Julio Ronceros
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Julio Ronceros has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Leonardo Vinces
Universidad Peruana de Ciencias Aplicadas
9 shared publications - Carlos Raymundo
Universidad Peruana de Ciencias Aplicadas
8 shared publications - Gianpierre Zapata
Universidad Peruana de Ciencias Aplicadas
7 shared publications - Gustavo Adolfo Ronceros Rivas
Faculty of Energy Engineering, Universidade Federal de Integração Latino-Americana (UNILA), Foz do Iguaçu 85870-650, Brazil
4 shared publications - Gustavo Ronceros
Engenharia de Energía, Universidade Federal de Integração Latino-americana (UNILA), Foz do Iguaçu, PR, 85870-650, Brazil
4 shared publications - Diego Rivera
Universidad Peruana de Ciencias Aplicadas
3 shared publications
Latest Publications
- Open Access
Internal Flow Analysis of a Dual-Swirl Dryer for Zingiberaceous Root Drying Through Numerical Simulation with Experimental Validation
Convective drying of Zingiberaceous roots, particularly ginger (Zingiber officinale), requires a uniform distribution of airflow and temperature to ensure energy efficiency and product quality. However, many drying systems exhibit aerothermal limitations that produce temperature gradients and non-uniform drying conditions. To address this issue, this study proposes a dual-swirl dryer featuring two air inlets: an upper helical inlet and a lower tangential inlet. Both inlet configurations generate swirling airflow patterns that enhance thermal uniformity and increase the residence time of hot air within the drying chamber. The internal flow behavior was investigated using Computational Fluid Dynamics (CFD) simulations in ANSYS Fluent2025 R1 version. A three-dimensional polyhedral mesh was generated to improve computational efficiency and numerical accuracy. Turbulence and recirculation phenomena were modeled using the Realizable k– turbulence model, while temperature distribution was analyzed through the energy conservation equation. Numerical predictions were experimentally validated using temperature sensors integrated into an automatic control system. The comparison between numerical and experimental results demonstrated that the dual-swirl configuration improves airflow redistribution, reduces thermal stagnation zones, and promotes a more homogeneous temperature field throughout the drying chamber. These findings confirm that the proposed system is an efficient alternative for agro-industrial drying applications.Open AccessInternal Flow Analysis of a Dual-Swirl Dryer for Zingiberaceous Root Drying Through Numerical Simulation with Experimental Validation
Convective drying of Zingiberaceous roots, particularly ginger (Zingiber officinale), requires a uniform distribution of airflow and temperature to ensure energy efficiency and product quality. However, many drying systems exhibit aerothermal limitations that produce temperature gradients and non-uniform drying conditions. To address this issue, this study proposes a dual-swirl dryer featuring two air inlets: an upper helical inlet and a lower tangential inlet. Both inlet configurations generate swirling airflow patterns that enhance thermal uniformity and increase the residence time of hot air within the drying chamber. The internal flow behavior was investigated using Computational Fluid Dynamics (CFD) simulations in ANSYS Fluent2025 R1 version. A three-dimensional polyhedral mesh was generated to improve computational efficiency and numerical accuracy. Turbulence and recirculation phenomena were modeled using the Realizable k– turbulence model, while temperature distribution was analyzed through the energy conservation equation. Numerical predictions were experimentally validated using temperature sensors integrated into an automatic control system. The comparison between numerical and experimental results demonstrated that the dual-swirl configuration improves airflow redistribution, reduces thermal stagnation zones, and promotes a more homogeneous temperature field throughout the drying chamber. These findings confirm that the proposed system is an efficient alternative for agro-industrial drying applications. - Open Access
- 15 October 2025
- Published by MDPI AG in Preprints.org
Classification of Friction Cracks in Railway Brake Discs Using Convolutional Neural Networks
Brake discs are critical components of a train’s pneumatic braking system and require monthly preventive maintenance, including cleaning, measurement, and visual inspection. Visual inspections, guided by standards such as UNE-EN 14535-3 and the Faiveley Transport technical manual, involve assessing cracks classified by size and type (penetrating, incipient, superficial). This study presents an automated solution for crack detection and classification using thermal imaging and artificial intelligence. A low-cost Flir Lepton 3.1R thermal camera was used to identify cracks based on size and location. The proposed method integrates the YOLOv8m model with a U-Net (ResNet50 backbone) and a CNN for improved detection and segmentation. Compared to previous approaches using YOLOv4 or Mask-RCNN, this combination provides higher precision in identifying thermal cracks on railway brake discs. The process begins with thermal image acquisition and data augmentation through noise injection and geometric transformations, producing a robust dataset for training the neural networks. Experimental results demonstrate the feasibility of applying AI and thermal imaging for predictive maintenance, achieving a 97% detection accuracy. Furthermore, the study confirms that using higher-resolution thermal datasets enhances model performance, making this approach a cost-effective and reliable tool for automated brake disc inspection.
