I. Lappo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
I. Lappo has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Yurii Dobryshkin
State Scientific Research Institute of Armament and Military Equipment Testing and Certification, Ukraine
7 shared publications - M. Herashchenko6 shared publications
- О.в. Червотока
State Scientific Research Institute of Armament and Military Equipment Testing and Certification, Cherkasy, Ukraine
6 shared publications - S. Prykhodko4 shared publications
- Oleksii Zhurakhov3 shared publications
- Vladlen Kuznetsov
Державний науково-дослідний інститут випробувань і сертифікації озброєння та військової техніки
3 shared publications
Latest Publications
- Open Access
- 9 October 2024
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 20 (3) , 76-83
GENERAL RECOMMENDATIONS FOR THE SEARCH AND DETECTION OF EXPLOSIVE ORDNANCE IN THE CONDITIONS OF HIGH CONTAMINATION OF THE AREA WITH METAL FRAGMENTS
Currently, the enemy is using new mining tactics, when other sources of danger are additionally installed during mining, in particular with anti-personnel mines (APMs). This leads to accidents among sappers during operational demining. Therefore, there is an urgent problem of determining the procedure for searching for UXOs when the area is highly contaminated with metal fragments. An analysis of specialized literature has shown that the problem of searching, detecting and identifying UXOs both on land and in the water is the subject of close attention by both military specialists and researchers. Considerable attention has been paid to the testing and evaluation of metal detectors. However, the issue of searching for UXOs in highly contaminated areas with metal fragments, especially in areas of combat operations, has not been covered. The purpose of this article is to determine the procedure for organizing and conducting search and detection operations for UXOs in a highly contaminated area with nearby mines and metal fragments. At the same time, the risk of an emergency should be minimized. In this study, taking into account the fact of an increase in the number of accidents among deminers, it is proposed to adhere to the following recommendations when searching for and detecting UXOs in a highly contaminated area with metal fragments every working day before the start of the search for UXO, calibrate the metal detector to ensure confidence in the ability of the metal detector to distinguish between signals from the source of the hazard and nearby targets. Record the calibration of each metal detector in the calibration log; it is recommended to carry out work on the search for UXO using a metal detector within a 1-meter wide clearance strip using a base rail; it is recommended to mark the source of the hazardous signal along the edge of the search element of the metal detector, rather than determine the center of the signal; when searching for UXOs with high contamination of the area with metal fragments, it is recommended not to use probes, but to excavate the soil around the marked UXO using a shovel (scraper).
- 9 October 2024
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 20 (3) , 76-83
Open AccessGENERAL RECOMMENDATIONS FOR THE SEARCH AND DETECTION OF EXPLOSIVE ORDNANCE IN THE CONDITIONS OF HIGH CONTAMINATION OF THE AREA WITH METAL FRAGMENTS
Currently, the enemy is using new mining tactics, when other sources of danger are additionally installed during mining, in particular with anti-personnel mines (APMs). This leads to accidents among sappers during operational demining. Therefore, there is an urgent problem of determining the procedure for searching for UXOs when the area is highly contaminated with metal fragments. An analysis of specialized literature has shown that the problem of searching, detecting and identifying UXOs both on land and in the water is the subject of close attention by both military specialists and researchers. Considerable attention has been paid to the testing and evaluation of metal detectors. However, the issue of searching for UXOs in highly contaminated areas with metal fragments, especially in areas of combat operations, has not been covered. The purpose of this article is to determine the procedure for organizing and conducting search and detection operations for UXOs in a highly contaminated area with nearby mines and metal fragments. At the same time, the risk of an emergency should be minimized. In this study, taking into account the fact of an increase in the number of accidents among deminers, it is proposed to adhere to the following recommendations when searching for and detecting UXOs in a highly contaminated area with metal fragments every working day before the start of the search for UXO, calibrate the metal detector to ensure confidence in the ability of the metal detector to distinguish between signals from the source of the hazard and nearby targets. Record the calibration of each metal detector in the calibration log; it is recommended to carry out work on the search for UXO using a metal detector within a 1-meter wide clearance strip using a base rail; it is recommended to mark the source of the hazardous signal along the edge of the search element of the metal detector, rather than determine the center of the signal; when searching for UXOs with high contamination of the area with metal fragments, it is recommended not to use probes, but to excavate the soil around the marked UXO using a shovel (scraper).
