Shunsuke Yamakawa
Research Subjects
Shunsuke Yamakawa has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
Ryoji Asahi
8 shared publicationsHisatsugu Yamasaki
4 shared publicationsNaoki Hasegawa
Toyota Central R&D Labs., Inc
4 shared publicationsShi-Aki Hyodo
Toyota Central R&D Labs., Inc., Nagakute, Aichi, Japan
4 shared publications- Shuhei Yoshino
Toyota Central Research and Development Laboratories, Inc., 41-1, Yokomichi, Nagakute-city, Aichi 480-1118, Japan
4 shared publications - Shuji Yomo
Toyota Central R&D Labs., Inc
4 shared publications
Latest Publications
- 1 December 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (12) , 124504
Impact of Platinum/Carbon Aggregate Size on Agglomerate Structure and Performance of Polymer Electrolyte Fuel Cells
The aggregate size of Pt/C plays a crucial role in determining the agglomerate structure formed in catalyst inks and the porous structure of catalyst layers (CLs); consequently, it strongly influences the performance of polymer electrolyte fuel cells (PEFCs). To elucidate the underlying mechanism, we controlled the Pt/C aggregate size by varying the number of ball-milling cycles and evaluated the resulting agglomerate structures and CL properties. Large aggregates, with limited outer surface area for ionomer adsorption that allows hydrophobic interactions among Pt/C aggregates to dominate, promoted flocculation and the formation of coarse agglomerates, leading to non-uniform CLs and poor proton-conduction pathways within the agglomerates. As a result, platinum utilization decreased, and cell performance deteriorated. In contrast, smaller aggregates provided sufficient ionomer adsorption, balancing electrostatic repulsion and hydrophobic attraction. This facilitated colloidal gel formation and yielded uniform CLs. Improved ionomer coverage increased platinum utilization and mitigated oxygen transport resistance, leading to enhanced performance. Overall, these findings highlight that precise control of aggregate size is essential not only for stabilizing catalyst inks but also for designing CL microstructures that enable high-performance PEFC electrodes.
- 1 December 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (12) , 124504
Impact of Platinum/Carbon Aggregate Size on Agglomerate Structure and Performance of Polymer Electrolyte Fuel Cells
The aggregate size of Pt/C plays a crucial role in determining the agglomerate structure formed in catalyst inks and the porous structure of catalyst layers (CLs); consequently, it strongly influences the performance of polymer electrolyte fuel cells (PEFCs). To elucidate the underlying mechanism, we controlled the Pt/C aggregate size by varying the number of ball-milling cycles and evaluated the resulting agglomerate structures and CL properties. Large aggregates, with limited outer surface area for ionomer adsorption that allows hydrophobic interactions among Pt/C aggregates to dominate, promoted flocculation and the formation of coarse agglomerates, leading to non-uniform CLs and poor proton-conduction pathways within the agglomerates. As a result, platinum utilization decreased, and cell performance deteriorated. In contrast, smaller aggregates provided sufficient ionomer adsorption, balancing electrostatic repulsion and hydrophobic attraction. This facilitated colloidal gel formation and yielded uniform CLs. Improved ionomer coverage increased platinum utilization and mitigated oxygen transport resistance, leading to enhanced performance. Overall, these findings highlight that precise control of aggregate size is essential not only for stabilizing catalyst inks but also for designing CL microstructures that enable high-performance PEFC electrodes.