- 15 October 2025
- Published by MDPI AG in Preprints.org
Open AccessClassification of Friction Cracks in Railway Brake Discs Using Convolutional Neural Networks
Brake discs are critical components of a train’s pneumatic braking system and require monthly preventive maintenance, including cleaning, measurement, and visual inspection. Visual inspections, guided by standards such as UNE-EN 14535-3 and the Faiveley Transport technical manual, involve assessing cracks classified by size and type (penetrating, incipient, superficial). This study presents an automated solution for crack detection and classification using thermal imaging and artificial intelligence. A low-cost Flir Lepton 3.1R thermal camera was used to identify cracks based on size and location. The proposed method integrates the YOLOv8m model with a U-Net (ResNet50 backbone) and a CNN for improved detection and segmentation. Compared to previous approaches using YOLOv4 or Mask-RCNN, this combination provides higher precision in identifying thermal cracks on railway brake discs. The process begins with thermal image acquisition and data augmentation through noise injection and geometric transformations, producing a robust dataset for training the neural networks. Experimental results demonstrate the feasibility of applying AI and thermal imaging for predictive maintenance, achieving a 97% detection accuracy. Furthermore, the study confirms that using higher-resolution thermal datasets enhances model performance, making this approach a cost-effective and reliable tool for automated brake disc inspection.
- Open Access
Numerical Study of a Hydraulic Turbine Designed from Centrifugal Atomizers Theory Varying Its Inlet Parameters
This study analyzes the feasibility of using pressure swirl atomizers at scale as energy generators. Likewise, the Ansys Fluent numerical simulation tool was used, configured based on the Volume of Fluid (VOF) multiphase model and six DOF motion for rigid bodies. In turn, three configurations of feeding flow were tested: upper manifold, lower manifold, and dual manifold. The numerical results show that it is possible to produce mechanical energy with 29.4% and 32.9% efficiency (using the SST k- and k- turbulence model, respectively), while generating a uniform spray effect at the outlet of the atomizer, even though this has certain ovoid-type deformities. Likewise, it was found that the addition of an internal rotor to the swirl chamber caused the generation of a very low-pressure contour, leading to an increase in the mass flow consumption of the atomizer. Also, four cases were analyzed, considering a hydraulic supply of both manifolds: 250 kPa, 300 kPa, 350 kPa, and 400 kPa, in order to obtain the characteristic curve of the turbine depending on the mass flow obtained for each case. Finally, this research proves how viable the use of this type of technology is in the field of renewable energy generation and the impact on its performance under different configurations of hydraulic supply.Open AccessNumerical Study of a Hydraulic Turbine Designed from Centrifugal Atomizers Theory Varying Its Inlet Parameters
This study analyzes the feasibility of using pressure swirl atomizers at scale as energy generators. Likewise, the Ansys Fluent numerical simulation tool was used, configured based on the Volume of Fluid (VOF) multiphase model and six DOF motion for rigid bodies. In turn, three configurations of feeding flow were tested: upper manifold, lower manifold, and dual manifold. The numerical results show that it is possible to produce mechanical energy with 29.4% and 32.9% efficiency (using the SST k- and k- turbulence model, respectively), while generating a uniform spray effect at the outlet of the atomizer, even though this has certain ovoid-type deformities. Likewise, it was found that the addition of an internal rotor to the swirl chamber caused the generation of a very low-pressure contour, leading to an increase in the mass flow consumption of the atomizer. Also, four cases were analyzed, considering a hydraulic supply of both manifolds: 250 kPa, 300 kPa, 350 kPa, and 400 kPa, in order to obtain the characteristic curve of the turbine depending on the mass flow obtained for each case. Finally, this research proves how viable the use of this type of technology is in the field of renewable energy generation and the impact on its performance under different configurations of hydraulic supply. - Open Access
- 31 December 2024
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 17 (6) , 57-68
Study of Internal Flow with Deceleration in a Cryogenic Chamber Composed of Jet-Type Atomizers
