30 October 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (12) , 6047-6056
Interfacial Reaction During High Energy Ball Milling Dispersion of Carbon Nanotubes into Ti6Al4V