Pavel Layus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Pavel Layus has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Paul Kah
Department of Engineering Science, University West, Trollhättan, Sweden
11 shared publications - Francois Njock Bayock
University of Douala
3 shared publications - Belinga Mvola
Lappeenranta University of Technology
2 shared publications Jukka Martikainen
Lappeenranta University of Technology
2 shared publicationsAlexander Zisman
Central Research Institute of Structural Materials Prometey, Saint-Petersburg, Russia
1 shared publicationBelinga Mvola
Laboratory of Welding Technology, Lappeenranta-Lahti University of Technology, P.O. Box 20, 53851 Lappeenranta, Finland
1 shared publication
Latest Publications
- 1 January 2020
- Published by Društvo za unapređivanje zavarivanja u Srbiji - DUZS in Zavarivanje i zavarene konstrukcije
- Vol. 65 (4) , 159-172
Characterization of bainite-ferrite structures formed on the heat-affected zone of a dissimilar welds of high-strength steel (S700MC/S960QC) and their dependency on cooling time
Modern steel structures and joints must satisfy various increasingly demanding requirements such as high yield strength, improved cross section to mass ratio, and desirable ductile-to-brittle transition properties. Consequently, joining different types of high-strength steels has become an attractive option from the cost perspective and for weight and corrosion reduction. In dissimilar welding, however, there remains a need for better understanding of discrepancies in microstructure formation resulting from asymmetric heat distribution. In this study, a characterization of the transformation of bainite, ferrite, and martensite in the microstructure of the heat affected zone (HAZ) formed by a cooling time of 10 kJ/cm of heat input was carried out for dissimilar high-strength joint steels (S700MC/S960QC). The characterization was performed by scan electron microscopy (SEM) sampling, the images of which were analyzed by ImageJ Pro and evaluated by volume fraction of block - like granular bainite (GB). The alloy elements composition close to the fusion line of both materials was then assessed using energy dispersive X-ray spectroscopy (EDS). The results showed a strong presence of GB, which had about 70% volume fraction in S700MC at 615 °C, and which comprised formations of lower bainite and retained austenite (RA) at 420 °C. The presence of 55% block GB was observed at 470 °C in S960QC, which was caused by the formation of tempered martensite (TMA) at 400 °C. Presence of 1.3Ni, 0.4Mo, and 1.6Mn in the coarse grain heat affected zone (CGHAZ) of S700MC confirmed the risk of brittle failure on the S700MC side due to the high presence of carbide and ferrite in the GB.
- 1 January 2020
- Published by Društvo za unapređivanje zavarivanja u Srbiji - DUZS in Zavarivanje i zavarene konstrukcije
- Vol. 65 (4) , 159-172
Characterization of bainite-ferrite structures formed on the heat-affected zone of a dissimilar welds of high-strength steel (S700MC/S960QC) and their dependency on cooling time
Modern steel structures and joints must satisfy various increasingly demanding requirements such as high yield strength, improved cross section to mass ratio, and desirable ductile-to-brittle transition properties. Consequently, joining different types of high-strength steels has become an attractive option from the cost perspective and for weight and corrosion reduction. In dissimilar welding, however, there remains a need for better understanding of discrepancies in microstructure formation resulting from asymmetric heat distribution. In this study, a characterization of the transformation of bainite, ferrite, and martensite in the microstructure of the heat affected zone (HAZ) formed by a cooling time of 10 kJ/cm of heat input was carried out for dissimilar high-strength joint steels (S700MC/S960QC). The characterization was performed by scan electron microscopy (SEM) sampling, the images of which were analyzed by ImageJ Pro and evaluated by volume fraction of block - like granular bainite (GB). The alloy elements composition close to the fusion line of both materials was then assessed using energy dispersive X-ray spectroscopy (EDS). The results showed a strong presence of GB, which had about 70% volume fraction in S700MC at 615 °C, and which comprised formations of lower bainite and retained austenite (RA) at 420 °C. The presence of 55% block GB was observed at 470 °C in S960QC, which was caused by the formation of tempered martensite (TMA) at 400 °C. Presence of 1.3Ni, 0.4Mo, and 1.6Mn in the coarse grain heat affected zone (CGHAZ) of S700MC confirmed the risk of brittle failure on the S700MC side due to the high presence of carbide and ferrite in the GB.
