KZKevin Zaseck

Kevin Zaseck

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kevin Zaseck has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Closed-Loop Control of Combustion Initiation and Combustion Duration

    by Bryan P. Maldonado, Kevin Zaseck, Eiki Kitagawa, Anna G. Stefanopoulou

    When high levels of cooled external exhaust gas recirculation (EGR) are used to increase engine efficiency, the laminar flame speed during the flame initiation period is reduced and the combustion duration is elongated. The reduction in flame propagation speed together with the increase in cycle-to-cycle variability makes the combustion process prone to failure of flame initiation (misfire) or slow burning rates. A highly visited operating speed/load point is used to investigate the feedback control of spark advance (SA) and EGR valve. A decentralized proportional-integral (PI) controller and a centralized linear quadratic Gaussian (LQG) controller are designed to maintain a desired combustion initiation and duration that indirectly ensures a proper flame kernel initiation and flame propagation. A simple control-oriented combustion model is derived from system identification to perform simulation and linear analysis of the closed-loop (CL) system. Experimental validation of the controllers shows that the LQG performs better in transients and produces the least amount of cycle-to-cycle variability in CL operation. Analysis of the linearized system in frequency domain shows that a multivariable architecture is required to handle the input-output coupling efficiently. Sensitivity analysis of PI and LQG controllers under gain variability is reported to guide the tuning process, which also influences the cycle-to-cycle variability. The two-input two-output controllers designed in this paper are compared with a single-input single-output (SISO) controller designed to only adjust SA for the maximum brake torque. When the EGR valve is adjusted based on a lookup table, uncertainty in the EGR-rate will directly affect the combustion duration for which the SISO controller alone cannot handle. In conclusion, a coordinated spark and EGR controller based on the measured combustion features is deemed to be required for combustion control under diluted conditions.


  • Combustion shaping using multivariable feedback control

    by Bryan P. Maldonado, Huan Lian, Jason B. Martz, Anna G. Stefanopoulou, Kevin Zaseck, Eiki Kitagawa


  • Prediction of Flame Burning Velocity at Early Flame Development Time With High Exhaust Gas Recirculation and Spark Advance

    by H. Lian, J. B. Martz, B. P. Maldonado, A. G. Stefanopoulou, K. Zaseck, J. Wilkie, O. Nitulescu, M. Ehara

    Diluting spark-ignited (SI) stoichiometric combustion engines with excess residual gas improves thermal efficiency and allows the spark to be advanced toward maximum brake torque (MBT) timing. However, flame propagation rates decrease and misfires can occur at high exhaust gas recirculation (EGR) conditions and advanced spark, limiting the maximum level of charge dilution and its benefits. The misfire limits are often determined for a specific engine from extensive experiments covering a large range of speed, torque, and actuator settings. To extend the benefits of dilute combustion while at the misfire limit, it is essential to define a parameterizable, physics-based model capable of predicting the misfire limits, with cycle to cycle varied flame burning velocity as operating conditions change based on the driver demand. A cycle-averaged model is the first step in this process. The current work describes a model of cycle-averaged laminar flame burning velocity within the early flame development period of 0–3% mass fraction burned. A flame curvature correction method is used to account for both the effect of flame stretch and ignition characteristics, in a variable volume engine system. Comparison of the predicted and the measured flame velocity was performed using a spark plug with fiber optical access. The comparison at a small set of spark and EGR settings at fixed load and speed, shows an agreement within 30% of uncertainty, while 20% uncertainty equals ± one standard deviation over 2000 cycles.


  • Stability, Control, and Constraint Enforcement of Piston Motion in a Hydraulic Free-Piston Engine

    by Kevin Zaseck, Matthew Brusstar, Ilya Kolmanovsky

    A free-piston engine (FPE) requires stabilizing feedback control to manage piston motion and ensure safe operation. A high-fidelity model, which simulates the FPE behavior by combining dynamic, thermodynamic, and hydraulic submodels, is exploited as an engine surrogate for control development. A control-oriented model implicitly describes the FPE piston turnaround position using energy balance principles for an idealized Otto cycle. Local eigenvalues of the control-oriented model suggest that the FPE system is open-loop unstable. The control system relies on dynamic inversion and state feedback to stabilize the plant and track a target piston turnaround position. A robust reference governor is introduced to manage load changes, such that the piston position does not violate constraints, even in the presence of parameter uncertainty. In high-fidelity simulations, the reference governor constrains piston turnaround position to ±0.5 mm of the target during a load change.


  • Rate-Based Model Predictive Controller for Diesel Engine Air Path: Design and Experimental Evaluation

    by Mike Huang, Kevin Zaseck, Ken Butts, Ilya Kolmanovsky

    This paper presents the development and results of rate-based model predictive control (RB-MPC) for a diesel engine air path. The objective is to regulate the intake manifold pressure and the exhaust gas recirculation (EGR) flow estimate to the specified set-points by coordinated control of the Variable Geometry Turbine (VGT), EGR valve, and EGR throttle actuators. We present steps by which we arrive at a controller that has low computational complexity, good tracking performance, and capability to enforce multiple constraints. Through the employed strategies, the need to cover the operating range with multiple linear models and to use a complicated switching controller structure is avoided. Simulation and experimental results are presented that demonstrate the ability of RB-MPC to follow specified set-points while satisfying state and control constraints throughout the engine operating range.