Melih Cemal Kuşhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Melih Cemal Kuşhan has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Selim Gürgen
Eskisehir Osmangazi University
5 shared publications - Mohammad Rauf Sheikhi
Central South University
3 shared publications - Atanur Teoman
Eskişehir Osmangazi Üniversitesi
2 shared publications - Engin Göde
STM Savunma Teknol Muhendislik & Ticaret AS, Ankara, Turkiye
2 shared publications - Kürşat Tonbul
Savunma Sanayii Başkanlığı
2 shared publications - Abdullah Sert
Eskisehir Osmangazi University
1 shared publication
Latest Publications
- Open Access
- 28 February 2024
- Published by Journal of Aviation Research, Maltepe University in Journal of Aviation Research
- Vol. 6 (1) , 53-88
Global Navigation Satellite System (GNSS) Independent Navigation for Unmanned Aerial Vehicles (UAV)
The ability of Unmanned Aerial Vehicles (UAV) to perform autonomous navigation depends on the accurate determination of their positions provided by the Global Navigation Satellite System (GNSS). For position determination and environmental orientation during flight, UAVs are usually equipped with electronic equipment such as GNSS, Inertial Measurement Unit (IMU), gyroscope and accelerometer. However, the GNSS signal may be lost or distorted due to poor weather, obstacles or terrain, the unfavorable position of satellites, spoofing and jamming. In such cases of GNSS signal loss or deterioration, the IMU alone becomes unable to provide reliable UAV location information. Especially in cases where there is not enough visibility and the UAV cannot be brought to the take-off point by manual operation, the loss of the GNSS signal causes great losses. In this paper, GNSS independent flight and navigation studies are included. It is seen that the use of hybrid navigation solutions has great importance in GNSS independent UAV flights.
- 28 February 2024
- Published by Journal of Aviation Research, Maltepe University in Journal of Aviation Research
- Vol. 6 (1) , 53-88
Open AccessGlobal Navigation Satellite System (GNSS) Independent Navigation for Unmanned Aerial Vehicles (UAV)
The ability of Unmanned Aerial Vehicles (UAV) to perform autonomous navigation depends on the accurate determination of their positions provided by the Global Navigation Satellite System (GNSS). For position determination and environmental orientation during flight, UAVs are usually equipped with electronic equipment such as GNSS, Inertial Measurement Unit (IMU), gyroscope and accelerometer. However, the GNSS signal may be lost or distorted due to poor weather, obstacles or terrain, the unfavorable position of satellites, spoofing and jamming. In such cases of GNSS signal loss or deterioration, the IMU alone becomes unable to provide reliable UAV location information. Especially in cases where there is not enough visibility and the UAV cannot be brought to the take-off point by manual operation, the loss of the GNSS signal causes great losses. In this paper, GNSS independent flight and navigation studies are included. It is seen that the use of hybrid navigation solutions has great importance in GNSS independent UAV flights.
- 9 November 2023
- Published by Springer Nature
- p. 1-5
Cork Composites in Aerospace Applications
- 11 October 2023
- Published by Springer Nature
- p. 41-45
Deceleration Behavior of Super-Lightweight XPS Foams: Number of Layers Effect
- 11 October 2023
- Published by Springer Nature
- p. 41-45
Deceleration Behavior of Super-Lightweight XPS Foams: Number of Layers Effect
- 30 August 2023
- Published by Elsevier in Composite Structures
- Vol. 324, 117520
Design of smart sandwich structures enhanced by multi-functional shear thickening fluids (M−STFs): Anti-vibration and electrical conductivity
- 30 August 2023
- Published by Elsevier in Composite Structures
- Vol. 324, 117520
Design of smart sandwich structures enhanced by multi-functional shear thickening fluids (M−STFs): Anti-vibration and electrical conductivity
- 15 May 2023
- Published by Turkish National Defense University in Savunma Bilimleri Dergisi
SİVİL (GİZLİ ZIRHLI) ARAÇ ZIRHLAMA VE SERAMİK KOMPOZİT ZIRH UYGULAMALARI
