Ata Hojatkashani
Ata Hojatkashani has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
Abbas Akbarpour
2 shared publications- Abbas Akbarpour
Department of Civil Engineering, South Tehran Branch, Islamic Azad University, Tehran, Iran
2 shared publications - Hassan Abbasi
Department of Civil Engineering, South Tehran Branch, Islamic Azad University, Tehran, Iran
2 shared publications - Mohammad Zaman Kabir
Department of Civil and Environmental Engineering, Amirkabir University of Technology, Tehran, Iran
2 shared publications Vandad Garmeh
2 shared publications- Aida Rahmani
Centre for Infrastructure Engineering, Western Sydney University, Penrith, NSW 2751, Australia
1 shared publication
Latest Publications
- 9 January 2025
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 49 (5) , 4837-4856
Experimental, Numerical and Analytical Assessment of a new Multi-Level Damper with Steel Trapezoidal Plates
- 9 January 2025
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 49 (5) , 4837-4856
Experimental, Numerical and Analytical Assessment of a new Multi-Level Damper with Steel Trapezoidal Plates
- Open Access
- 30 July 2024
- Published by Springer Nature in Research Square
A Novel Evolutionary Algorithm-Based Approach for Optimizing the Mix Design of High-Performance Fiber-Reinforced Concrete (HPFRCC)
With the increasing demand for high-performance concrete, optimizing the design of high-performance alloy-armed compounds (HPFRCC) has become a major challenge. Optimizing the mix design enables the achievement of the desired stability and ductility. This study offers an innovative way to overcome this challenge using artificial intelligence (AI). Our method uses artificial neural networks (ANN) to model the relationship between the mixed component and final HPFRCC properties. Then, we explored a wide design space using advanced distribution algorithms to determine the best combination. These algorithms are inspired by nature, such as the evolutionary algorithm (EO), which replicates the scientific evolutionary process. This study significantly reduces the need for laboratory testing by employing innovative methodologies. This significant achievement significantly optimizes design time and cost. In addition, by comprehensively comparing EO performance with other similar algorithms, the excellence and innovation of the method were demonstrated in optimizing the complex design of the HPFRCC mixture, and a new multitarget optimization algorithm called FC-MOEO/AE was used to predict the HPFRCC combination. This method can be used as a design guide to guide decision-making in the pre-construction stage.
- 30 July 2024
- Published by Springer Nature in Research Square
Open AccessA Novel Evolutionary Algorithm-Based Approach for Optimizing the Mix Design of High-Performance Fiber-Reinforced Concrete (HPFRCC)
With the increasing demand for high-performance concrete, optimizing the design of high-performance alloy-armed compounds (HPFRCC) has become a major challenge. Optimizing the mix design enables the achievement of the desired stability and ductility. This study offers an innovative way to overcome this challenge using artificial intelligence (AI). Our method uses artificial neural networks (ANN) to model the relationship between the mixed component and final HPFRCC properties. Then, we explored a wide design space using advanced distribution algorithms to determine the best combination. These algorithms are inspired by nature, such as the evolutionary algorithm (EO), which replicates the scientific evolutionary process. This study significantly reduces the need for laboratory testing by employing innovative methodologies. This significant achievement significantly optimizes design time and cost. In addition, by comprehensively comparing EO performance with other similar algorithms, the excellence and innovation of the method were demonstrated in optimizing the complex design of the HPFRCC mixture, and a new multitarget optimization algorithm called FC-MOEO/AE was used to predict the HPFRCC combination. This method can be used as a design guide to guide decision-making in the pre-construction stage.
- 1 October 2023
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 176 (10) , 833-844
Compressive loading of structural insulated panels and conventional stud walls: a study
Structural insulated panels (SIPs) are structural elements comprising a core of expanded polystyrene insulation sandwiched between two oriented strand boards. They can replace conventional joist floors and stud walls in low-rise residential construction. Three identical samples of full-scale SIP walls and stud walls were tested according to ASTM standards and experimental results for the specimens were obtained in terms of their ultimate load capacity and failure mechanism. Comparison of the load–deformation diagrams of the SIPs and stud walls showed that tangential stiffness variation of the former occurred in the hardening mode, whereas the variation for the latter was in two stages, hardening and softening. Regarding compressive loading, the results showed that SIPs are as good as conventional wood framing of the same size. Therefore, SIP walls are very efficient in the case of axial compressive loading.
- 1 October 2023
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 176 (10) , 833-844
Compressive loading of structural insulated panels and conventional stud walls: a study
Structural insulated panels (SIPs) are structural elements comprising a core of expanded polystyrene insulation sandwiched between two oriented strand boards. They can replace conventional joist floors and stud walls in low-rise residential construction. Three identical samples of full-scale SIP walls and stud walls were tested according to ASTM standards and experimental results for the specimens were obtained in terms of their ultimate load capacity and failure mechanism. Comparison of the load–deformation diagrams of the SIPs and stud walls showed that tangential stiffness variation of the former occurred in the hardening mode, whereas the variation for the latter was in two stages, hardening and softening. Regarding compressive loading, the results showed that SIPs are as good as conventional wood framing of the same size. Therefore, SIP walls are very efficient in the case of axial compressive loading.
