MKMehmet Kodal

Mehmet Kodal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mehmet Kodal has a total of 87 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Unraveling the Role of Extrusion Parameters in Bio- and Synthetic-Based Polyamide Fiber Composites

    by Rumeysa Yıldırım, Merve Gökmen, Güralp Özkoç, Olcay Mert, Mehmet Kodal

    In this study, the effects of extrusion process parameters (screw speed, residence time, and fiber feeding protocol) on the morphological, rheological, and mechanical properties of synthetic and bio-based polymeric composites-namely polyamide 6 (PA6)/glass fiber (GF) and polyamide 11 (PA11)/hemp fiber (HF) composites-were comprehensively investigated. For this purpose, scanning electron microscopy (SEM), rheological analyses, tensile, impact, and flexural tests, and average fiber length measurements were performed. The results revealed that late fiber feeding preserved longer fibers in both systems, whereas the effect of screw speed on fiber length depended on the residence time, feeding protocol, and fiber loading, with reductions of up to 14.6% for glass fibers and 28.7% for hemp fibers when the screw speed was increased from 100 to 150 rpm. Rheological analyses showed that the feeding protocol in which the fibers were added to the extruder barrel at the final stage of processing yielded higher complex viscosity, storage modulus, and loss modulus values. On the other hand, a general decrease in the impact strength of the composites was observed with increasing screw speed and residence time. These findings demonstrate that extrusion process parameters play a decisive role in fiber dimensions, matrix-fiber interactions, and the final performance of the composites and highlight the importance of optimizing processing conditions in the production of synthetic and bio-based fiber-reinforced polymeric composites.

  • Open Access

    Preparation and Characterization of PHBV/PLA/TPS Blends Containing Citric Acid-Modified Thermoplastic Starch

    by GülSün Gonca Kandemir, Mehmet Kodal, Serap Mert

    The aim of this study was to modify the structural, mechanical, thermal, rheological, and morphological properties of PHBV-based blends through the incorporation of PLA and citric acid-modified thermoplastic starch (TPS). Although PHBV is a biodegradable polymer with environmental advantages, its processing challenges and relatively low mechanical performance limit its practical applications, which can be addressed by blending it with PLA and TPS to tailor the properties of the resulting materials. TPS was prepared by plasticizing corn starch with glycerol and incorporating different concentrations of citric acid (0, 5, and 10 wt %). Subsequently, PHBV/PLA/TPS blends were obtained by extrusion and characterized by Fourier-transform infrared spectroscopy (FTIR), tensile testing, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), rheological measurements, and scanning electron microscopy (SEM). The results demonstrated that the addition of citric acid altered the morphology, mechanical properties, and thermal behavior of TPS, while its effects on the PHBV/PLA/TPS blends depended strongly on blend composition. Among the TPS formulations, T5 exhibited the highest tensile strength (9.6 MPa), whereas 40PH/30P/30T0 showed the highest tensile strength among the blends (18.7 MPa). The 40PH/40P/20T10 formulation exhibited the most homogeneous morphology and the highest thermal stability among the ternary blends, with a maximum degradation temperature of 295 °C. Overall, the incorporation of PLA and citric acid-modified TPS enabled the properties of PHBV-based blends to be tailored through changes in composition and TPS modification, demonstrating their potential for the development of biodegradable materials with improved and tunable performance.

  • Open Access

    Non-Isothermal Crystallization Behavior and Crystal Morphology of EPDM/PP Thermoplastic Vulcanizates Containing TAC and OV-POSS Coagents

    by Nazlı Yazıcı Çakır, Özgenur İnan Coşkun, Merve Ergün, Mehmet Kodal, Güralp Özkoç

