SMSusnata Mondal

Susnata Mondal

*This is an algorithmically generated author record based on publicly available information.

Susnata Mondal has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Design Techniques for 48/56 Gb/s/Lane UCIe-S D2D and 45 Gb/s/Lane UCIe-Like Off-Package Links

    by Susnata Mondal, Sashank Krishnamurthy, Shuhei Yamada, Zhaokai Liu, Junyi Qiu, Soumya Bose, Zuoguo Wu, Gerald Pasdast, James Jaussi, Mozhgan Mansuri

  • A 108 Gb/s PAM-4 VCSEL-Based Direct-Drive Optical Engine for Co-Packaged Optics Applications

    by Susnata Mondal, Sashank Krishnamurthy, Junyi Qiu, Tolga Acikalin, Soumya Bose, Shuhei Yamada, James Jaussi, Mozhgan Mansuri

    This article presents a multimode vertical-cavity surface-emitting laser (VCSEL)-based direct-drive optical engine for co-packaged optics (CPOs) applications that employs pulse amplitude modulation (PAM)-4 to enhance shoreline bandwidth (BW) density and features a compact direct optical wiring (DOW) approach for on-package fiber termination. On the transmit side, a VCSEL driver (VCDRV) comprising a passive complementary-drive complex-zero continuous-time linear equalizer (CZ-CTLE) is introduced to compensate for the VCSEL’s complex-pole response while offering the high linearity required for PAM-4 signaling. The receiver integrates a high-linearity transimpedance amplifier front-end (TIA-FE) capable of handling large input current swings, followed by an active CZ-CTLE to equalize the complex-pole pair response of the low-gain shunt-feedback transimpedance amplifier (TIA). The transceiver prototype, fabricated in a 22-nm FinFET process and integrated on-package with optical devices and fiber-termination, achieves a PAM-4 data rate of 108 Gb/s with a record energy efficiency (EE) of 0.9 pJ/b—representing over $1.7\times $ improvement in data rate compared to previously reported VCSEL-based transceivers. The optical transmitter supports 128 Gb/s PAM-4 operation, demonstrating a $1.5\times $ data rate improvement and $1.6\times $ better EE than the fastest reported integrated VCDRV. Compared to PAM-4 VCDRVs in the prior art, this work achieves $2\times $ higher data rate, $\gt 1.8\times $ better optical modulation amplitude (OMA), and $3\times $ better EE.


  • A 4 × 50 Gb/s 2.9-pJ/b NRZ VCSEL-Based Co-Packaged Optical Link With Fiber Termination

    by Sashank Krishnamurthy, Susnata Mondal, Junyi Qiu, Joseph Kennedy, Soumya Bose, Tolga Acikalin, Shuhei Yamada, James Jaussi, Mozhgan Mansuri

    A four-channel vertical cavity surface-emitting laser (VCSEL)-based co-packaged optical (CPO) transceiver (TRX) is demonstrated, integrating a photodiode (PD) array, a trans-impedance amplifier front-end integrated circuit (TIA-FE IC), an electrical receiver (RX) IC, and optical fiber termination on a single package on the receive side. The transmitter (TX) counterpart incorporates a VCSEL array, a VCSEL driver IC, and an electrical TX IC, all on a single package. To mitigate the group delay (GD) distortion caused by packaging parasitics, an input matching network is introduced in the TIA-FE IC. Several bandwidth extension techniques are employed, along with a two-tap Cherry–Hooper-based FIR feedforward equalizer (FFE) in the electrical RX IC, to compensate for inter-symbol interference (ISI) and a low-noise double-tail latch. When modulated by its VCSEL-based optical TX counterpart, the RX achieves an aggregate four-channel data rate of 200 Gb/s non-return-to-zero (NRZ) at 1.5 pJ/b, with a bit error rate of less than $10^{-12}$ and a sensitivity of −6 dBm.


