Thulasi Vijayakumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thulasi Vijayakumar has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
C. Kannan
1 shared publication- Chidambaram Kannan
School of Mechanical Engineering, Vellore Institute of Technology, Vellore, Tamil Nadu, India
1 shared publication Hirak Jyoti Gayen
A R A I
1 shared publicationK. S. V. Krishna Reddy
School of Mechanical and Building Science, VIT University, Vellore, Tamil Nadu 632014, India
1 shared publicationKarrupa Raj Rajagopal Thundil
1 shared publication- Kasianantham Nanthagopal
School of Mechanical Engineering, Vellore Institute of Technology, Vellore, India
1 shared publication
Latest Publications
- Open Access
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
Numerical Study of the Effect of Hybrid Nanofluid Volume Fractions on the Thermal Hydraulic Efficiency of a Concentric Double Pipe Heat Exchanger
A key problem in sustainable thermal system design is to improve the efficiency of heat transfer. The application of nanofluids, especially the hybrid nanofluids has become a promising method of enhancing the performance of heat exchangers because of their great thermophysical characteristics. This paper has presented a numerical analysis to determine the rate of heat transfer, the overall heat transfer coefficient, and pressure drop of four hybrid nanofluids namely CNT-SiC/water, MgO-Fe3O4/water, Al2O3-TiO2/water and CuO-SiO2/water in the counter-flow concentric pipe heat exchanger in turbulent flow regime. The simulations were carried out with Reynolds numbers that ranged between 2000 and 15000 and volume fractions of 2, 4, and 6 percent.The findings show that Reynolds number and concentration of nanoparticles have a strong effect on thermal performance. The overall heat transfer coefficient of CNT-SiC/water, MgO-Fe3O4/water, CuO-SiO2/water and Al2O3-TiO2/water enhanced by 34.27, 30.66, 28.27 and 27.39 percent respectively than pure water at 6% of volume concentration. Accordingly, the rate of heat transfer was enhanced by 26.18%, 23.31%, 21.48%, and 20.85%. CNT-SiC/water hybrid nanofluids showed the most significant thermal enhancement among the considered fluids that were studied. The results confirm that hybrid nanofluids considerably enhance the heat transfer performance at the expense of increased pressure loss with a significant level of importance of thermal-hydraulic optimization in practice.
- 3 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNumerical Study of the Effect of Hybrid Nanofluid Volume Fractions on the Thermal Hydraulic Efficiency of a Concentric Double Pipe Heat Exchanger
A key problem in sustainable thermal system design is to improve the efficiency of heat transfer. The application of nanofluids, especially the hybrid nanofluids has become a promising method of enhancing the performance of heat exchangers because of their great thermophysical characteristics. This paper has presented a numerical analysis to determine the rate of heat transfer, the overall heat transfer coefficient, and pressure drop of four hybrid nanofluids namely CNT-SiC/water, MgO-Fe3O4/water, Al2O3-TiO2/water and CuO-SiO2/water in the counter-flow concentric pipe heat exchanger in turbulent flow regime. The simulations were carried out with Reynolds numbers that ranged between 2000 and 15000 and volume fractions of 2, 4, and 6 percent.The findings show that Reynolds number and concentration of nanoparticles have a strong effect on thermal performance. The overall heat transfer coefficient of CNT-SiC/water, MgO-Fe3O4/water, CuO-SiO2/water and Al2O3-TiO2/water enhanced by 34.27, 30.66, 28.27 and 27.39 percent respectively than pure water at 6% of volume concentration. Accordingly, the rate of heat transfer was enhanced by 26.18%, 23.31%, 21.48%, and 20.85%. CNT-SiC/water hybrid nanofluids showed the most significant thermal enhancement among the considered fluids that were studied. The results confirm that hybrid nanofluids considerably enhance the heat transfer performance at the expense of increased pressure loss with a significant level of importance of thermal-hydraulic optimization in practice.
- 14 January 2022
- Published by Elsevier
- p. 189-222
Application of exhaust gas recirculation for NOx reduction in CI engines
- 14 January 2022
- Published by Elsevier
- p. 189-222
Application of exhaust gas recirculation for NOx reduction in CI engines
- 1 January 2017
- Published by Transstellar Journal Publications and Research Consultancy Private Limited in International Journal of Mechanical and Production Engineering Research and Development
- Vol. 7 (6) , 573-584
Addressing Nox - Smoke Trade off in a Direction Injection Diesel Engine With Fuel Blends of Diethyl Ether and Diesel
- 1 January 2017
- Published by Transstellar Journal Publications and Research Consultancy Private Limited in International Journal of Mechanical and Production Engineering Research and Development
- Vol. 7 (6) , 573-584
Addressing Nox - Smoke Trade off in a Direction Injection Diesel Engine With Fuel Blends of Diethyl Ether and Diesel
- Open Access
- 12 October 2015
- Published by Hindawi Limited in Journal of Thermodynamics
- Vol. 2015, 1-10
Influence of Exhaust Gas Recirculation, and Injection Timing on the Combustion, Performance and Emission Characteristics of a Cylinder Head Porous Medium Engine
Homogeneous combustion has the potential of achieving both near-zero emissions and low specific fuel consumption. However, the accomplishment of homogeneous combustion depends on the air flow structure inside the combustion chamber, fuel injection conditions, and turbulence as well as ignition conditions. Various methods and procedures are being adopted to establish the homogeneous combustion inside the engine cylinder. In this research work, a highly porous ceramic structure was introduced into the combustion chamber (underside of the cylinder head). The influence of operating parameters such as exhaust gas recirculation (EGR) and injection timing on the combustion, performance, and emission characteristics of such developed engine was investigated in this research work.