    Ethylene propylene diene monomer rubber/polypropylene (EPDM/PP) thermoplastic vulcanizates containing triallyl cyanurate (TAC) or octavinyl polyhedral oligomeric silsesquioxane (OV-POSS) coagents were prepared by dynamic vulcanization. The effects of coagent type, loading level, and EPDM/PP ratio on non-isothermal crystallization were investigated using differential scanning calorimetry (DSC), polarized optical microscopy (POM), and X-ray diffraction (XRD). Crystallization kinetics were evaluated using the Avrami, Ozawa, and combined Avrami-Ozawa models, while nucleation activity and apparent activation energies were assessed using the Dobreva-Gutzow, Kissinger, Takhor, and Friedman approaches. Both coagents, particularly OV-POSS, shifted crystallization onset toward higher temperatures, demonstrating enhanced heterogeneous nucleation. The decreasing Avrami-derived half-times t0.5 with increasing cooling rate were qualitatively consistent with the experimental DSC half-times t1/2. The Ozawa model did not adequately describe the investigated systems, while the combined Avrami-Ozawa model provided satisfactory correlations. The influence of the coagents on the overall crystallization rate depended on composition, loading, and cooling rate. In particular, high OV-POSS loading promoted earlier nucleation but did not consistently shorten t0.5, especially in the EPDM-rich TPVs. POM revealed earlier crystal formation, increased nucleation density, and smaller spherulites in the coagent-containing samples. DSC analysis revealed an increase in PP-normalized crystallinity upon OV-POSS incorporation, while XRD confirmed an increased crystalline fraction, predominantly associated with the α-crystalline form. This effect was particularly pronounced in the PP-rich formulations. Although OV-POSS promoted heterogeneous nucleation and crystalline structure development, its influence on the overall crystallization rate remained dependent on blend composition, coagent loading, and cooling conditions, suggesting a complex interplay between nucleation and subsequent crystal growth.

  • Open Access

    Investigating the Crystallization Kinetics and Mechanical Properties of Poly(Butylene Succinate): The Dual Role of Polyoxymethylene Blending and MWCNT Heterogeneous Nucleation

    by Cansın Tutuş, Rumeysa Yıldırım, Nazlı Yazıcı Çakır, Merve Gökmen, Güralp Özkoç, Mehmet Kodal

    This study investigates the crystallization behavior of poly(butylene succinate) (PBS) through blending with highly crystalline polyoxymethylene (POM) to address the inherently slow crystallization rate of PBS. The non-isothermal crystallization kinetics of the individual constituents within the blend systems were systematically investigated to elucidate their crystallization behavior under cooling conditions. In addition, the influence of multi-walled carbon nanotube (MWCNT) incorporation on the mechanical, thermomechanical, and morphological properties of PBS/POM blends was evaluated. The crystallization behavior was analyzed using kinetic approaches under non-isothermal conditions. Spherulite morphology was observed via polarized optical microscopy equipped with a controlled heating–cooling stage to elucidate spherulitic development. Scanning electron microscopy (SEM) revealed no obvious micron-scale phase separation in the PBS/POM blends, while the distinct crystallization behavior of the PBS and POM phases observed by differential scanning calorimetry (DSC) indicated that the two components retained their individual crystalline phases, supporting the partial miscibility of the blends. In the ternary systems, SEM observations showed a relatively uniform distribution of MWCNTs at the spatial scale accessible by SEM, with no pronounced micron-scale agglomerates readily discernible within the examined regions. Mechanical analyses demonstrated that the incorporation of MWCNTs enhanced the properties of the blends, particularly the elastic modulus and tensile strength. Kinetic analysis further indicated that MWCNTs influenced the crystallization behavior of the PBS and POM phases through nucleation effects, with their influence depending on the PBS/POM blend composition.

  • Open Access

    High Melt Strength Polypropylene via Reactive Extrusion for Injection-Molded Foams: Performance of Virgin and Recycled Blends

    by Mert Emre Öztoksoy, Ramazan Bedirhan Yıldız, Rumeysa Yıldırım, Mehmet Ali Oral, Güralp Özkoç, Mehmet Kodal

    This research demonstrates an eco-friendly and reproducible method to synthesize high melt strength polypropylene (HMSPP) by reactive extrusion of virgin polypropylene (PP) and recycled polypropylene (rPP) blends with low-density polyethylene (LDPE). In contrast to many previous reactive extrusion studies that primarily focused on low-MFR polypropylene grades for extrusion or thermoforming-based processes, the present study targets high-MFR-HMSPP materials suitable for injection molding applications, particularly injection-molded foams. A peroxide initiator (DHBP) and a polyfunctional coagent, namely trimethylolpropane triacrylate (TMPTA), were added to the blends to induce long-chain branching (LCB) while maintaining adequate processability. Detailed analyses were conducted to evaluate the effects of LDPE (20–40 wt %) and TMPTA (2–5 wt %) on morphology, thermal behavior, rheological response, mechanical performance, and foaming characteristics. Rheological investigations revealed pronounced increases in complex viscosity, storage modulus, and melt elasticity, accompanied by strain-hardening behavior in TMPTA-modified blends, which are widely accepted rheological signatures of long-chain branching rather than extensive gel formation. SEM analyses demonstrated improved interfacial compatibility among reactively modified blends and refined LDPE domain structures following reactive modification. The recycled blend (rPP5) displayed similar foamability, indicating the potential capability of the procedure to upcycle waste PP.