Bu bildiride, sivil araç zırhlaması üzerine yapılan araştırmalar ve bu alanda kullanılmak üzere tasarlanan seramik kompozit bir zırhın balistik test sonuçları sunulmuştur. Günümüzün farklı mühimmat tehdit seviyelerine karşı askeri araçlarda olduğu gibi sivil araçlarda da zırhlama çok önemli bir konu haline gelmiştir. Ayrıca ağırlığın çok önemli bir tasarım kriteri olması nedeniyle hafif zırh sistemlerine olan talep de artmaktadır. Ağırlık, aracın yakıt tüketimini, motor gücünü ve ilgili diğer sistem gereksinimlerini artırır ve manevra kabiliyetini azaltır. Çalışmada sunulan bağımsız zırh, sivil araçlarda kullanılmak üzere geliştirilmiş ve zırh panelinin ağırlık kazancı, Ultra Yüksek Sertlikli (UHH) zırh çelikleri (Armox 600T ve Armox Advance) ile karşılaştırılmıştır. Geliştirilen zırh, darbe yüzünde alümina (Al2O3) seramik karolardan ve son katmanda Ultra Yüksek Moleküler Ağırlıklı Polietilen (UHWMPE) kompozit destek plakasından oluşmaktadır ve 7.62 mm x 51 M61 AP mermiye karşı test edilmiştir. Hafif zırh panelinin beş atıştan sonra yapısal bütünlüğünü koruduğu gözlemlenmiştir. Geliştirilen zırh panelinin sivil zırhlı araçlar için 7.62 mm zırh delici mühimmatlara karşı hafif ve uygun maliyetli çözüm sağladığı değerlendirilmektedir.
- 15 May 2023
- Published by Turkish National Defense University in Savunma Bilimleri Dergisi
SİVİL (GİZLİ ZIRHLI) ARAÇ ZIRHLAMA VE SERAMİK KOMPOZİT ZIRH UYGULAMALARI
Bu bildiride, sivil araç zırhlaması üzerine yapılan araştırmalar ve bu alanda kullanılmak üzere tasarlanan seramik kompozit bir zırhın balistik test sonuçları sunulmuştur. Günümüzün farklı mühimmat tehdit seviyelerine karşı askeri araçlarda olduğu gibi sivil araçlarda da zırhlama çok önemli bir konu haline gelmiştir. Ayrıca ağırlığın çok önemli bir tasarım kriteri olması nedeniyle hafif zırh sistemlerine olan talep de artmaktadır. Ağırlık, aracın yakıt tüketimini, motor gücünü ve ilgili diğer sistem gereksinimlerini artırır ve manevra kabiliyetini azaltır. Çalışmada sunulan bağımsız zırh, sivil araçlarda kullanılmak üzere geliştirilmiş ve zırh panelinin ağırlık kazancı, Ultra Yüksek Sertlikli (UHH) zırh çelikleri (Armox 600T ve Armox Advance) ile karşılaştırılmıştır. Geliştirilen zırh, darbe yüzünde alümina (Al2O3) seramik karolardan ve son katmanda Ultra Yüksek Moleküler Ağırlıklı Polietilen (UHWMPE) kompozit destek plakasından oluşmaktadır ve 7.62 mm x 51 M61 AP mermiye karşı test edilmiştir. Hafif zırh panelinin beş atıştan sonra yapısal bütünlüğünü koruduğu gözlemlenmiştir. Geliştirilen zırh panelinin sivil zırhlı araçlar için 7.62 mm zırh delici mühimmatlara karşı hafif ve uygun maliyetli çözüm sağladığı değerlendirilmektedir.
- 3 November 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (16)
An investigation on wear behavior of UHMWPE/carbide composites at elevated temperatures
Ultra‐high molecular weight polyethylene (UHMWPE) is extensively used in frictional applications due to its advanced wear resistance. This advanced polymer is reinforced with hard particulate fillers for further developments against wear conditions. Since elevated temperatures prevail in the service conditions, wear behavior of UHMWPE composites is an important issue for the engineering applications. In the present work, UHMWPE‐based composites including silicon carbide (SiC) fillers were fabricated in a compression molding chamber. In the specimen preparation stage, molding pressure, filler amount, and filler particle size were varied to investigate the influence of these variables. Upon deciding the optimum parameters from the wear tests conducted at room temperature, the wear experiments were repeated for the optimum specimen at elevated temperatures, such as 40 and 60°C. According to the results, the wear behavior of the SiC/UHMWPE composites is heavily changed by the effect of elevated temperature. Adhesive effect is pronounced at elevated temperatures while the wear characteristics possess the abrasive effect in the sliding path. In addition, the composites exhibit an accelerated material loss as temperature increases during the frictional system.