- 12 October 2015
- Published by Hindawi Limited in Journal of Thermodynamics
- Vol. 2015, 1-10
Open AccessInfluence of Exhaust Gas Recirculation, and Injection Timing on the Combustion, Performance and Emission Characteristics of a Cylinder Head Porous Medium Engine
Homogeneous combustion has the potential of achieving both near-zero emissions and low specific fuel consumption. However, the accomplishment of homogeneous combustion depends on the air flow structure inside the combustion chamber, fuel injection conditions, and turbulence as well as ignition conditions. Various methods and procedures are being adopted to establish the homogeneous combustion inside the engine cylinder. In this research work, a highly porous ceramic structure was introduced into the combustion chamber (underside of the cylinder head). The influence of operating parameters such as exhaust gas recirculation (EGR) and injection timing on the combustion, performance, and emission characteristics of such developed engine was investigated in this research work.
- Open Access
- 14 January 2014
- Published by Hindawi Limited in Chinese Journal of Engineering
- Vol. 2014, 1-5
Experimental Investigation on Usage of Palm Oil as a Lubricant to Substitute Mineral Oil in CI Engines
Due to growing environmental concerns, vegetable oils are finding their way into lubricants for industrial and transportation applications. The substitution of mineral oil with vegetable oil as a base stock for an environment friendly lubricant in a CI engine is explored in this study without adding any additives. The experiments have been conducted with a mixture of palm oil and mineral oil, at different compositions. Blends of palm oil and mineral oil in different compositions, 0, 25, and 50 (by vol %) were added to base SAE20W40 mineral oil to obtain different lubricant blends. The parameters evaluated include brake thermal efficiency, brake specific fuel consumption, volumetric efficiency, and mechanical efficiency and exhaust emissions. The engine performance and emission tests were carried out on a single cylinder, water cooled, 4-stroke CI engine. Compared to mineral oil, the palm oil-based lubricant revealed appreciable expedience on engine and emission performance.
- 14 January 2014
- Published by Hindawi Limited in Chinese Journal of Engineering
- Vol. 2014, 1-5
Open AccessExperimental Investigation on Usage of Palm Oil as a Lubricant to Substitute Mineral Oil in CI Engines
Due to growing environmental concerns, vegetable oils are finding their way into lubricants for industrial and transportation applications. The substitution of mineral oil with vegetable oil as a base stock for an environment friendly lubricant in a CI engine is explored in this study without adding any additives. The experiments have been conducted with a mixture of palm oil and mineral oil, at different compositions. Blends of palm oil and mineral oil in different compositions, 0, 25, and 50 (by vol %) were added to base SAE20W40 mineral oil to obtain different lubricant blends. The parameters evaluated include brake thermal efficiency, brake specific fuel consumption, volumetric efficiency, and mechanical efficiency and exhaust emissions. The engine performance and emission tests were carried out on a single cylinder, water cooled, 4-stroke CI engine. Compared to mineral oil, the palm oil-based lubricant revealed appreciable expedience on engine and emission performance.
- 27 November 2013
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Optimization of GENSET Engine for CPCB- II Norms using Cost Effective Techniques
The major challenge that is faced by most of the engine manufacturers nowadays is to meet the stringent emission norms with least modification in the engine design. In achieving the emission norms simplicity of the design has to be maintained as far as possible by optimizing the available emission control techniques. This paper deals with such optimal technique with reduced cost and up gradation of the engine from CPCB I to CPCB II in minimum time with minimum design changes. This difficult task is achieved by adopting direct continuous EGR and intercooler with appropriate injection timing and optimizing the fuel injection pump in a cost effective manner. The experiment is carried out on 2.86 litre turbocharged engine giving power output 44.5 kW @1500 rpm. In order to achieve the NOx emission norms LLR FIP is used, to retard the injection timing at part loads to reduce the in-cylinder temperature. Direct continuous EGR is used to further reduce the NOx Emission and intercooler is used to reduce the BSFC.