  • Open Access

    PLA/Collagen/Hydroxyapatite Ternary Biocomposites for Biodegradable Bone Screw Applications

    by Ayşegül Uzuner-Demir, Rumeysa Yıldırım, Hürol Koçoğlu, Mihriban Aydoğan-Gemici, Zehra Betül Ahi, Fatih Arıcan, Olcay Mert, Güralp Özkoç, Mehmet Kodal

    Poly(lactic acid) (PLA)-based biocomposites incorporating collagen (COLL) and hydroxyapatite (HA) were produced via melt micro-compounding and subsequent injection molding. 1,4-phenylene diisocyanate (PDI) was employed as a compatibilizer, while poly(ethylene glycol) (PEG) was used as a plasticizer. The morphological, thermal, rheological, and mechanical properties, as well as surface wettability, degradation behavior, and cytotoxicity, were comprehensively evaluated. SEM and DSC analyses revealed the phase distribution and thermal transitions, while rheological measurements showed that PEG reduced melt viscosity by increasing chain mobility. Mechanical performance was evaluated using tensile, impact, and DMA tests on standard specimens, indicating that HA primarily enhanced stiffness (elastic modulus), whereas PEG improved toughness, resulting in higher impact strength. Biodegradable bone screw prototypes were produced with the same formulations and subjected to torsion, enzymatic degradation, and MTT cytotoxicity tests. Degradation results indicated that biocomposites containing PEG, collagen, and HA exhibited accelerated mass loss. Overall, the 70/20/10 PLA/COLL/HA/PEG/PDI formulation was more suitable for soft (trabecular) bone tissue, while the 70/10/20 PLA/COLL/HA/PDI formulation showed advantages for hard (cortical) bone tissue applications.

  • Production of Collagen Modified PDLA Biofilms

    by Ayşegül Uzuner‐Demir, Mihriban Aydoğan‐Gemici, Oğuzhan Polat, Zehra Betül Ahi, Fatih Arıcan, Güralp Özkoç, Olcay Mert, Mehmet Kodal

    Enhancing the biological functionality of polymeric biomaterials, particularly cell adhesion, proliferation, and biocompatibility, is essential for developing functional applications in tissue engineering. In this work, poly(D‐lactic acid) (PDLA) was covalently grafted with collagen (PDLA‐ g ‐Coll) to overcome PDLA's inherent limitations in cellular interactions. The hybrid films were fabricated via solvent casting and subjected to comprehensive biological evaluation. In vitro experiments using L929 mouse fibroblast cells, demonstrated a marked enhancement in cell attachment and proliferation on the PDLA‐ g ‐Coll films compared to unmodified PDLA and pure collagen controls, as confirmed by MTT assays. These improvements are attributed to the increased surface hydrophilicity conferred by the grafted collagen chains, a finding corroborated by contact angle measurements. The favorable surface morphology of the PDLA‐ g ‐Coll films further supported cell proliferation. Collectively, these results highlight the synergistic integration of PDLA's mechanical strength and biodegradability with collagen's bioactivity, yielding a composite material with significant potential for application in tissue engineering.