The present article delves into the comprehensive study of internal flow dynamics within a cryogenic chamber used for freezing food with high water percent. For cryogenic freezing is necessary to reduce temperature extremely and maintain a uniform distribution, different behaviours may cause structural damages on food. This is because the chamber comprises a circular-sectioned tunnel or chamber coupled with a set of Jet-type atomizers for the injection of liquid nitrogen. The internal flow, predominantly consisting of liquid nitrogen, necessitates prolonged residency within the chamber to uniformly and effectively cool or freeze food traversing its interior. Consequently, the primary aim is to extend the cryogenic fluid's residence time, achieved by strategically decelerating the flow. This deceleration is orchestrated through the strategic injection of the fluid to induce a swirling or vortex effect. The formation of this effect is meticulously executed by positioning the atomizers at periodic intervals around the internal walls of the cylindrical chamber, ensuring a prolonged recirculation of the internal flow. This research endeavour is further augmented by a comprehensive numerical analysis of swirling flow dynamics and associated parameters such as temperature, velocity, pressure and nitrogen-liquid interface. Leveraging the robust capabilities of CFD ANSYS software (Computational Fluid Dynamics), this analysis incorporates sophisticated models including the Volume of Fluid (VOF) model and the k-epsilon turbulence model. Additionally, the construction of a three-dimensional hexahedral mesh, facilitated by ICEM CFD software, adds depth and precision to the numerical simulations. The culmination of this study lies in the profound comprehension of internal flow behaviour and its intrinsic correlation with the design intricacies of the cryogenic system. Variations in nitrogen injection pressures and the strategic deployment of atomizers around the chamber serve as pivotal parameters for elucidating the system's optimal design
- 31 December 2024
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 17 (6) , 57-68
Open AccessStudy of Internal Flow with Deceleration in a Cryogenic Chamber Composed of Jet-Type Atomizers
The present article delves into the comprehensive study of internal flow dynamics within a cryogenic chamber used for freezing food with high water percent. For cryogenic freezing is necessary to reduce temperature extremely and maintain a uniform distribution, different behaviours may cause structural damages on food. This is because the chamber comprises a circular-sectioned tunnel or chamber coupled with a set of Jet-type atomizers for the injection of liquid nitrogen. The internal flow, predominantly consisting of liquid nitrogen, necessitates prolonged residency within the chamber to uniformly and effectively cool or freeze food traversing its interior. Consequently, the primary aim is to extend the cryogenic fluid's residence time, achieved by strategically decelerating the flow. This deceleration is orchestrated through the strategic injection of the fluid to induce a swirling or vortex effect. The formation of this effect is meticulously executed by positioning the atomizers at periodic intervals around the internal walls of the cylindrical chamber, ensuring a prolonged recirculation of the internal flow. This research endeavour is further augmented by a comprehensive numerical analysis of swirling flow dynamics and associated parameters such as temperature, velocity, pressure and nitrogen-liquid interface. Leveraging the robust capabilities of CFD ANSYS software (Computational Fluid Dynamics), this analysis incorporates sophisticated models including the Volume of Fluid (VOF) model and the k-epsilon turbulence model. Additionally, the construction of a three-dimensional hexahedral mesh, facilitated by ICEM CFD software, adds depth and precision to the numerical simulations. The culmination of this study lies in the profound comprehension of internal flow behaviour and its intrinsic correlation with the design intricacies of the cryogenic system. Variations in nitrogen injection pressures and the strategic deployment of atomizers around the chamber serve as pivotal parameters for elucidating the system's optimal design
- Open Access
Study of Internal Flow in a Liquid Nitrogen Flow Decelerator Through Swirl Effect Consisting of a Jet-Type Cryogenic Injection System for Food Freezing
This article addresses the study of internal flow dynamics within a cryogenic chamber designed for freezing food using liquid nitrogen injection. The chamber features a circular section with strategically placed jet-type atomizers for this purpose. The primary objective is to extend the residence time of the cryogenic fluid within the chamber to ensure uniform and effective freezing of the passing food items. This is achieved by inducing a swirl effect through strategic deceleration of the flow using the atomizers. The meticulous placement of these atomizers at periodic intervals along the internal walls of the cylindrical chamber ensures prolonged recirculation of the internal flow. Internal temperature analysis is crucial to ensure the freezing process. The study is supported by numerical analysis in CFD ANSYS to assess the dynamics of the swirl effect and parameters associated with the nitrogen–air interface, from which we obtain a sophisticated analysis thanks to the design of a hexahedral mesh made in greater detail in ICEM CFD. This approach aims to understand internal flow behavior and its correlation with the complexity of cryogenic system design, utilizing variable nitrogen-injection pressures and strategic atomizer placement as fundamental parameters to optimize system design.