- Open Access
Effect of Heat Input and Undermatched Filler Wire on the Microstructure and Mechanical Properties of Dissimilar S700MC/S960QC High-Strength Steels
The effect of heat input on the microstructure and mechanical properties of dissimilar S700MC/S960QC high-strength steels (HSS) using undermatched filler material was evaluated. Experiments were performed using the gas metal arc welding process to weld three samples, which had three different heat input values (i.e., 15 kJ/cm, 7 kJ/cm, and 10 kJ/cm). The cooling continuous temperature (CCT) diagrams, macro-hardness values, microstructure formations, alloy element compositions, and tensile test analyses were performed with the aim of providing valuable information for improving the strength of the heat-affected zone (HAZ) of both materials. Micro-hardness measurement was conducted using the Vickers hardness test and microstructural evaluation by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The mechanical properties were characterized by tensile testing. Dissimilar welded samples (S700MC/S960QC) with a cooling rate of 10 °C/s (15 kJ/cm) showed a lower than average hardness (210 HV5) in the HAZ of S700MC than S960QC. This hardness was 18% lower compared to the value of the base material (BM). The best microstructure formation was obtained using a heat input of 10 kJ/cm, which led to the formation of bainite (B, 60% volume fraction), ferrite (F, 25% volume fraction), and retained austenite (RA, 10%) in the final microstructure of S700MC, and B (55%), martensite (M, 45%), and RA (10%), which developed at the end of the transformation of S960QC. The results showed the presence of 1.3 Ni, 0.4 Mo, and 1.6 Mn in the fine-grain heat-affected zone of S700MC. The formation of a higher carbide content at a lower cooling rate reduced both the hardness and strength.
Open AccessEffect of Heat Input and Undermatched Filler Wire on the Microstructure and Mechanical Properties of Dissimilar S700MC/S960QC High-Strength Steels
The effect of heat input on the microstructure and mechanical properties of dissimilar S700MC/S960QC high-strength steels (HSS) using undermatched filler material was evaluated. Experiments were performed using the gas metal arc welding process to weld three samples, which had three different heat input values (i.e., 15 kJ/cm, 7 kJ/cm, and 10 kJ/cm). The cooling continuous temperature (CCT) diagrams, macro-hardness values, microstructure formations, alloy element compositions, and tensile test analyses were performed with the aim of providing valuable information for improving the strength of the heat-affected zone (HAZ) of both materials. Micro-hardness measurement was conducted using the Vickers hardness test and microstructural evaluation by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The mechanical properties were characterized by tensile testing. Dissimilar welded samples (S700MC/S960QC) with a cooling rate of 10 °C/s (15 kJ/cm) showed a lower than average hardness (210 HV5) in the HAZ of S700MC than S960QC. This hardness was 18% lower compared to the value of the base material (BM). The best microstructure formation was obtained using a heat input of 10 kJ/cm, which led to the formation of bainite (B, 60% volume fraction), ferrite (F, 25% volume fraction), and retained austenite (RA, 10%) in the final microstructure of S700MC, and B (55%), martensite (M, 45%), and RA (10%), which developed at the end of the transformation of S960QC. The results showed the presence of 1.3 Ni, 0.4 Mo, and 1.6 Mn in the fine-grain heat-affected zone of S700MC. The formation of a higher carbide content at a lower cooling rate reduced both the hardness and strength.
- Open Access
Numerical and Experimental Investigation of the Heat Input Effect on the Mechanical Properties and Microstructure of Dissimilar Weld Joints of 690-MPa QT and TMCP Steel
The study evaluates numerically and experimentally the effect of welding heat input parameters on the microstructure and hardness of the heat-affected zone (HAZ) of quenched and tempered (QT) and thermo-mechanically controlled process (TMCP) 690-MPa high-strength steel. Numerical analyses and experimental comparisons were applied using three heat input values (10, 14, and 17 kJ/cm) in order to predict the thermal fields during welding. Experimental analysis was carried out of the microstructure and microhardness behavior in different HAZ areas. The numerical values indicate that the maximum respective values of temperature measured in QT steel and TMCP steel were about 1300 and 1200 °C for a heat input of 10 kJ/cm, 1400 and 1300 °C for a heat input of 14 kJ/cm, and 1600 and 1450 °C for a heat input of 17 kJ/cm. The cooling times resulted, for a heat input of 10 kJ/cm, in numerical t8/5 (14.5 s) and experimental (18.84 s) increases in hardness in the coarse-grain heat-affected zone (CGHAZ) of the QT steel (317 HV0.1), due to the formation of bainite and lath martensite structures with grain growth. Decreased hardness in the CGHAZ of TMCP steel (240 HV0.1) was caused by primary recrystallization of the microstructure and the formation of more equilibrium products of austenite decomposition. Increasing the heat input (14 to 17 kJ/cm) led to numerical t8/5 (29 s) and experimental (36 s) decreases in hardness in the CGHAZ of QT steel (270 HV0.1) due to the full austenite (thermal weld cycle), and maintained the relative value of TMCP steel (235 HV0.1).