  • Open Access

    From Plant to Polymers: Micro-Processing Sisal Fiber-Reinforced PLA/PHA Bio-LFTs at Laboratory Scale

    by Rumeysa Yıldırım, Nursel Karakaya, Bas Liebau, Tim Welten, Beyza Bayram, Mehmet Kodal, Güralp Özkoç

    This study explores the development of long fiber-reinforced thermoplastic (LFT) composites based on blends of poly(lactic acid) (PLA) and polyhydroxyalkanoate (PHA), reinforced with sisal fibers. A novel lab-scale LFT line was employed to fabricate the long fiber composites, effectively addressing the challenges associated with dispersing and processing high-aspect-ratio natural fibers. The rheological, mechanical, thermal, and morphological properties of the resulting bio-LFT composites were systematically characterized using FTIR, SEM, rotational rheology, mechanical testing, DSC, and TGA. The results demonstrated generally homogeneous fiber dispersion, although limited interfacial adhesion between the fibers and polymer matrix was observed. Mechanical tests revealed that sisal fiber incorporation significantly enhanced tensile strength and stiffness, while impact toughness decreased. Thermal analyses showed improved crystallinity and thermal stability with increasing PHA content and fiber reinforcement. Overall, this work highlights the potential of natural fibers to create high-performance, sustainable biocomposites and lays a solid foundation for future advancements in developing eco-friendly structural materials.


  • Enhanced Crystallinity Through Melt Annealing of Thermoplastic Polyurethanes

    by Bahar Durak Akkoyun, Abdulmounem Alchekh Wis, Rumeysa Yıldırım, Ümit Makal, Güralp Özkoç, Mehmet Kodal

    This study evaluated the influence of melt annealing on thermoplastic polyurethane (TPU) synthesized via reactive extrusion, aiming to enhance TPU melt crystallization behavior. The melt annealing process involved reprocessing the polymer in a twin‐screw extruder, leveraging a novel approach to manipulating crystallization behavior by optimizing melt annealing conditions to activate microphase separation. Differential scanning calorimetry analysis indicated increased nucleation density and a shift in peak crystallization temperature to higher values during cooling. Phase morphology was examined using scanning electron microscopy, while gel permeation chromatography was utilized to assess molecular weight changes. X‐ray diffraction provided insights into TPU microstructural modifications, and mechanical properties were evaluated via tensile tests. Fourier‐transform infrared spectroscopy was employed to analyze annealing‐induced changes in the hard segment structure and interpolymer bonding. The findings demonstrated that annealing enhances mechanical properties, promotes microphase separation, and increases the energy available for movement and realignment of hard segments, thereby improving TPU's thermal stability. Precise control of annealing temperature was critical to prevent adverse effects on polymer morphology or molecular weight reduction. Annealing at 210°C yielded the highest degree of crystallinity, optimizing mechanical properties and thermal stability.


  • Lab‐scale manufacturing of thermoplastic matrix‐continuous carbon fiber filaments for additive manufacturing: Melt impregnation, properties of the filaments and its printed composites

    by Yunus Alp Sütcüler, Guy J. P. Bex, Cesar A. Stupp, Mehmet Kodal, A. Tessa Ten Cate, Güralp Özkoç

    Additive manufacturing encounters significant barriers to its broader application in large‐scale production. This research seeks to mitigate critical limitations, including a trade‐off between impregnation speed and quality in filament preparation and inconsistent fiber distribution in continuous carbon filaments (CCFs), mainly attributed to the rounding process of unidirectional tapes and insufficient interlayer adhesion. A novel lab‐scale impregnation line was engineered to address these challenges, facilitating the production of CCFs using three distinct types of carbon fiber in conjunction with recycled glycol‐modified poly(ethylene terephthalate) (rPETG) resin. This new lab‐scale process produces uniform fiber distribution within PETG matrix and prevents S‐shaped distortions typically observed in conventionally rounded tapes. The type of carbon fiber sizing influences the impregnation process and tensile strength of the CCFs. Specifically, CCFs with flexible sizing demonstrated a 15% reduction in tensile strength due to fuzz formation during impregnation. These CCFs were subsequently employed in 3D printing applications, with the fabricated composite components subjected to interlaminar shear strength (ILSS) testing. The study concludes that recycled PETG is a viable additive manufacturing material when combined with appropriately sized carbon fibers. Additionally, it highlights the advantages of omitting the rounding stage, which enhances the quality of CCF and optimizes production efficiency.Highlights: A lab‐scale direct melt impregnation system was designed in this study. The impact of different sizing types on carbon fibers was investigated. 3D‐printed continuous fiber filaments were prepared. New lab‐scale process produces uniform fiber distribution within PETG matrix. S‐shaped distortions observed in conventionally rounded tapes were prevented.