- Open Access
- 1 December 2023
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 18 (4) , 55-64
INTERNATIONAL EXPERIENCE IN TESTING DEMINING MACHINES. THE POSSIBILITY OF INTRODUCING THEM INTO THE NATIONAL SYSTEM OF MINE ACTION
To ensure an independent assessment of the applicability, safety and effectiveness of mechanical equipment used during the survey and demining of a contaminated area, it is necessary to test and evaluate its conformity. This makes it possible to assess the capabilities and potential of new technologies and confirm the performance and operational characteristics of the equipment used. To implement the above, it is necessary to clearly define the requirements that mechanical equipment in the field of humanitarian demining must meet; regulatory documents for which testing and conformity assessment must be carried out, i.e., a methodological apparatus for testing and assessing mechanical equipment and tools for it must be developed. The results of the analysis of scientific publications indicate that the issue of determining the requirements for mechanical equipment for humanitarian demining has not been studied, and there is no methodological apparatus for assessing the conformity of equipment and conducting tests. The purpose of the article is to investigate the international and regional experience of humanitarian demining in the context of regulatory and methodological support for determining the requirements for mechanical equipment and methods for their confirmation, as well as the possibility of their adaptation to the national mine action system. It has been established that the following factors should be taken into consideration when developing and using mechanical demining equipment: the specific hazard of ERW, the minimum distance from the explosion site; simplicity of design and operation; maintainability and stability of equipment in the area of operations; ability to transport to the demining site independently; adaptability of mechanical means to different terrain conditions; ability to achieve the required demining depth (15 cm) for Ukraine. It is recommended to take into account the practical experience and regulatory framework of competent international organizations for humanitarian demining to develop a regulatory and methodological apparatus for testing and assessing the conformity of mechanical demining equipment. В статті розглянуто проблемні питання нормативно-методичного забезпечення випробувань та оцінювання відповідності механічного обладнання розмінування у сфері гуманітарного розмінування. Визначено основні критерії оцінювання машин розмінування на основі аналізу досвіду компетентних міжнародних організацій у сфері гуманітарного розмінування. Встановлено, що під час розробки і використання механічного обладнання розмінування необхідно враховувати наступні фактори: конкретну небезпеку ВНП, мінімальну відстань від місця вибуху; простоту конструкції і експлуатації; ремонтопридатність і стійкість обладнання в районі проведення операцій; здатність до самостійного транспортування на місце розмінування; пристосованість механічних засобів до різних умов місцевості; здатність досягати необхідної глибини розмінування.
- 1 December 2023
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 18 (4) , 55-64
Open AccessINTERNATIONAL EXPERIENCE IN TESTING DEMINING MACHINES. THE POSSIBILITY OF INTRODUCING THEM INTO THE NATIONAL SYSTEM OF MINE ACTION
To ensure an independent assessment of the applicability, safety and effectiveness of mechanical equipment used during the survey and demining of a contaminated area, it is necessary to test and evaluate its conformity. This makes it possible to assess the capabilities and potential of new technologies and confirm the performance and operational characteristics of the equipment used. To implement the above, it is necessary to clearly define the requirements that mechanical equipment in the field of humanitarian demining must meet; regulatory documents for which testing and conformity assessment must be carried out, i.e., a methodological apparatus for testing and assessing mechanical equipment and tools for it must be developed. The results of the analysis of scientific publications indicate that the issue of determining the requirements for mechanical equipment for humanitarian demining has not been studied, and there is no methodological apparatus for assessing the conformity of equipment and conducting tests. The purpose of the article is to investigate the international and regional experience of humanitarian demining in the context of regulatory and methodological support for determining the requirements for mechanical equipment and methods for their confirmation, as well as the possibility of their adaptation to the national mine action system. It has been established that the following factors should be taken into consideration when developing and using mechanical demining equipment: the specific hazard of ERW, the minimum distance from the explosion site; simplicity of design and operation; maintainability and stability of equipment in the area of operations; ability to transport to the demining site independently; adaptability of mechanical means to different terrain conditions; ability to achieve the required demining depth (15 cm) for Ukraine. It is recommended to take into account the practical experience and regulatory framework of competent international organizations for humanitarian demining to develop a regulatory and methodological apparatus for testing and assessing the conformity of mechanical demining equipment. В статті розглянуто проблемні питання нормативно-методичного забезпечення випробувань та оцінювання відповідності механічного обладнання розмінування у сфері гуманітарного розмінування. Визначено основні критерії оцінювання машин розмінування на основі аналізу досвіду компетентних міжнародних організацій у сфері гуманітарного розмінування. Встановлено, що під час розробки і використання механічного обладнання розмінування необхідно враховувати наступні фактори: конкретну небезпеку ВНП, мінімальну відстань від місця вибуху; простоту конструкції і експлуатації; ремонтопридатність і стійкість обладнання в районі проведення операцій; здатність до самостійного транспортування на місце розмінування; пристосованість механічних засобів до різних умов місцевості; здатність досягати необхідної глибини розмінування.