- 25 November 2022
- Published by Taylor & Francis in Structural Engineering International
- Vol. 34 (1) , 102-113
Nonlinear Seismic Analysis of Ground Structure to Evaluate the Capacity of a Permanent Tunnel Lining
In this paper, in addition to the linear analysis used for typical tunnels, nonlinear seismic analysis of a tunnel has been investigated using pseudo-static method and a damaged concrete behavior model introduced in ABAQUS® software. The simulations were carried out under three conditions, free field, ovaling and racking, at two hazardous earthquake levels according to an Operation Design Earthquake (ODE) and a Maximum Design Earthquake (MDE). Then, the structural capacity curve and the behavior factor for the final tunnel lining were obtained. In order to extend the studies as well as to verify the pseudo-static analyses, seven nonlinear dynamic analyses compatible with the site under MDE conditions have been performed. The results showed that the tunnel lining procedure created limited tensile cracks under compression. At the bottom corners of the tunnel structure, the resultant stresses in the tunnel lining under two earthquakes caused failure and created tensile cracks. Therefore, it was necessary to reinforce the lining at corners. Comparison between different nonlinear time history seismic analysis and pseudo-static methods indicated that the pseudo-static methods resulted in 10–30% less acceleration than the average results obtained from time history analysis.
- 25 November 2022
- Published by Taylor & Francis in Structural Engineering International
- Vol. 34 (1) , 102-113
Nonlinear Seismic Analysis of Ground Structure to Evaluate the Capacity of a Permanent Tunnel Lining
In this paper, in addition to the linear analysis used for typical tunnels, nonlinear seismic analysis of a tunnel has been investigated using pseudo-static method and a damaged concrete behavior model introduced in ABAQUS® software. The simulations were carried out under three conditions, free field, ovaling and racking, at two hazardous earthquake levels according to an Operation Design Earthquake (ODE) and a Maximum Design Earthquake (MDE). Then, the structural capacity curve and the behavior factor for the final tunnel lining were obtained. In order to extend the studies as well as to verify the pseudo-static analyses, seven nonlinear dynamic analyses compatible with the site under MDE conditions have been performed. The results showed that the tunnel lining procedure created limited tensile cracks under compression. At the bottom corners of the tunnel structure, the resultant stresses in the tunnel lining under two earthquakes caused failure and created tensile cracks. Therefore, it was necessary to reinforce the lining at corners. Comparison between different nonlinear time history seismic analysis and pseudo-static methods indicated that the pseudo-static methods resulted in 10–30% less acceleration than the average results obtained from time history analysis.
- Open Access
Optimized Alkali-Activated Slag-Based Concrete Reinforced with Recycled Tire Steel Fiber
This study employed Taguchi-Grey relational analysis to optimize the influences of binder content, the molarity of sodium hydroxide (SH) solution, alkaline solution to binder content (Al/Bi) ratio, water to alkali-activated solids (W/S) ratio, and sodium silicate to sodium hydroxide solution (SS/SH) ratio on the workability, setting time, and compressive strength of alkali-activated slag-based concrete (AASC). Then, the recycled tire steel fibers (RTSF) were introduced into the optimized mixture in different dosages, and the physical and mechanical properties of fiber-reinforced AASC (FR-AASC) were evaluated. RTSF inclusion negatively affected the workability and increased the density while slightly reducing the water absorption. Additionally, the compressive strength and flexural behavior of FR-AASC improved by increasing the RTSF content. The analysis of images taken from flexural specimens through the Digital Image Correlation technique (DIC) revealed that higher RTSF dosage caused a curved macro crack with several branches alongside, leading to a better post-cracking performance in terms of strength and toughness.
Open AccessOptimized Alkali-Activated Slag-Based Concrete Reinforced with Recycled Tire Steel Fiber
This study employed Taguchi-Grey relational analysis to optimize the influences of binder content, the molarity of sodium hydroxide (SH) solution, alkaline solution to binder content (Al/Bi) ratio, water to alkali-activated solids (W/S) ratio, and sodium silicate to sodium hydroxide solution (SS/SH) ratio on the workability, setting time, and compressive strength of alkali-activated slag-based concrete (AASC). Then, the recycled tire steel fibers (RTSF) were introduced into the optimized mixture in different dosages, and the physical and mechanical properties of fiber-reinforced AASC (FR-AASC) were evaluated. RTSF inclusion negatively affected the workability and increased the density while slightly reducing the water absorption. Additionally, the compressive strength and flexural behavior of FR-AASC improved by increasing the RTSF content. The analysis of images taken from flexural specimens through the Digital Image Correlation technique (DIC) revealed that higher RTSF dosage caused a curved macro crack with several branches alongside, leading to a better post-cracking performance in terms of strength and toughness.