- 3 November 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (16)
An investigation on wear behavior of UHMWPE/carbide composites at elevated temperatures
Ultra‐high molecular weight polyethylene (UHMWPE) is extensively used in frictional applications due to its advanced wear resistance. This advanced polymer is reinforced with hard particulate fillers for further developments against wear conditions. Since elevated temperatures prevail in the service conditions, wear behavior of UHMWPE composites is an important issue for the engineering applications. In the present work, UHMWPE‐based composites including silicon carbide (SiC) fillers were fabricated in a compression molding chamber. In the specimen preparation stage, molding pressure, filler amount, and filler particle size were varied to investigate the influence of these variables. Upon deciding the optimum parameters from the wear tests conducted at room temperature, the wear experiments were repeated for the optimum specimen at elevated temperatures, such as 40 and 60°C. According to the results, the wear behavior of the SiC/UHMWPE composites is heavily changed by the effect of elevated temperature. Adhesive effect is pronounced at elevated temperatures while the wear characteristics possess the abrasive effect in the sliding path. In addition, the composites exhibit an accelerated material loss as temperature increases during the frictional system.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 11
An Investigation on Surface Roughness and Tool Wear in Turning Operation of Inconel 718
This paper investigates the influences of three different input parameters, such as feed rate, insert nose radius, and insert coating methods, in the turning operation of Inconel 718. The coating methods were selected as medium temperature chemical vapor deposition (MT-CVD) and physical vapor deposition (PVD) and in addition to coating methods, the role of various coating materials was discussed since the inserts were coated with multi-layers of TiCN/Al2O3/TiN and single-layer of TiAlN on carbide substrates. The results were discussed in terms of wear behavior of cutting tools and surface quality of the workpiece, which is indicated by surface roughness. A full factorial experimental design was employed in the present work and the results were evaluated using main effects plots. Furthermore, the analysis of variance (ANOVA) method was applied to specify both reactive and non-reactive effects of experimental parameter reactions. The results showed that surface roughness is reduced using low feed rates and large nosed inserts in the operations. Furthermore, TiAlN-coated inserts with PVD method provided better surface finish than with MT-CVD method. It was also found that surface roughness increases as the wear rate of inserts increases.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 11
Open AccessAn Investigation on Surface Roughness and Tool Wear in Turning Operation of Inconel 718
This paper investigates the influences of three different input parameters, such as feed rate, insert nose radius, and insert coating methods, in the turning operation of Inconel 718. The coating methods were selected as medium temperature chemical vapor deposition (MT-CVD) and physical vapor deposition (PVD) and in addition to coating methods, the role of various coating materials was discussed since the inserts were coated with multi-layers of TiCN/Al2O3/TiN and single-layer of TiAlN on carbide substrates. The results were discussed in terms of wear behavior of cutting tools and surface quality of the workpiece, which is indicated by surface roughness. A full factorial experimental design was employed in the present work and the results were evaluated using main effects plots. Furthermore, the analysis of variance (ANOVA) method was applied to specify both reactive and non-reactive effects of experimental parameter reactions. The results showed that surface roughness is reduced using low feed rates and large nosed inserts in the operations. Furthermore, TiAlN-coated inserts with PVD method provided better surface finish than with MT-CVD method. It was also found that surface roughness increases as the wear rate of inserts increases.
- 12 August 2008
- Published by Elsevier in Engineering Failure Analysis
- Vol. 16 (4) , 1203-1207
Effect of dent geometry on fatigue life of aircraft structural cylinder part
- 12 August 2008
- Published by Elsevier in Engineering Failure Analysis
- Vol. 16 (4) , 1203-1207
Effect of dent geometry on fatigue life of aircraft structural cylinder part