- Open Access
- 12 April 2023
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 15 (1) , 74-80
MINE ACTION CENTER: MAIN ASPECTS OF ACTIVITY AND DEVELOPMENT PROSPECTS
Statement of the Problem. Ukraine is one of the ten countries with the most explosive contaminated territory, and this situation tends to worsen due to the scale of military operations and the use of so-called “mine warfare” tactics. Therefore, the сreation of an effective mine action system, taking into account the needs of safe demining of the territory of Ukraine from explosive objects, is a priority task at the national level. Analysis of recent research and publications. The analysis of professional literature has shown that the issues of creating an effective mine action system, improving the regulatory framework based on international experience, problems and ways to solve humanitarian demining, and the impact of explosive hazards on the environment are in the focus of attention of the scientific community. The issue of development and improvement of the mine action system has become even more urgent and requires further development taking into account the principles of international humanitarian law and measures to minimize the danger caused by explosive hazards. The purpose of the article is to study the activities and identify promising ways of development of the Center for Mine Action in the conditions of the legal regime of martial law. In Ukraine there is an effective mine action system with clear subordination to the National Mine Action Agency. In order to implement mine action measures in practice, the Mine Action Center was established, which has an effective mine clearance quality management system, including certification of mine action operators (Certification Agency) and control of demining quality (Inspection Agency). Within the framework of international cooperation, joint projects are implemented with foreign countries, international organizations and institutions, in which the Mine Action Center is an active participant. A system of training and advanced training of the Mine Action Center’s personnel involved in demining has been implemented. Promising ways of developing mine action within the competence of the Mine Action Center include the following: expanding the scope of accreditation of the Certification Agency; improvement of normative and legal acts of mine countermeasures (amendments to existing ones and creation of new ones); increasing the effectiveness of mine action tasks by conducting applied and fundamental research within the authority of the scientific research laboratory.
- 12 April 2023
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 15 (1) , 74-80
Open AccessMINE ACTION CENTER: MAIN ASPECTS OF ACTIVITY AND DEVELOPMENT PROSPECTS
Statement of the Problem. Ukraine is one of the ten countries with the most explosive contaminated territory, and this situation tends to worsen due to the scale of military operations and the use of so-called “mine warfare” tactics. Therefore, the сreation of an effective mine action system, taking into account the needs of safe demining of the territory of Ukraine from explosive objects, is a priority task at the national level. Analysis of recent research and publications. The analysis of professional literature has shown that the issues of creating an effective mine action system, improving the regulatory framework based on international experience, problems and ways to solve humanitarian demining, and the impact of explosive hazards on the environment are in the focus of attention of the scientific community. The issue of development and improvement of the mine action system has become even more urgent and requires further development taking into account the principles of international humanitarian law and measures to minimize the danger caused by explosive hazards. The purpose of the article is to study the activities and identify promising ways of development of the Center for Mine Action in the conditions of the legal regime of martial law. In Ukraine there is an effective mine action system with clear subordination to the National Mine Action Agency. In order to implement mine action measures in practice, the Mine Action Center was established, which has an effective mine clearance quality management system, including certification of mine action operators (Certification Agency) and control of demining quality (Inspection Agency). Within the framework of international cooperation, joint projects are implemented with foreign countries, international organizations and institutions, in which the Mine Action Center is an active participant. A system of training and advanced training of the Mine Action Center’s personnel involved in demining has been implemented. Promising ways of developing mine action within the competence of the Mine Action Center include the following: expanding the scope of accreditation of the Certification Agency; improvement of normative and legal acts of mine countermeasures (amendments to existing ones and creation of new ones); increasing the effectiveness of mine action tasks by conducting applied and fundamental research within the authority of the scientific research laboratory.