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (41) , 2046
Effect of Aggregate Size of Platinum-Supported Carbon on Colloidal Gel Formation in Catalyst Inks and Cell Performance in Polymer Electrolyte Fuel Cells
The dispersion stability of catalyst inks and the cell performance of the resulting catalyst layer in polymer electrolyte fuel cells are influenced by the type of platinum-supported carbon (Pt/C) used. However, the specific effects of Pt/C properties remain unclear. In this study, we focus on the effect of Pt/C aggregate size and investigate its impact on the formation of colloidal gel in catalyst inks—a stable agglomerate structure that contributes to dispersion stability—as well as on the resulting cell performance. To achieve this, the aggregate size was controlled by varying the number of ball milling (BM) cycles: 1, 5, and 10. When the aggregate size is large (1 and 5 BM cycles), colloidal gel formation is hindered because the limited outer surface area of larger aggregates reduces ionomer adsorption, weakening electrostatic repulsion (Fig. 1, top). As a result, sedimentation of Pt/C dominates over Brownian motion. Additionally, restricted ionomer penetration into larger aggregates limits ion conduction pathways, leading to low platinum utilization and suboptimal cell performance (Fig. 2). In contrast, when the Pt/C aggregate size is small (10 BM cycles), colloidal gel formation is promoted because the increased outer surface area enhances ionomer adsorption and strengthens electrostatic repulsion (Fig. 1, bottom). As a result, Brownian motion dominates over sedimentation. Moreover, the smaller aggregates allow more platinum sites to become accessible to the ionomer, enhancing catalyst utilization and improving cell performance (Fig. 2). Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (41) , 2046
Effect of Aggregate Size of Platinum-Supported Carbon on Colloidal Gel Formation in Catalyst Inks and Cell Performance in Polymer Electrolyte Fuel Cells
The dispersion stability of catalyst inks and the cell performance of the resulting catalyst layer in polymer electrolyte fuel cells are influenced by the type of platinum-supported carbon (Pt/C) used. However, the specific effects of Pt/C properties remain unclear. In this study, we focus on the effect of Pt/C aggregate size and investigate its impact on the formation of colloidal gel in catalyst inks—a stable agglomerate structure that contributes to dispersion stability—as well as on the resulting cell performance. To achieve this, the aggregate size was controlled by varying the number of ball milling (BM) cycles: 1, 5, and 10. When the aggregate size is large (1 and 5 BM cycles), colloidal gel formation is hindered because the limited outer surface area of larger aggregates reduces ionomer adsorption, weakening electrostatic repulsion (Fig. 1, top). As a result, sedimentation of Pt/C dominates over Brownian motion. Additionally, restricted ionomer penetration into larger aggregates limits ion conduction pathways, leading to low platinum utilization and suboptimal cell performance (Fig. 2). In contrast, when the Pt/C aggregate size is small (10 BM cycles), colloidal gel formation is promoted because the increased outer surface area enhances ionomer adsorption and strengthens electrostatic repulsion (Fig. 1, bottom). As a result, Brownian motion dominates over sedimentation. Moreover, the smaller aggregates allow more platinum sites to become accessible to the ionomer, enhancing catalyst utilization and improving cell performance (Fig. 2). Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (41) , 2044
( Invited ) Impact of Catalyst Ink Properties on Performance and Processability in Polymer Electrolyte Fuel Cells