- Open Access
Experimental Investigation on the Mechanical Characteristics of Cement-Based Mortar Containing Nano-Silica, Micro-Silica, and PVA Fiber
This paper investigates bending and compressive strengths as mechanical characteristics of cement-based repair mortar containing nano-silica (NS) and micro-silica (SF) as cement replacements particles and polyvinyl alcohol (PVA) fibers. The mentioned materials were added to the mortar in three different conditions, including single (just one material), binary (mixture of two admixtures), and ternary (mixture of all three admixtures) modes. The use of PVA fibers, nano-silica and micro-silica in the triple combination of a cement-based mortar is the primary objective of the current research. In total, 28 mix designs with various percentages of particles and fiber were employed in the current study, and 112 different specimens were prepared to conduct the experimental research. The compressive and flexural strength results have been selected as the criteria for obtaining the optimum mix design for each condition. In order to specify the mechanical characteristics of specimens, a compressive test was carried out according to ACI 318, and the three-point bending test was utilized according to BS EN 1015-11. The results obtained from this study show that the mixture containing 10% silica fume (SF10) can be considered the optimum mix design for the single-mode condition. For such a mix design, a flexural strength increase of 27% and a compressive strength improvement of 48% were determined in comparison to the reference mixture design. The mixture containing nano-silica at 2% and silica fume at 8% (NS2SF8) was the optimum mix design in the binary mode condition. With the current mix design, a flexural strength improvement of 24% and a compressive strength increase of 49% in a 28-day specimen were recorded. Finally, under the ternary mode condition, a flexural strength enhancement of 3.5% and a compressive strength improvement of 4.6% were obtained. Additionally, the mixture design containing a PVA content of 0.75% and an SF content of 10% (PVA0.75SF10) was considered optimum.
Open AccessExperimental Investigation on the Mechanical Characteristics of Cement-Based Mortar Containing Nano-Silica, Micro-Silica, and PVA Fiber
This paper investigates bending and compressive strengths as mechanical characteristics of cement-based repair mortar containing nano-silica (NS) and micro-silica (SF) as cement replacements particles and polyvinyl alcohol (PVA) fibers. The mentioned materials were added to the mortar in three different conditions, including single (just one material), binary (mixture of two admixtures), and ternary (mixture of all three admixtures) modes. The use of PVA fibers, nano-silica and micro-silica in the triple combination of a cement-based mortar is the primary objective of the current research. In total, 28 mix designs with various percentages of particles and fiber were employed in the current study, and 112 different specimens were prepared to conduct the experimental research. The compressive and flexural strength results have been selected as the criteria for obtaining the optimum mix design for each condition. In order to specify the mechanical characteristics of specimens, a compressive test was carried out according to ACI 318, and the three-point bending test was utilized according to BS EN 1015-11. The results obtained from this study show that the mixture containing 10% silica fume (SF10) can be considered the optimum mix design for the single-mode condition. For such a mix design, a flexural strength increase of 27% and a compressive strength improvement of 48% were determined in comparison to the reference mixture design. The mixture containing nano-silica at 2% and silica fume at 8% (NS2SF8) was the optimum mix design in the binary mode condition. With the current mix design, a flexural strength improvement of 24% and a compressive strength increase of 49% in a 28-day specimen were recorded. Finally, under the ternary mode condition, a flexural strength enhancement of 3.5% and a compressive strength improvement of 4.6% were obtained. Additionally, the mixture design containing a PVA content of 0.75% and an SF content of 10% (PVA0.75SF10) was considered optimum.
- 21 July 2022
- Published by Elsevier in Structures
- Vol. 43, 1230-1258
SMA-based self-centering eccentrically braced frame with vertical link member
- 21 July 2022
- Published by Elsevier in Structures
- Vol. 43, 1230-1258
SMA-based self-centering eccentrically braced frame with vertical link member
- 1 October 2021
- Published by Elsevier in Structures
- Vol. 33, 2019-2035
Introducing and numerical study of an innovative rotational damper with replaceable hourglass steel pins
- 1 October 2021
- Published by Elsevier in Structures
- Vol. 33, 2019-2035
Introducing and numerical study of an innovative rotational damper with replaceable hourglass steel pins
- Open Access
- 10 February 2018
- Published by Springer Nature in International Journal of Advanced Structural Engineering
- Vol. 10 (1) , 17-28
Assessment of the behavior of reinforced concrete beams retrofitted with pre-stressed CFPR subjected to cyclic loading
- 10 February 2018
- Published by Springer Nature in International Journal of Advanced Structural Engineering
- Vol. 10 (1) , 17-28
Open AccessAssessment of the behavior of reinforced concrete beams retrofitted with pre-stressed CFPR subjected to cyclic loading