Open AccessNumerical and Experimental Investigation of the Heat Input Effect on the Mechanical Properties and Microstructure of Dissimilar Weld Joints of 690-MPa QT and TMCP Steel
The study evaluates numerically and experimentally the effect of welding heat input parameters on the microstructure and hardness of the heat-affected zone (HAZ) of quenched and tempered (QT) and thermo-mechanically controlled process (TMCP) 690-MPa high-strength steel. Numerical analyses and experimental comparisons were applied using three heat input values (10, 14, and 17 kJ/cm) in order to predict the thermal fields during welding. Experimental analysis was carried out of the microstructure and microhardness behavior in different HAZ areas. The numerical values indicate that the maximum respective values of temperature measured in QT steel and TMCP steel were about 1300 and 1200 °C for a heat input of 10 kJ/cm, 1400 and 1300 °C for a heat input of 14 kJ/cm, and 1600 and 1450 °C for a heat input of 17 kJ/cm. The cooling times resulted, for a heat input of 10 kJ/cm, in numerical t8/5 (14.5 s) and experimental (18.84 s) increases in hardness in the coarse-grain heat-affected zone (CGHAZ) of the QT steel (317 HV0.1), due to the formation of bainite and lath martensite structures with grain growth. Decreased hardness in the CGHAZ of TMCP steel (240 HV0.1) was caused by primary recrystallization of the microstructure and the formation of more equilibrium products of austenite decomposition. Increasing the heat input (14 to 17 kJ/cm) led to numerical t8/5 (29 s) and experimental (36 s) decreases in hardness in the CGHAZ of QT steel (270 HV0.1) due to the full austenite (thermal weld cycle), and maintained the relative value of TMCP steel (235 HV0.1).
- 30 April 2018
- Published by Praise Worthy Prize in International Review of Mechanical Engineering (IREME)
- Vol. 12 (4) , 371
Adaptive Welding of S960QC UHSS for Arctic Structural Applications
Adaptive Welding of S960QC UHSS for Arctic Structural Applications
- 30 April 2018
- Published by Praise Worthy Prize in International Review of Mechanical Engineering (IREME)
- Vol. 12 (4) , 371
Adaptive Welding of S960QC UHSS for Arctic Structural Applications
Adaptive Welding of S960QC UHSS for Arctic Structural Applications
- 22 March 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 96 (9-12) , 4243-4265
Review of current waveform control effects on weld geometry in gas metal arc welding process
- 22 March 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 96 (9-12) , 4243-4265
Review of current waveform control effects on weld geometry in gas metal arc welding process
- Open Access
- 5 February 2018
- Published by Springer Nature in International Journal of Mechanical and Materials Engineering
- Vol. 13 (1) , 3
Study of the sensitivity of high-strength cold-resistant shipbuilding steels to thermal cycle of arc welding
- 5 February 2018
- Published by Springer Nature in International Journal of Mechanical and Materials Engineering
- Vol. 13 (1) , 3
Open AccessStudy of the sensitivity of high-strength cold-resistant shipbuilding steels to thermal cycle of arc welding
- Open Access
- 14 April 2016
- Published by Springer Nature in International Journal of Mechanical and Materials Engineering
- Vol. 11 (1) , 1-15
Evaluation of applicability of thick E500 TMCP and F500W QT steel plates for Arctic service
- 14 April 2016
- Published by Springer Nature in International Journal of Mechanical and Materials Engineering
- Vol. 11 (1) , 1-15
Open AccessEvaluation of applicability of thick E500 TMCP and F500W QT steel plates for Arctic service
- Open Access
- 15 March 2016
- Published by Springer Nature in International Journal of Mechanical and Materials Engineering
- Vol. 11 (1) , 1-7
Recrystallization-based formation of uniform fine-grained austenite structure before polymorphic transition in high-strength steels for Arctic applications
- 15 March 2016
- Published by Springer Nature in International Journal of Mechanical and Materials Engineering
- Vol. 11 (1) , 1-7
Open AccessRecrystallization-based formation of uniform fine-grained austenite structure before polymorphic transition in high-strength steels for Arctic applications
- 7 March 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 232 (1) , 114-127
Advanced submerged arc welding processes for Arctic structures and ice-going vessels