Improving the processability of the catalyst layers (CL) in polymer electrolyte fuel cells (PEFCs), without compromising the CL performance, is essential for achieving affordable PEFCs and their widespread adoption. As the CL is formed from the catalyst ink, controlling the agglomerate structure (i.e., flocculation of Pt/C aggregates) and ionomer distribution in the ink is a key factor to achieve high processability and performance [1]. The agglomerate structure determines ink viscosity and the resulting porous structure of the CL, while adsorbed ionomers regulate this structure via electrostatic repulsion [2,3], and free ionomers, upon drying, adsorb onto the Pt surface, increasing oxygen transport resistance and suppressing catalytic activity through ionomer coverage [3-5]. Previous studies have reported the effects of ink’s processing properties (e.g., solvent compositions, dispersion methods) or material properties (e.g., type of support carbons or ionomers) on the processability, CL structure, and performance [4,7-9]. However, the detailed and systematic interpretation of the mechanism linking material and process factors to ink agglomerates and ionomer distribution, and ultimately to CL structures and their performance, has not yet been fully established. Here, we investigate the formation mechanisms of agglomerates and ionomer distribution in catalyst inks based on various process and material properties, and their impact on CL structure and performance. In this presentation, we focus on the effect of process variables including solvent composition and dispersion methods, and material properties such as the type of Pt/C and ionomer concentration in its stock solution, on agglomerate formation and ionomer distribution within catalyst inks [2,10]. Structural features of agglomerates and ionomer distributions in inks and CLs were analyzed using a concentrated laser particle size analyzer, ultra-small-angle X-ray scattering (USAXS), ultra-small-angle neutron scattering (USANS) [10], while finer structures were investigated by transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). We place particular emphasis on quantitatively understanding the ionomer adsorption ratio (Γ), defined as the weight fraction of ionomers adsorbed onto Pt/C relative to the total ionomer content in the ink, as it plays a key role in determining the agglomerate structure [2]. Our approach demonstrated that adjusting the solvent composition and dispersion methods according to Pt/C properties—including aggregate size and fractal dimension, surface functional group density, and Pt weight percent—enabled the optimization of Г. This led to smaller and more uniform agglomerates that were less sensitive to solid concentration during drying, thereby improving sedimentation stability. As a consequence, the resulting uniform CL structures reduced membrane/CL interfacial H + transport resistance. Furthermore, varying the ionomer concentration in the stock solution revealed how associated micellar structural changes in the ionomer influence fuel cell performance. These findings show that optimizing solvent composition and dispersion conditions based on Pt/C characteristics enables control of ink microstructure and ionomer distribution in the CL, resulting in a well-balanced improvement in both fuel cell performance and sedimentation stability. Reference [1] S. A. Berlinger, S. Garg, and A. Z. Weber, Curr. Opin. Electrochem ., 29 , 100744 (2021). [2] S. Yoshino, M. Harada, N. Hasegawa, and R. Jinnouchi, Colloids Surf., A , 667 , 127153 (2024). [3] S. Takahashi, T. Mashio, N. Horibe, K. Akizuki, and A. Ohma, ChemElectroChem , 2 , 1560 (2015). [4] A. Kobayashi, T. Fujii, C. Harada, E. Yasumoto, K. Takeda, K. Kakinuma, and M. Uchida, ACS Appl. Energy Mater ., 4 , 2307 (2021). [5] R. Jinnouchi, K. Kudo, K. Kodama, N. Kitano, T. Suzuki, S. Minami, K. Shinozaki, N. Hasegawa, and A. Shinohara, Nat. Commun ., 12 , 4956 (2021). [7] T. Van Cleve, S. Khandavalli, A. Chowdhury, S. Medina, S. Pylypenko, M. Wang, K. L. More, N. Kariuki, D. J. Myers, A. Z. Weber, S. A. Mauger, M. Ulsh, and K. C. Neyerlin, ACS Appl. Mater. Interfaces , 11 , 46953 (2019). [8] M. Wang, J. H. Park, S. Kabir, K. C. Neyerlin, N. N. Kariuki, H. Lv, V. R. Stamenkovic, D. J. Myers, M. Ulsh, and S. A. Mauger, ACS Appl. Energy Mater ., 2 , 6417 (2019). [9] H. Ren, Y. Teng, X. Meng, D. Fang, H. Huang, J. Geng, and Z. Shao, J. Power Sources, 506 (2021). [10] M. Harada, S. Kajiya, T. Mitsuoka, S.-i. Takata, H. Iwase, and H. Aoki, Colloids Surf., A , 665 , 131183 (2023).