Open AccessStudy of Internal Flow in a Liquid Nitrogen Flow Decelerator Through Swirl Effect Consisting of a Jet-Type Cryogenic Injection System for Food Freezing
This article addresses the study of internal flow dynamics within a cryogenic chamber designed for freezing food using liquid nitrogen injection. The chamber features a circular section with strategically placed jet-type atomizers for this purpose. The primary objective is to extend the residence time of the cryogenic fluid within the chamber to ensure uniform and effective freezing of the passing food items. This is achieved by inducing a swirl effect through strategic deceleration of the flow using the atomizers. The meticulous placement of these atomizers at periodic intervals along the internal walls of the cylindrical chamber ensures prolonged recirculation of the internal flow. Internal temperature analysis is crucial to ensure the freezing process. The study is supported by numerical analysis in CFD ANSYS to assess the dynamics of the swirl effect and parameters associated with the nitrogen–air interface, from which we obtain a sophisticated analysis thanks to the design of a hexahedral mesh made in greater detail in ICEM CFD. This approach aims to understand internal flow behavior and its correlation with the complexity of cryogenic system design, utilizing variable nitrogen-injection pressures and strategic atomizer placement as fundamental parameters to optimize system design.
- Open Access
Comprehensive Theoretical Formulation and Numerical Simulation of the Internal Flow in Pressure-Swirl Atomizers Type Screw-Conveyer
The present work shows the development of a comprehensive theoretical formulation for its application in the study of the internal flow of pressure-swirl atomizers with helical channels: “screw-conveyer”, which are characterized by presenting in their inlet channels, an angle of incidence or helix angle . This angle originates a trigonometric factor () that must be considered in the geometrical characteristics parameter of pressure-swirl atomizer (), which consequently involves other geometric parameters, such as the annular section coefficient (), discharge coefficient (), spray angle (), etc., being relevant in the internal flow study and design of the pressure-swirl atomizers type screw-conveyer. This theoretical formulation integrates an internal ideal flow model (Abramovich theory) with a model that considers the influence of the liquid viscosity (Kliachko theory) and hydraulic resistance of Idelchik. For the validation of this theoretical formulation, numerical simulation was used, considering the commercial software Ansys Fluent 2023 R2 furthermore, hexahedral meshes were generated with the ICEM CFD software 2023, for four cases of helix angle (, , and ), with application of the RNG k- turbulence model and VOF multiphase model (volume of fluid) for the location of the liquid-gas interface and spray angle visualization.Open AccessComprehensive Theoretical Formulation and Numerical Simulation of the Internal Flow in Pressure-Swirl Atomizers Type Screw-Conveyer
The present work shows the development of a comprehensive theoretical formulation for its application in the study of the internal flow of pressure-swirl atomizers with helical channels: “screw-conveyer”, which are characterized by presenting in their inlet channels, an angle of incidence or helix angle . This angle originates a trigonometric factor () that must be considered in the geometrical characteristics parameter of pressure-swirl atomizer (), which consequently involves other geometric parameters, such as the annular section coefficient (), discharge coefficient (), spray angle (), etc., being relevant in the internal flow study and design of the pressure-swirl atomizers type screw-conveyer. This theoretical formulation integrates an internal ideal flow model (Abramovich theory) with a model that considers the influence of the liquid viscosity (Kliachko theory) and hydraulic resistance of Idelchik. For the validation of this theoretical formulation, numerical simulation was used, considering the commercial software Ansys Fluent 2023 R2 furthermore, hexahedral meshes were generated with the ICEM CFD software 2023, for four cases of helix angle (, , and ), with application of the RNG k- turbulence model and VOF multiphase model (volume of fluid) for the location of the liquid-gas interface and spray angle visualization. - 21 August 2024