  • A 4-Ch × 64 Gb/s/Ch NRZ VCSEL-Based Co-Packaged Fiber-Terminated Optical TX and 80-Gb/s Optical Driver

    by Susnata Mondal, Junyi Qiu, Sashank Krishnamurthy, Joseph Kennedy, Soumya Bose, Tolga Acikalin, Shuhei Yamada, James Jaussi, Mozhgan Mansuri

    This article introduces a four-channel (4-Ch) multi-mode (MM) vertical-cavity surface-emitting laser (VCSEL)-based co-packaged optical transmitter (TX), integrating a VCSEL array, a VCSEL driver (VCDRV) IC, an electrical TX IC, and optical fiber termination within a single package. A complex-zero continuous-time linear equalizer (CZ-CTLE) is proposed to effectively equalize the complex-pole response of the VCSEL, improving in-band gain/group delay (GD) flatness and extending bandwidth (BW). To enhance link energy efficiency and jitter margin, resonant clocking techniques are proposed, including a transmission-line-based resonant global clock distribution and a wide-tuning-range coupled-resonator-based quadrature generation. A low-power electrical TX architecture employing an NMOS-over-NMOS (N/N) voltage-mode driver with eye symmetry correction is introduced to further improve the energy efficiency and link margin. The optical TX prototype, implemented in a 22-nm FinFET process, achieves an aggregate non-return-to-zero (NRZ) data rate of 256 Gb/s with an energy efficiency of 1.3 pJ/b. This work outperforms previous optical TXs by $\gt 2.2\times $ in optical modulation amplitude, achieving $1.4\times $ ( $7.6\times $ ) greater eye width (EW) [eye height (EH)], with 14% higher per-channel baud rate and 11% better energy efficiency. The direct-drive optical driver achieves 80-Gb/s NRZ operation, demonstrating a 13% higher data rate and $25\times $ better energy efficiency than prior art. This work also marks the first successful demonstration of more than 50-Gb/s VCSEL-based co-packaged optical TX topology at a $6.4\times $ higher rate than the previous efforts.


  • Open Access

    Dual-Band, Two-Layer Millimeter-Wave Transceiver for Hybrid MIMO Systems

    by Susnata Mondal, Larry Richard Carley, Jeyanandh Paramesh

    This article presents a two-layer low-complexity fully connected (FC) RF/analog weighting multi-input–multi-output (MIMO) transceiver comprising an RF weight layer and an analog–baseband weight layer. The transceiver can serve as a small-scale MIMO system by itself and can serve as the building block in a larger hybrid MIMO system. The architecture mitigates the complexity versus spectral-efficiency tradeoffs of existing MIMO architectures and enables MIMO stream/user scalability, superior energy efficiency, and spatial-processing flexibility. A compact, reconfigurable bidirectional circuit architecture is introduced, including a new Cartesian-combining/splitting beamforming receiver/transmitter, dual-band bidirectional beamforming network, dual-band frequency translation chains, and baseband Cartesian beamforming with an improved programmable gain amplifier design. A 28-/37-GHz band, two-layer, eight-element, four-stream hybrid MIMO transceiver prototype is designed in 65-nm CMOS to demonstrate the above features. The prototype achieves accurate beam/null-steering capability, excellent area/power efficiency, and state-of-the-art TX/RX mode performance in two simultaneous bands while demonstrating multi-antenna (up to eight) multi-stream (up to four) over-the-air spatial multiplexing operation using the proposed energy-efficient two-layer hybrid beamforming scheme.


  • Power-Efficient Design Techniques for mm-Wave Hybrid/Digital FDD/Full-Duplex MIMO Transceivers