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (41) , 2044
( Invited ) Impact of Catalyst Ink Properties on Performance and Processability in Polymer Electrolyte Fuel Cells
Improving the processability of the catalyst layers (CL) in polymer electrolyte fuel cells (PEFCs), without compromising the CL performance, is essential for achieving affordable PEFCs and their widespread adoption. As the CL is formed from the catalyst ink, controlling the agglomerate structure (i.e., flocculation of Pt/C aggregates) and ionomer distribution in the ink is a key factor to achieve high processability and performance [1]. The agglomerate structure determines ink viscosity and the resulting porous structure of the CL, while adsorbed ionomers regulate this structure via electrostatic repulsion [2,3], and free ionomers, upon drying, adsorb onto the Pt surface, increasing oxygen transport resistance and suppressing catalytic activity through ionomer coverage [3-5]. Previous studies have reported the effects of ink’s processing properties (e.g., solvent compositions, dispersion methods) or material properties (e.g., type of support carbons or ionomers) on the processability, CL structure, and performance [4,7-9]. However, the detailed and systematic interpretation of the mechanism linking material and process factors to ink agglomerates and ionomer distribution, and ultimately to CL structures and their performance, has not yet been fully established. Here, we investigate the formation mechanisms of agglomerates and ionomer distribution in catalyst inks based on various process and material properties, and their impact on CL structure and performance. In this presentation, we focus on the effect of process variables including solvent composition and dispersion methods, and material properties such as the type of Pt/C and ionomer concentration in its stock solution, on agglomerate formation and ionomer distribution within catalyst inks [2,10]. Structural features of agglomerates and ionomer distributions in inks and CLs were analyzed using a concentrated laser particle size analyzer, ultra-small-angle X-ray scattering (USAXS), ultra-small-angle neutron scattering (USANS) [10], while finer structures were investigated by transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). We place particular emphasis on quantitatively understanding the ionomer adsorption ratio (Γ), defined as the weight fraction of ionomers adsorbed onto Pt/C relative to the total ionomer content in the ink, as it plays a key role in determining the agglomerate structure [2]. Our approach demonstrated that adjusting the solvent composition and dispersion methods according to Pt/C properties—including aggregate size and fractal dimension, surface functional group density, and Pt weight percent—enabled the optimization of Г. This led to smaller and more uniform agglomerates that were less sensitive to solid concentration during drying, thereby improving sedimentation stability. As a consequence, the resulting uniform CL structures reduced membrane/CL interfacial H + transport resistance. Furthermore, varying the ionomer concentration in the stock solution revealed how associated micellar structural changes in the ionomer influence fuel cell performance. These findings show that optimizing solvent composition and dispersion conditions based on Pt/C characteristics enables control of ink microstructure and ionomer distribution in the CL, resulting in a well-balanced improvement in both fuel cell performance and sedimentation stability. Reference [1] S. A. Berlinger, S. Garg, and A. Z. Weber, Curr. Opin. Electrochem ., 29 , 100744 (2021). [2] S. Yoshino, M. Harada, N. Hasegawa, and R. Jinnouchi, Colloids Surf., A , 667 , 127153 (2024). [3] S. Takahashi, T. Mashio, N. Horibe, K. Akizuki, and A. Ohma, ChemElectroChem , 2 , 1560 (2015). [4] A. Kobayashi, T. Fujii, C. Harada, E. Yasumoto, K. Takeda, K. Kakinuma, and M. Uchida, ACS Appl. Energy Mater ., 4 , 2307 (2021). [5] R. Jinnouchi, K. Kudo, K. Kodama, N. Kitano, T. Suzuki, S. Minami, K. Shinozaki, N. Hasegawa, and A. Shinohara, Nat. Commun ., 12 , 4956 (2021). [7] T. Van Cleve, S. Khandavalli, A. Chowdhury, S. Medina, S. Pylypenko, M. Wang, K. L. More, N. Kariuki, D. J. Myers, A. Z. Weber, S. A. Mauger, M. Ulsh, and K. C. Neyerlin, ACS Appl. Mater. Interfaces , 11 , 46953 (2019). [8] M. Wang, J. H. Park, S. Kabir, K. C. Neyerlin, N. N. Kariuki, H. Lv, V. R. Stamenkovic, D. J. Myers, M. Ulsh, and S. A. Mauger, ACS Appl. Energy Mater ., 2 , 6417 (2019). [9] H. Ren, Y. Teng, X. Meng, D. Fang, H. Huang, J. Geng, and Z. Shao, J. Power Sources, 506 (2021). [10] M. Harada, S. Kajiya, T. Mitsuoka, S.-i. Takata, H. Iwase, and H. Aoki, Colloids Surf., A , 665 , 131183 (2023).