- Published by Springer Nature
- p. 184-194
Numerical Simulation of Internal Flow in Screw-Conveyor Atomizer from a Spraying Dust Suppression Device
- 21 August 2024
- Published by Springer Nature
- p. 184-194
Numerical Simulation of Internal Flow in Screw-Conveyor Atomizer from a Spraying Dust Suppression Device
- 30 July 2024
- Published by Springer Nature
- p. 251-262
Structural Model of a Hydrostatic Cryogenic Liquid Storage and Pressurization Tank in the Food Sector
- 30 July 2024
- Published by Springer Nature
- p. 251-262
Structural Model of a Hydrostatic Cryogenic Liquid Storage and Pressurization Tank in the Food Sector
- 30 July 2024
- Published by Springer Nature
- p. 263-271
Internal Flow Model of a Helical Centrifugal Atomizer for Cold Preservation Systems in the Fishing Industry
- 30 July 2024
- Published by Springer Nature
- p. 263-271
Internal Flow Model of a Helical Centrifugal Atomizer for Cold Preservation Systems in the Fishing Industry
- Open Access
- 9 July 2024
- Published by MDPI AG in Technologies
- Vol. 12 (7) , 107
Numerical Simulation and Design of a Mechanical Structure of an Ankle Exoskeleton for Elderly People
This article presents the numerical simulation and design of an ankle exoskeleton oriented to elderly users. For the design, anatomical measurements were taken from a user of this age group to obtain an ergonomic, resistant, and exceptionally reliable mechanical structure. In addition, the design was validated to support a “weight range” of users between 50 and 80 kg in order to evaluate the reaction of the mechanism within the range of loads generated in relation to the first principal stress, the safety coefficient, the Von Mises stress, and principal deformations, for which the 3D CAD software Autodesk Inventor and theoretical correlations were used to calculate the displacement and rotation angles of the ankle in the structure. Likewise, two types of materials were evaluated: ABS (acrylonitrile butadiene styrene) and a polymer reinforced with carbon fiber. Finally, the designed pieces were assembled with the guarantee that the mobility of the system had been validated through the numerical simulation environment, highlighting that by being generated through 3D printing, manufacturing costs are reduced, allowing them to be accessible and ensuring that more people can benefit from this ankle exoskeleton.
- 9 July 2024
- Published by MDPI AG in Technologies
- Vol. 12 (7) , 107
Open AccessNumerical Simulation and Design of a Mechanical Structure of an Ankle Exoskeleton for Elderly People
This article presents the numerical simulation and design of an ankle exoskeleton oriented to elderly users. For the design, anatomical measurements were taken from a user of this age group to obtain an ergonomic, resistant, and exceptionally reliable mechanical structure. In addition, the design was validated to support a “weight range” of users between 50 and 80 kg in order to evaluate the reaction of the mechanism within the range of loads generated in relation to the first principal stress, the safety coefficient, the Von Mises stress, and principal deformations, for which the 3D CAD software Autodesk Inventor and theoretical correlations were used to calculate the displacement and rotation angles of the ankle in the structure. Likewise, two types of materials were evaluated: ABS (acrylonitrile butadiene styrene) and a polymer reinforced with carbon fiber. Finally, the designed pieces were assembled with the guarantee that the mobility of the system had been validated through the numerical simulation environment, highlighting that by being generated through 3D printing, manufacturing costs are reduced, allowing them to be accessible and ensuring that more people can benefit from this ankle exoskeleton.