    by Susnata Mondal, Jeyanandh Paramesh

    This article describes system and circuit design techniques to enhance power efficiency and incorporate new features in millimeter-wave multi-input-multi-output (MIMO) transceivers. The higher peak-to-average power ratio (PAPR) of the signal transmitted from a digital beamformer (DBF) or a fully connected hybrid beamforming (FC-HBF) transmitter compared with the conventional partially connected hybrid beamforming (PC-HBF) transmitter is identified for the first time. It is then shown that when a power amplifier (PA) with better back-off efficiency than Class-A PA is used, the overall power efficiency of the FC-HBF is superior to the PC-HBF for a given antenna geometry. Second, a new mechanism for built-in dual-band, per-element self-interference cancellation (SIC) is introduced to enable multi-antenna frequency-division-duplex (FDD) and full-duplex (FD) operation. Such SIC can only be supported in the proposed FC-HBF architecture. Several innovative circuit concepts are introduced, including low-loss wideband antenna interface design, dual-band power combining PA, dual-band RF-SIC design, and bidirectional MIMO signal path design. To demonstrate these techniques, a 28-/37-/39-GHz bidirectional two-stream front-end single-element prototype is designed in the 65-nm CMOS. The prototype can be configured as a transmit (TX) or receive (RX) element in DBFs or FC-HBFs which can in turn be configured to support TDD, FDD, or FD operation. The front-end achieves 16-/11-dB RX gain, 6.2-/7-dB NF, 15.8-/16.8-dBm saturated PA output power, and 20%/21.6% peak PA efficiency in the 28-/37-GHz bands. Extensive characterization results are presented to compare the energy efficiencies of the PC-HBF and FC-HBF architectures. The prototype is also characterized in the FDD/FD mode and achieves 36-dB peak RF-domain SIC and better than 26-dB RF-domain SIC across 0.5-GHz modulation bandwidth.


  • A Millimeter-Wave Receiver Using a Wideband Low-Noise Amplifier With One-Port Coupled Resonator Loads

    by Rahul Singh, Susnata Mondal, Jeyanandh Paramesh

    This article presents design techniques to facilitate the use of the driving point impedance (Z₁₁) of one-port transformer-coupled resonators as wideband loads of millimeter-wave amplifier stages for a 28-GHz receiver front end. While the use of both the Z₁₁ of a one-port and the transimpedance (Z₂₁) of a two-port coupled resonator is considered to achieve a wideband response, it is shown that under conditions of low magnetic coupling and constrained network quality factor, the use of Z₁₁ can result in a higher gain-bandwidth product of low-noise amplifier (LNA) amplifier stages. The effect of the complex zero in the Z₁₁ response on the in-band gain ripple is shown to be alleviated merely by lowering the quality factor of the transformer's secondary coil; this strongly motivates the use of compact, nested-inductor transformer layouts. Implemented in a 65-nm CMOS process, a three-stage LNA (with Z₁₁ wideband loads in two stages) achieves a 24.4-32.3-GHz bandwidth (27.9 % fractional bandwidth), a peak S₂₁ of 24.4 dB (20.4 dB), a minimum noise figure (NF) of 4 dB (4.6 dB), and an input-referred P1dB of -23 dBm (-22 dBm) while consuming 22-mW (9.9 mW) power from a 1.1-V (0.85 V) supply. The use of compact transformers limits the LNA's footprint to only 0.12 mm². A 26.5-32.5-GHz quadrature receiver prototype employing the LNA achieves a 29.5-dB peak conversion gain, a 5.3-dB minimum NF, and a -26-dBm input-referred P1dB while consuming 33 mW from a 1.1-V supply.


  • A Compact Digitally-Assisted Merged LNA Vector Modulator Using Coupled Resonators for Integrated Beamforming Transceivers