The Arctic region is expected to play an extremely prominent role in the future of the oil and gas industry as growing demand for natural resources leads to greater exploitation of a region that holds about 25% of the world’s oil and gas reserves. It has become clear that ensuring the necessary reliability of Arctic industrial structures is highly dependent on the welding processes used and the materials employed. The main challenge for welding in Arctic conditions is prevention of the formation of brittle fractures in the weld and base material. One mitigating solution to obtain sufficiently low-transition temperatures of the weld is use of a suitable welding process with properly selected parameters. This work provides a comprehensive review with experimental study of modified submerged arc welding processes used for Arctic applications, such as narrow gap welding, multi-wire welding, and welding with metal powder additions. Case studies covered in this article describe welding of Arctic steels such as X70 12.7-mm plate by multi-wire welding technique. Advanced submerged arc welding processes are compared in terms of deposition rate and welding process operational parameters, and the advantages and disadvantages of each process with respect to low-temperature environment applications are listed. This article contributes to the field by presenting a comprehensive state-of-the-art review and case studies of the most common submerged arc welding high deposition modifications. Each modification is reviewed in detail, facilitating understanding and assisting in correct selection of appropriate welding processes and process parameters.
- 7 March 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 232 (1) , 114-127
Advanced submerged arc welding processes for Arctic structures and ice-going vessels
The Arctic region is expected to play an extremely prominent role in the future of the oil and gas industry as growing demand for natural resources leads to greater exploitation of a region that holds about 25% of the world’s oil and gas reserves. It has become clear that ensuring the necessary reliability of Arctic industrial structures is highly dependent on the welding processes used and the materials employed. The main challenge for welding in Arctic conditions is prevention of the formation of brittle fractures in the weld and base material. One mitigating solution to obtain sufficiently low-transition temperatures of the weld is use of a suitable welding process with properly selected parameters. This work provides a comprehensive review with experimental study of modified submerged arc welding processes used for Arctic applications, such as narrow gap welding, multi-wire welding, and welding with metal powder additions. Case studies covered in this article describe welding of Arctic steels such as X70 12.7-mm plate by multi-wire welding technique. Advanced submerged arc welding processes are compared in terms of deposition rate and welding process operational parameters, and the advantages and disadvantages of each process with respect to low-temperature environment applications are listed. This article contributes to the field by presenting a comprehensive state-of-the-art review and case studies of the most common submerged arc welding high deposition modifications. Each modification is reviewed in detail, facilitating understanding and assisting in correct selection of appropriate welding processes and process parameters.
- 27 April 2015
- Published by Taylor & Francis in Welding International
- Vol. 30 (2) , 129-132
Effect of heat input on the mechanical properties of welded joints in high-strength steels
Experiments were carried out to determine the properties of the welded joints in 8 mm thick high-strength steels produced by quenching and tempering and thermomechanical rolling with accelerated cooling (tensile strength 821–835 MPa). The dependence of the strength, elongation, hardness, impact energy and crack opening displacement on the heat input in the range 1.0–0.7 kJ mm− 1 was determined. The results show that the dependence of the strength of the welded joints decreases and that of the elongation increases. The heat input has only a slight effect on the impact energy and crack opening displacement in the heat-affected zone.
- 27 April 2015
- Published by Taylor & Francis in Welding International
- Vol. 30 (2) , 129-132
Effect of heat input on the mechanical properties of welded joints in high-strength steels
Experiments were carried out to determine the properties of the welded joints in 8 mm thick high-strength steels produced by quenching and tempering and thermomechanical rolling with accelerated cooling (tensile strength 821–835 MPa). The dependence of the strength, elongation, hardness, impact energy and crack opening displacement on the heat input in the range 1.0–0.7 kJ mm− 1 was determined. The results show that the dependence of the strength of the welded joints decreases and that of the elongation increases. The heat input has only a slight effect on the impact energy and crack opening displacement in the heat-affected zone.