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (44) , 3033
The Impact of Support Carbon Properties on Ionomer Adsorption on Pt/C in Polymer Electrolyte Fuel Cell Catalyst Ink
In polymer electrolyte fuel cells, both the coatability and dispersion stability of catalyst inks, as well as the structure of the catalyst layers, are significantly influenced by the agglomerate structure of the platinum-supported carbon (Pt/C) in the catalyst ink. The previous study reported that the ionomer adsorbed onto the Pt/C mainly determines this agglomerate structure. The study also presented that the ionomer adsorption is promoted by enhancing the solvent polarity, via intensifying hydrophobic interactions between the carbon and the ionomer backbone [1]. However, little is known about the impact of Pt/C aggregate properties, such as size, surface area, and surface hydrophobicity. The aggregate is the indivisible building block of the agglomerate, serving as the site where the ionomer adsorbs, and is composed of primary particles. Here, we present the impact of Pt/C properties on the ionomer adsorption. As shown in Fig. 1, the measured ionomer adsorption ratio Γ, which is defined as the ratio of the adsorbed ionomer to the total ionomer in the catalyst ink, can be accurately described as following Eq. (1),which is illustrated in Fig. 2, where Df and Ragg are the fractal dimension and radius of Pt/C aggregate, Am is the specific surface area of support carbon excluding the mesopore surface area (< 5 nm),ρacid is the surface density of the acidic functional groups on the carbon surface, and ρmax acid is the maximum value of at which ionomer adsorption ceases. The coefficients C0 and C1 are the parameters optimized to reproduce the measured Γ. The function represents the relationship between Γ and each property of the Pt/C particles as depicted in Fig. 3. As the surface area of support carbon increases, support carbon becomes capable of adsorbing more ionomers. Hence, Γ is proportional to Am. On the contrary, as the Pt/C aggregate, which consists of primarily particles, becomes larger and/or exhibits higher fractal dimension, Γ decreases because ionomers cannot penetrate into the interiors of aggregates. Hence, Γ is inversely proportional to Df and Ragg. In addition, Γ is also influenced by the hydrophilicity of carbon surfaces. In ρacid < ρmax acid, the carbon can adsorb a nearly constant amount of ionomer regardless of via hydrophobic interactions, while the amount sharply decreases in ρacid ≥ ρmax acid. The stepwise behavior is represented by 1 / (1+C0 exp{-k(1-ρacid /ρmax acid)}). Eq. (1) reasonably represents the observed trends and is highly beneficial to design the Pt/C agglomerate structure allowing for stable processing and high performance. Reference [1] Yoshino, S.; Harada, M.; Hasegawa, N.; Jinnouchi, R. Effects of Solvent Composition on Agglomerate Structure in Catalyst Ink for Polymer Electrolyte Fuel Cells. Colloids and Surfaces A: Physicochemical and Engineering Aspects 2024, 133847. DOI: https://doi.org/10.1016/j.colsurfa.2024.133847. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (44) , 3033
The Impact of Support Carbon Properties on Ionomer Adsorption on Pt/C in Polymer Electrolyte Fuel Cell Catalyst Ink
In polymer electrolyte fuel cells, both the coatability and dispersion stability of catalyst inks, as well as the structure of the catalyst layers, are significantly influenced by the agglomerate structure of the platinum-supported carbon (Pt/C) in the catalyst ink. The previous study reported that the ionomer adsorbed onto the Pt/C mainly determines this agglomerate structure. The study also presented that the ionomer adsorption is promoted by enhancing the solvent polarity, via intensifying hydrophobic interactions between the carbon and the ionomer backbone [1]. However, little is known about the impact of Pt/C aggregate properties, such as size, surface area, and surface hydrophobicity. The aggregate is the indivisible building block of the agglomerate, serving as the site where the ionomer adsorbs, and is composed of primary particles. Here, we present the impact of Pt/C properties on the ionomer adsorption. As shown in Fig. 1, the measured ionomer adsorption ratio Γ, which is defined as the ratio of the adsorbed ionomer to the total ionomer in the catalyst ink, can be accurately described as following Eq. (1),which is illustrated in Fig. 2, where Df and Ragg are the fractal