- Open Access
- 30 December 2022
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 14 (4) , 110-117
BASIC PRINCIPLES OF IMPROVING THE ACCURACY OF TEMPERATURE MEASUREMENT BY NON-CONTACT METHODS
Statement of the Problem. The development of methods and means for measuring temperature and improving the accuracy of measurement, as well as the study of thermal processes of temperature distribution is a promising and urgent scientific task. Analysis of recent research and publications. The analysis of professional literature has shown that at present the problem of studying the temperature distribution in a particular field of activity has already been studied to some extent. However, the practical implementation of methods and means to improve the accuracy of temperature measurement is not sufficiently developed. The purpose of the article is to determine the fundamental factors by analyzing the theoretical and experimental material related to improving the accuracy of temperature measurement and the study of thermal processes during temperature measurements by non-contact method. Non-contact methods allow temperature measurement at a distance without direct contact with the object of measurement and are based on measuring the surface temperature of the object using infrared devices: pyrometers and thermal imagers. A pyrometer allows to measure the temperature of a local point of the measurement object, a thermal imager is used to visualize temperature fields. It is established that pyrometric measurement methods are based on determining the parameters of thermal radiation of the object without disturbing its temperature field. High accuracy of measurement results is achieved due to individual selection of filters and narrow spectral range. Conclusions. The analysis made it possible to note that the main factors that affect the accuracy of the measurement results by the pyrometer include the following: the change in the emissivity of the measurement object depending on the wavelength in the spectral range and on the temperature in the measurement range; the presence of radiation absorption in the medium between the pyrometer and the measurement object (the presence of a significant amount of dust, smoke or steam in the air in front of the sample reduces the accuracy of the measurement); geometric parameters of the field of view (visibility index) of the pyrometer Taking into account these factors in practice will increase the accuracy of the temperature measurement results by the pyrometer.
- 30 December 2022
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- Vol. 14 (4) , 110-117
Open AccessBASIC PRINCIPLES OF IMPROVING THE ACCURACY OF TEMPERATURE MEASUREMENT BY NON-CONTACT METHODS
Statement of the Problem. The development of methods and means for measuring temperature and improving the accuracy of measurement, as well as the study of thermal processes of temperature distribution is a promising and urgent scientific task. Analysis of recent research and publications. The analysis of professional literature has shown that at present the problem of studying the temperature distribution in a particular field of activity has already been studied to some extent. However, the practical implementation of methods and means to improve the accuracy of temperature measurement is not sufficiently developed. The purpose of the article is to determine the fundamental factors by analyzing the theoretical and experimental material related to improving the accuracy of temperature measurement and the study of thermal processes during temperature measurements by non-contact method. Non-contact methods allow temperature measurement at a distance without direct contact with the object of measurement and are based on measuring the surface temperature of the object using infrared devices: pyrometers and thermal imagers. A pyrometer allows to measure the temperature of a local point of the measurement object, a thermal imager is used to visualize temperature fields. It is established that pyrometric measurement methods are based on determining the parameters of thermal radiation of the object without disturbing its temperature field. High accuracy of measurement results is achieved due to individual selection of filters and narrow spectral range. Conclusions. The analysis made it possible to note that the main factors that affect the accuracy of the measurement results by the pyrometer include the following: the change in the emissivity of the measurement object depending on the wavelength in the spectral range and on the temperature in the measurement range; the presence of radiation absorption in the medium between the pyrometer and the measurement object (the presence of a significant amount of dust, smoke or steam in the air in front of the sample reduces the accuracy of the measurement); geometric parameters of the field of view (visibility index) of the pyrometer Taking into account these factors in practice will increase the accuracy of the temperature measurement results by the pyrometer.
- 5 July 2022
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 12,p. 77-83
FEATURES OF LABORATORY TESTING OF ARMORED VEHICLES AND AUTOMOTIVE EQUIPMENT AGAINST EXTERNAL MECHANICAL AND CLIMATIC FACTORS
У статті проведено порівняння існуючих в Україні та в провідних країнах світу нормативних документів та методичний апарату проведення випробувань зразків бронетанкової та автомобільної техніки щодо впливу зовнішніх механічних і кліматичних факторів. Здійснено порівняння методів випробувань зразків бронетанкової та автомобільної техніки на вплив зовнішніх механічних і кліматичних факторів, а також визначено основні види випробувань. Практична реалізація отриманих в статті результатів полягає в можливості їх застосуванні під час розробки програм і методик лабораторних випробувань зразків бронетанкової та автомобільної техніки.