    by Rahul Singh, Susnata Mondal, Jeyanandh Paramesh

    This paper presents a compact differential quadrature generation scheme using transformer coupled resonators for use in scalable fifth-generation (5G) phased-array architectures. A merged low-noise amplifier vector modulator (LNA-VM) architecture is introduced where quadrature generation, conventionally implemented using an explicit quadrature hybrid, is now seamlessly integrated with the load of an LNA gain stage facilitating a compact design. The outputs of a lowQ coupled-resonator load in the LNA is used for quadrature generation, and Cartesian combining is implemented by phase-invariant programmable gain amplifiers (PGAs) with constant input capacitance and output conductance across phase settings-this ensures low rms gain and phase errors. A 25.1-27.6-GHz phased array channel employing the proposed scheme is implemented in 65-nm CMOS. The merged LNA-VM is digitally tunable across 2.5 GHz (25.1-27.6 GHz) and achieves rms gain and phase errors (measured at band edges) better than 0.42 dB (0.64 dB) and 4.5° (6.9°), respectively, for a bandwidth of 500 MHz (700 MHz). It occupies a composite area of only 0.123 mm 2 while consuming 30.5 mW from a 1-V supply. To achieve quadrature locking at the desired frequency within the LNA-VM's tuning range, an on-chip mixer-based quadrature error detection and calibration scheme is presented. The proposed scheme is demonstrated to be robust in the face of gain and layout-induced mismatches which can be significant at millimeter-wave (mm-wave) frequencies.


  • 21.3 A Reconfigurable Bidirectional 28/37/39GHz Front-End Supporting MIMO-TDD, Carrier Aggregation TDD and FDD/Full-Duplex with Self-Interference Cancellation in Digital and Fully Connected Hybrid Beamformers

    by Susnata Mondal, Rahul Singh, Jeyanandh Paramesh

    This paper presents a 28/37/39GHz front-end applicable to beyond-5G wireless networks. It features three key contributions. First, a fully connected (FC) transmitter architecture is introduced for hybrid beamforming (HBF); it is shown that the power efficiency of FC-HBF is superior to the conventional partially connected (PC) HBF for a given modulation and antenna geometry. Second, a compact/low-cost circuit concept is introduced that supports bi-directional T/R operation concurrently at 28 and 37/39GHz, thereby facilitating multi-antenna carrier-aggregation (CA) or MIMO TDD with high antenna count. Third, a built-in mechanism for dual-band, per antenna, self-interference cancellation (SIC) is introduced, thanks to the FC-HBF architecture. The front-end is applicable to FDD or full-duplex (FD) multi-antenna systems; such SIC is not available in PC-HBF's. Also, the front-end is directly applicable to dual-band digital beamformers (DBF).


  • A Reconfigurable 28-/37-GHz MMSE-Adaptive Hybrid-Beamforming Receiver for Carrier Aggregation and Multi-Standard MIMO Communication

    by Susnata Mondal, Jeyanandh Paramesh

    This paper presents a multi-standard fully connected hybrid beamforming (FC-HBF) receiver that can be reconfigured between two fully connected two-stream multi-input-multi-output (MIMO) modes at 28- or 37-GHz band, and an inter-band carrier-aggregation (CA) mode enabling concurrent single-stream operation at 28 and 37 GHz. A new image-reject (IR) heterodyne beamforming architecture is introduced that facilitates easy reconfiguration. Concurrent dual-band operation of the beamformer front end is achieved by using an inherently wideband Cartesian-combining-based RF-domain complex-weighting architecture, which is implemented using coupled-resonator-based dual-band gain stages, and current-mode dual-band active combiners. The downconversion stage comprises a cascade of complex-quadrature mixing stages that combines Cartesian complex-weighting operation with image rejection. A new quadrature error detection and calibration scheme is also introduced to improve the image rejection of the proposed architecture. A minimum mean-square error (MMSE) beam adaptation technique, introduced for the first time in an RF or hybrid beamformer, breaks the need for individual access to the beamformer inputs needed in a traditional least-mean-square (LMS) scheme and allows both main lobe and null adaptation. A 28-/37-GHz hybrid beamforming receiver with four antenna inputs and two baseband output streams is designed in 65-nm CMOS that demonstrates the above features. In each antenna path, the receiver achieves 33-dB (26.5 dB) peak conversion gain, 2.75-GHz (3.75 GHz) RF bandwidth, and 5.7-dB (8.5 dB) NF at 28 GHz (37 GHz). The entire receiver consumes 310 mW and occupies 2.2 mm 2 core area. Extensive characterization results for single-element and several multi-element scenarios are presented including concurrent dual-band receiving (>35-dB image rejection), null-steering (>25-dB peak to null for two elements), and multi-element CA (~50-dB inter-carrier interference rejection).