dimension and radius of Pt/C aggregate, Am is the specific surface area of support carbon excluding the mesopore surface area (< 5 nm),ρacid is the surface density of the acidic functional groups on the carbon surface, and ρmax acid is the maximum value of at which ionomer adsorption ceases. The coefficients C0 and C1 are the parameters optimized to reproduce the measured Γ. The function represents the relationship between Γ and each property of the Pt/C particles as depicted in Fig. 3. As the surface area of support carbon increases, support carbon becomes capable of adsorbing more ionomers. Hence, Γ is proportional to Am. On the contrary, as the Pt/C aggregate, which consists of primarily particles, becomes larger and/or exhibits higher fractal dimension, Γ decreases because ionomers cannot penetrate into the interiors of aggregates. Hence, Γ is inversely proportional to Df and Ragg. In addition, Γ is also influenced by the hydrophilicity of carbon surfaces. In ρacid < ρmax acid, the carbon can adsorb a nearly constant amount of ionomer regardless of via hydrophobic interactions, while the amount sharply decreases in ρacid ≥ ρmax acid. The stepwise behavior is represented by 1 / (1+C0 exp{-k(1-ρacid /ρmax acid)}). Eq. (1) reasonably represents the observed trends and is highly beneficial to design the Pt/C agglomerate structure allowing for stable processing and high performance. Reference [1] Yoshino, S.; Harada, M.; Hasegawa, N.; Jinnouchi, R. Effects of Solvent Composition on Agglomerate Structure in Catalyst Ink for Polymer Electrolyte Fuel Cells. Colloids and Surfaces A: Physicochemical and Engineering Aspects 2024, 133847. DOI: https://doi.org/10.1016/j.colsurfa.2024.133847. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (41) , 2700
(Invited) Computational and Experimental Characterization of PEFC Electrode Structures
In polymer electrolyte fuel cells (PEFCs) that demand high-efficiency and high-power-density for vehicle applications, elucidating the structure of the cathode catalyst layer is crucial to maximize the catalytic activity, proton conductivity, electric conductivity, and mass transport. Complex hierarchical primary particle, aggregate, and agglomerate structures of the cathode catalyst layer, which contains ionomer and platinum (Pt) catalysts supported on carbon particles, hinder the identification of bottlenecks in power generation. Particularly in recent years, emerging high-performance mesoporous carbon has introduced further complexity [1,2]. This advanced material is known to improve the catalytic activity by reducing the poisoning of Pt active sites. However, the gas transport resistance of mesoporous carbon remains unknown. Pt particles may be located both inside and outside the mesopores of the primary particles. The resistance to gas transport for Pt particles inside mesopores, which are less likely to be covered by ionomers that significantly hinder gas transport [3,4], is expected to be low. However, if Pt is located too deeply within the mesopores, or if the pores are submerged, the gas transport resistance could become substantial. Here, we elucidate impacts of ionomers and water on gas transport resistance in a catalyst layer composed of mesoporous and solid carbons by combined experiments and simulations. A pressure-independent gas transport resistance (Rother) can be determined from the limiting current of the hydrogen oxidation reaction (HOR) under various relative humidity (RH) conditions [3]. Separate ex-situ N2 and water adsorption isotherms of the catalyst layer powders allow for determining the volume ratio of ionomers within the mesopores and the RH-dependent water content in the catalyst layer, respectively. Moreover, computational simulations based on information from 3-D virtual models of the catalyst layers, reconstructed from 3-D transmission electron microscopy images and the isotherms, can reveal further details about the interactions between pore structure, Pt placement, ionomer distribution, and humidity. Our experiments have shown that at low RH, the mesoporous carbon exhibits a lower Rother than the solid carbon. However, as RH increases, Rother sharply increases, and the difference in Rother between mesoporous and solid carbons decreases. The experiments also displayed a hysteresis of RH-dependent Rother similar to that in the water adsorption isotherm. All these results suggest significant impacts of liquid water condensed in the