RSRahul Singh

Rahul Singh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Rahul Singh has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Millimeter-Wave Receiver Using a Wideband Low-Noise Amplifier With One-Port Coupled Resonator Loads

    by Rahul Singh, Susnata Mondal, Jeyanandh Paramesh

    This article presents design techniques to facilitate the use of the driving point impedance (Z₁₁) of one-port transformer-coupled resonators as wideband loads of millimeter-wave amplifier stages for a 28-GHz receiver front end. While the use of both the Z₁₁ of a one-port and the transimpedance (Z₂₁) of a two-port coupled resonator is considered to achieve a wideband response, it is shown that under conditions of low magnetic coupling and constrained network quality factor, the use of Z₁₁ can result in a higher gain-bandwidth product of low-noise amplifier (LNA) amplifier stages. The effect of the complex zero in the Z₁₁ response on the in-band gain ripple is shown to be alleviated merely by lowering the quality factor of the transformer's secondary coil; this strongly motivates the use of compact, nested-inductor transformer layouts. Implemented in a 65-nm CMOS process, a three-stage LNA (with Z₁₁ wideband loads in two stages) achieves a 24.4-32.3-GHz bandwidth (27.9 % fractional bandwidth), a peak S₂₁ of 24.4 dB (20.4 dB), a minimum noise figure (NF) of 4 dB (4.6 dB), and an input-referred P1dB of -23 dBm (-22 dBm) while consuming 22-mW (9.9 mW) power from a 1.1-V (0.85 V) supply. The use of compact transformers limits the LNA's footprint to only 0.12 mm². A 26.5-32.5-GHz quadrature receiver prototype employing the LNA achieves a 29.5-dB peak conversion gain, a 5.3-dB minimum NF, and a -26-dBm input-referred P1dB while consuming 33 mW from a 1.1-V supply.


  • A Compact Digitally-Assisted Merged LNA Vector Modulator Using Coupled Resonators for Integrated Beamforming Transceivers

    by Rahul Singh, Susnata Mondal, Jeyanandh Paramesh

    This paper presents a compact differential quadrature generation scheme using transformer coupled resonators for use in scalable fifth-generation (5G) phased-array architectures. A merged low-noise amplifier vector modulator (LNA-VM) architecture is introduced where quadrature generation, conventionally implemented using an explicit quadrature hybrid, is now seamlessly integrated with the load of an LNA gain stage facilitating a compact design. The outputs of a lowQ coupled-resonator load in the LNA is used for quadrature generation, and Cartesian combining is implemented by phase-invariant programmable gain amplifiers (PGAs) with constant input capacitance and output conductance across phase settings-this ensures low rms gain and phase errors. A 25.1-27.6-GHz phased array channel employing the proposed scheme is implemented in 65-nm CMOS. The merged LNA-VM is digitally tunable across 2.5 GHz (25.1-27.6 GHz) and achieves rms gain and phase errors (measured at band edges) better than 0.42 dB (0.64 dB) and 4.5° (6.9°), respectively, for a bandwidth of 500 MHz (700 MHz). It occupies a composite area of only 0.123 mm 2 while consuming 30.5 mW from a 1-V supply. To achieve quadrature locking at the desired frequency within the LNA-VM's tuning range, an on-chip mixer-based quadrature error detection and calibration scheme is presented. The proposed scheme is demonstrated to be robust in the face of gain and layout-induced mismatches which can be significant at millimeter-wave (mm-wave) frequencies.


  • Top Cited Papers

    A 25–30 GHz Fully-Connected Hybrid Beamforming Receiver for MIMO Communication

    by Susnata Mondal, Rahul Singh, Ahmed I. Hussein, Jeyanandh Paramesh

    This paper presents a ``fully-connected'' hybrid beamforming receiver that independently weights each element in an antenna array prior to separate downconversion chains that output independent baseband streams. A receiver architecture is introduced, which implements RF-domain complex-valued Cartesian weighting, RF-domain combining, and multi-stream heterodyne complex-quadrature downconversion. Each RF-domain Cartesian weight is implemented by a pair of 5-bit digitally controlled programmable-gain amplifiers, whose outputs are combined with the weighted signals from other antennas prior to complex-quadrature downconversion. Signal combination is performed by a wideband small-footprint distributed active combiner. A 25-30 GHz hybrid beamforming receiver with eight antenna inputs and two baseband output streams is designed in 65-nm CMOS. In each antenna path, the receiver achieves 34-dB conversion gain, 7.3-dB minimum noise figure, and 5 GHz of RF bandwidth. The entire receiver consumes 340 mW (equivalent to 27.5 mW per antenna per stream) including low-noise amplification, RF-domain beamforming, multi-stream downconversion, and local oscillator generation and distribution circuitry. The receiver occupies 3.86 mm² excluding pads, equivalent to 0.36 mm² per antenna per stream. Single-element characterization results are presented, along with characterization of several spatial processing techniques including interference cancellation (20 dB peak to null for two elements), simultaneous two-stream reception, and adaptive-codebook-search-based beam acquisition.


  • Design Criteria in Sizing Phase-Change RF Switches

    by Gregory Slovin, Min Xu, Rahul Singh, T. E. Schlesinger, Jeyanandh Paramesh, James A. Bain

    This paper presents design criteria for four-terminal phase-change (PC) RF switches as a function of their dimensions, (heater width, RF gap, and barrier thickness), materials, and connection topology. Reducing heater width is shown to reduce switch actuation power, with this reduction ultimately being limited by the maximum allowed heater current density, as set by projected reliability. Narrower RF gaps are shown to increase switch cut-off frequency FCO, because they decrease on-state resistance more than they increase off-state capacitance. The balance of this increased FCO versus the estimated reduction in power handling as the RF gap shrinks is quantified. Barrier layers of AlN thicker than 200 nm are shown to be sufficient to electrically decouple the switch from the heater trace. Coupling to heater pads can also be significant unless pad sizes are reduced as in a monolithically integrated switch. Finally, it is demonstrated that division of the switch into multiple parallel segments is a viable approach for lowering the heater actuation voltage for CMOS integration. A 12.5% increase in COFF (~1.5 fF) was observed and 35% increase in actuation power at temperature was needed in a two-segment parallel switch, as compared to a single segment switch.


  • Open Access

    A Reconfigurable Dual-Frequency Narrowband CMOS LNA Using Phase-Change RF Switches

    by Rahul Singh, Gregory Slovin, Min Xu, T. E. Schlesinger, James A. Bain, Jeyanandh Paramesh

    This paper presents a dual-band low-noise amplifier (LNA) that can be reversibly configured between 3 and 5 GHz using a phase-change (PC) RF switch. Simultaneous noise and conjugate input matching is achieved at the two frequencies using a single PC RF switch and coupled source inductors, thereby minimizing integration complexity and enabling a compact design roughly equal in size to a single-band design. The PC switch has extremely low on-state resistance (1.5-4Ω) and parasitic capacitance (12-16 fF), and has a compact footprint (~50 μm 2 ). A chip containing the PC switch is fabricated in-house while the rest of the LNA is fabricated in a 0.13-μm CMOS technology. The two chips are combined using an in-house flip-chip integration process. Characterization from five prototypes fabricated in two batches is presented. The integrated LNAs achieved peak gain greater than 20 dB and minimum noise figure less than 2.9 dB in both the frequency bands while consuming a peak power of 7.2 mW from a 1.2-V supply. Comparison of the CMOS-PC prototypes with carefully designed control LNAs demonstrates the effectiveness of the PC switch for RF reconfiguration, which allows the reconfigurable LNA to achieve performance comparable to its nonreconfigurable counterparts.