- 27 November 2013
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Optimization of GENSET Engine for CPCB- II Norms using Cost Effective Techniques
The major challenge that is faced by most of the engine manufacturers nowadays is to meet the stringent emission norms with least modification in the engine design. In achieving the emission norms simplicity of the design has to be maintained as far as possible by optimizing the available emission control techniques. This paper deals with such optimal technique with reduced cost and up gradation of the engine from CPCB I to CPCB II in minimum time with minimum design changes. This difficult task is achieved by adopting direct continuous EGR and intercooler with appropriate injection timing and optimizing the fuel injection pump in a cost effective manner. The experiment is carried out on 2.86 litre turbocharged engine giving power output 44.5 kW @1500 rpm. In order to achieve the NOx emission norms LLR FIP is used, to retard the injection timing at part loads to reduce the in-cylinder temperature. Direct continuous EGR is used to further reduce the NOx Emission and intercooler is used to reduce the BSFC.
- Open Access
- 20 September 2013
- Published by Tech Science Press in Frontiers in Heat and Mass Transfer
- Vol. 4 (2)
STUDY OF INTERNAL FLOW CHARACTERISTICS OF INJECTOR FUELLED WITH VARIOUS BLENDS OF DIETHYL ETHER AND DIESEL USING CFD STUDY OF INTERNAL FLOW CHARACTERISTICS OF INJECTOR FUELLED WITH VARIOUS BLENDS OF DIETHYL ETHER AND DIESEL USING CFD
A premiere free-access and peer-reviewed frontier journal site, serving the needs of the thermal-fluids community. See the latest research or submit an article. Quickly share your research with the global thermal-fluids community, for increased citations and impact at no cost.
- 20 September 2013
- Published by Tech Science Press in Frontiers in Heat and Mass Transfer
- Vol. 4 (2)
Open AccessSTUDY OF INTERNAL FLOW CHARACTERISTICS OF INJECTOR FUELLED WITH VARIOUS BLENDS OF DIETHYL ETHER AND DIESEL USING CFD STUDY OF INTERNAL FLOW CHARACTERISTICS OF INJECTOR FUELLED WITH VARIOUS BLENDS OF DIETHYL ETHER AND DIESEL USING CFD
A premiere free-access and peer-reviewed frontier journal site, serving the needs of the thermal-fluids community. See the latest research or submit an article. Quickly share your research with the global thermal-fluids community, for increased citations and impact at no cost.
- Open Access
- 1 January 2011
- Published by National Library of Serbia in Thermal Science
- Vol. 15 (4) , 1123-1130
Numerical investigation on the effect of injection pressure on the internal flow characteristics for diethyl ether, dimethyl ether and diesel fuel injectors using CFD
The spray characteristics of the diesel fuel are greatly affected by the cavitation formed inside the injector due to the high pressure differential across the nozzle. Many researchers across the globe are exploring the potential of using diethyl ether and dimethyl ether as an alternate for diesel fuel to meet the strict emission norms. Due to the variation in the fuel properties the internal flow characteristics in injectors for ether fuels are expected to be different from that of the diesel fuel. In this paper computational technique is used to study and compare the internal flow characteristics of diethyl ether, dimethyl ether and diesel fuel. The two phase flow model considering the fuel as a mixture of liquid and vapor is adopted for the simulation study. The injection pressure is varied from 100 to 400 bar and the flow characteristics of all three fuels are simulated and compared. Results indicate that all three fuels have distinct cavitating patterns owing to different property values. The dimethyl ether is found to be more cavitating than diesel and diethyl ether fuels as expected. The mass of fuel injected are found to be decreasing for the ether fuels when compared with diesel fuel at all injection pressures.
- 1 January 2011
- Published by National Library of Serbia in Thermal Science
- Vol. 15 (4) , 1123-1130
Open AccessNumerical investigation on the effect of injection pressure on the internal flow characteristics for diethyl ether, dimethyl ether and diesel fuel injectors using CFD
The spray characteristics of the diesel fuel are greatly affected by the cavitation formed inside the injector due to the high pressure differential across the nozzle. Many researchers across the globe are exploring the potential of using diethyl ether and dimethyl ether as an alternate for diesel fuel to meet the strict emission norms. Due to the variation in the fuel properties the internal flow characteristics in injectors for ether fuels are expected to be different from that of the diesel fuel. In this paper computational technique is used to study and compare the internal flow characteristics of diethyl ether, dimethyl ether and diesel fuel. The two phase flow model considering the fuel as a mixture of liquid and vapor is adopted for the simulation study. The injection pressure is varied from 100 to 400 bar and the flow characteristics of all three fuels are simulated and compared. Results indicate that all three fuels have distinct cavitating patterns owing to different property values. The dimethyl ether is found to be more cavitating than diesel and diethyl ether fuels as expected. The mass of fuel injected are found to be decreasing for the ether fuels when compared with diesel fuel at all injection pressures.