mesopores. The simulations indicated that the lower Rother of mesoporous carbon at low RH can be reproduced by assuming that gas transport resistance at the ionomer/Pt interface is reduced in the mesopores, where Pt particles are not fully covered by ionomers owing to limited ionomer penetrations. The simulations also showed that Rother significantly increases, as observed in the experiments, when the mesopores are filled with liquid water. These findings suggest that optimizing the mesopore structure and distributions of Pt particles, ionomers, and water is crucial for enhancing power density. References: [1] V. Yarlagadda et al., ACS Energy Letters 3 (2018) 618–621. [2] T. Takeshita et al., J. Electroanal. Chem. 871 (2020) 114250. [3] K. Shinozaki et al., J. Power Sources 565 (2023) 232909. [4] R. Jinnouchi et al., Nat. Commun. 12 (2021) 4956.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (41) , 2700
(Invited) Computational and Experimental Characterization of PEFC Electrode Structures
In polymer electrolyte fuel cells (PEFCs) that demand high-efficiency and high-power-density for vehicle applications, elucidating the structure of the cathode catalyst layer is crucial to maximize the catalytic activity, proton conductivity, electric conductivity, and mass transport. Complex hierarchical primary particle, aggregate, and agglomerate structures of the cathode catalyst layer, which contains ionomer and platinum (Pt) catalysts supported on carbon particles, hinder the identification of bottlenecks in power generation. Particularly in recent years, emerging high-performance mesoporous carbon has introduced further complexity [1,2]. This advanced material is known to improve the catalytic activity by reducing the poisoning of Pt active sites. However, the gas transport resistance of mesoporous carbon remains unknown. Pt particles may be located both inside and outside the mesopores of the primary particles. The resistance to gas transport for Pt particles inside mesopores, which are less likely to be covered by ionomers that significantly hinder gas transport [3,4], is expected to be low. However, if Pt is located too deeply within the mesopores, or if the pores are submerged, the gas transport resistance could become substantial. Here, we elucidate impacts of ionomers and water on gas transport resistance in a catalyst layer composed of mesoporous and solid carbons by combined experiments and simulations. A pressure-independent gas transport resistance (Rother) can be determined from the limiting current of the hydrogen oxidation reaction (HOR) under various relative humidity (RH) conditions [3]. Separate ex-situ N2 and water adsorption isotherms of the catalyst layer powders allow for determining the volume ratio of ionomers within the mesopores and the RH-dependent water content in the catalyst layer, respectively. Moreover, computational simulations based on information from 3-D virtual models of the catalyst layers, reconstructed from 3-D transmission electron microscopy images and the isotherms, can reveal further details about the interactions between pore structure, Pt placement, ionomer distribution, and humidity. Our experiments have shown that at low RH, the mesoporous carbon exhibits a lower Rother than the solid carbon. However, as RH increases, Rother sharply increases, and the difference in Rother between mesoporous and solid carbons decreases. The experiments also displayed a hysteresis of RH-dependent Rother similar to that in the water adsorption isotherm. All these results suggest significant impacts of liquid water condensed in the mesopores. The simulations indicated that the lower Rother of mesoporous carbon at low RH can be reproduced by assuming that gas transport resistance at the ionomer/Pt interface is reduced in the mesopores, where Pt particles are not fully covered by ionomers owing to limited ionomer penetrations. The simulations also showed that Rother significantly increases, as observed in the experiments, when the mesopores are filled with liquid water. These findings suggest that optimizing the mesopore structure and distributions of Pt particles, ionomers, and water is crucial for enhancing power density. References: [1] V. Yarlagadda et al., ACS Energy Letters 3 (2018) 618–621. [2] T. Takeshita et al., J. Electroanal. Chem. 871 (2020) 114250. [3] K. Shinozaki et al., J. Power Sources 565 (2023) 232909. [4] R. Jinnouchi et al., Nat. Commun. 12 (2021) 4956.
- 1 January 2020
- Published by Elsevier in Solid State Ionics
- Vol. 344
Effect of positive electrode microstructure in all-solid-state lithium-ion battery on high-rate discharge capability
- 1 January 2020
- Published by Elsevier in Solid State Ionics
- Vol. 344
Effect of positive electrode microstructure in all-solid-state lithium-ion battery on high-rate discharge capability
- 1 June 2018
- Published by Elsevier in Solid State Ionics
- Vol. 319, 209-217
Phase-field modeling of stress generation in polycrystalline LiCoO2
- 1 June 2018
- Published by Elsevier in Solid State Ionics
- Vol. 319, 209-217
Phase-field modeling of stress generation in polycrystalline LiCoO2
- Top Cited Papers
- 1 December 2017
- Published by Elsevier in Acta Materialia
- Vol. 141, 29-38
Microstructure recognition using convolutional neural networks for prediction of ionic conductivity in ceramics
- 1 December 2017
- Published by Elsevier in Acta Materialia
- Vol. 141, 29-38
Top Cited PapersMicrostructure recognition using convolutional neural networks for prediction of ionic conductivity in ceramics
- 26 July 2017
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 13 (35) , 5991-5999
Study of the conformation of polyelectrolyte aggregates using coarse-grained molecular dynamics simulations
The conformation of polyelectrolyte aggregates as a function of the backbone rigidity is investigated by coarse-grained molecular dynamics simulation.
- 26 July 2017
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 13 (35) , 5991-5999
Study of the conformation of polyelectrolyte aggregates using coarse-grained molecular dynamics simulations
The conformation of polyelectrolyte aggregates as a function of the backbone rigidity is investigated by coarse-grained molecular dynamics simulation.
- 3 May 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 5 (21) , 10658-10668
Effects of the microstructure of solid-electrolyte-coated LiCoO2 on its discharge properties in all-solid-state lithium batteries
Li-ion conduction in electrolyte materials and its intercalation properties in active materials are key factors that determine the electrochemical performances of batteries. Sulfide electrolyte coating onto active materials was done to form a favourable electrode–electrolyte interface and to increase the electrochemically active surface area. In this study, to obtain higher packing density pellets, a mixture of LiCoO2 particles with different grain sizes was used as a host material during the electrolyte deposition. The cell performance enhancement was achieved by the formation of a denser environment within composite electrodes. However, the influence of electrode microstructures on ion-conductive pathways has not been elucidated clearly and completely because of difficulties in conducting the experiments. In this context, a simulation model would provide insightful information about the potential of appropriate electrode structural designs. We proposed the implementation of the phase-field method, where the temporal evolution at electrode microstructures is calculated based on a free-energy function to construct realistic 3D images of the electrode structure. This study theoretically evaluated the constant current discharge properties of positive electrodes consisting of LiCoO2 with sulfide electrolyte coatings. The simulation results were able to reproduce an experimentally obtained correlation between the electrode potential and discharge capacity. The present simulation provided an estimation of the material properties required under specific discharge conditions. The preliminary examination demonstrated that the mutually connected fine network of ion-conductive pathways benefits from sulfide electrolyte coatings, and that it affects the discharge properties at higher rates than a conventional microstructure of mixed powder electrodes.
- 3 May 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 5 (21) , 10658-10668
Effects of the microstructure of solid-electrolyte-coated LiCoO2 on its discharge properties in all-solid-state lithium batteries
Li-ion conduction in electrolyte materials and its intercalation properties in active materials are key factors that determine the electrochemical performances of batteries. Sulfide electrolyte coating onto active materials was done to form a favourable electrode–electrolyte interface and to increase the electrochemically active surface area. In this study, to obtain higher packing density pellets, a mixture of LiCoO2 particles with different grain sizes was used as a host material during the electrolyte deposition. The cell performance enhancement was achieved by the formation of a denser environment within composite electrodes. However, the influence of electrode microstructures on ion-conductive pathways has not been elucidated clearly and completely because of difficulties in conducting the experiments. In this context, a simulation model would provide insightful information about the potential of appropriate electrode structural designs. We proposed the implementation of the phase-field method, where the temporal evolution at electrode microstructures is calculated based on a free-energy function to construct realistic 3D images of the electrode structure. This study theoretically evaluated the constant current discharge properties of positive electrodes consisting of LiCoO2 with sulfide electrolyte coatings. The simulation results were able to reproduce an experimentally obtained correlation between the electrode potential and discharge capacity. The present simulation provided an estimation of the material properties required under specific discharge conditions. The preliminary examination demonstrated that the mutually connected fine network of ion-conductive pathways benefits from sulfide electrolyte coatings, and that it affects the discharge properties at higher rates than a conventional microstructure of mixed powder electrodes.