- 5 July 2022
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 12,p. 77-83
FEATURES OF LABORATORY TESTING OF ARMORED VEHICLES AND AUTOMOTIVE EQUIPMENT AGAINST EXTERNAL MECHANICAL AND CLIMATIC FACTORS
У статті проведено порівняння існуючих в Україні та в провідних країнах світу нормативних документів та методичний апарату проведення випробувань зразків бронетанкової та автомобільної техніки щодо впливу зовнішніх механічних і кліматичних факторів. Здійснено порівняння методів випробувань зразків бронетанкової та автомобільної техніки на вплив зовнішніх механічних і кліматичних факторів, а також визначено основні види випробувань. Практична реалізація отриманих в статті результатів полягає в можливості їх застосуванні під час розробки програм і методик лабораторних випробувань зразків бронетанкової та автомобільної техніки.
- Open Access
- 30 December 2021
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Visnyk NTUU KPI Seriia - Radiotekhnika Radioaparatobuduvannia
- No. 87,p. 14-21
Recommendations for Implementation of Data Flow Control Method Based on Different Priorities in Stationary Component of Communication System of Armed Forces of Ukraine
Relevance. The task of increasing the productivity of the communication system stationary component of the Armed Forces of Ukraine requires the introduction of appropriate new methods for controlling the data flow of different priorities, which should be further implemented in modern routing protocols in accordance with the concept of next generation networks.Method. The method of data flow control based on different priorities in the communication system stationary component of the Armed Forces of Ukraine is investigated. The aforementioned method consists of the following stages: monitoring and analysis of initial data; formation of the required parameters vector; formation of metrics for the use of network resources; statement of the mathematical optimization problem; solution of the optimization problem. Within the framework of the method, the coordinated solution of the problems of multipath routing and adaptive limitation of the flow rate at the border of the information and telecommunication network is provided on the basis of different priorities.Results. The method on a specific example of the network structure using the ''Optimization Toolbox'' of the Matlab software package is studied in the article. Practical recommendations are developed for the practical implementation of the method in the stationary component of the communication system of the Armed Forces of Ukraine. Conclusions. Based on the simulation results, it is established that the method implementation in modern technological solutions increases the productivity of the information and telecommunication network by an average of (10-20) %, and the quality of service with the probability of packet delivery by (1-3) %. The proposed method meets the requirements of the Traffic Engineering data flow control concept. It is noted that in order to validate the adequacy and reliability of the improved method in the future, it is necessary to conduct a full-scale experiment on real network equipment.
- 30 December 2021
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Visnyk NTUU KPI Seriia - Radiotekhnika Radioaparatobuduvannia
- No. 87,p. 14-21
Open AccessRecommendations for Implementation of Data Flow Control Method Based on Different Priorities in Stationary Component of Communication System of Armed Forces of Ukraine
Relevance. The task of increasing the productivity of the communication system stationary component of the Armed Forces of Ukraine requires the introduction of appropriate new methods for controlling the data flow of different priorities, which should be further implemented in modern routing protocols in accordance with the concept of next generation networks.Method. The method of data flow control based on different priorities in the communication system stationary component of the Armed Forces of Ukraine is investigated. The aforementioned method consists of the following stages: monitoring and analysis of initial data; formation of the required parameters vector; formation of metrics for the use of network resources; statement of the mathematical optimization problem; solution of the optimization problem. Within the framework of the method, the coordinated solution of the problems of multipath routing and adaptive limitation of the flow rate at the border of the information and telecommunication network is provided on the basis of different priorities.Results. The method on a specific example of the network structure using the ''Optimization Toolbox'' of the Matlab software package is studied in the article. Practical recommendations are developed for the practical implementation of the method in the stationary component of the communication system of the Armed Forces of Ukraine. Conclusions. Based on the simulation results, it is established that the method implementation in modern technological solutions increases the productivity of the information and telecommunication network by an average of (10-20) %, and the quality of service with the probability of packet delivery by (1-3) %. The proposed method meets the requirements of the Traffic Engineering data flow control concept. It is noted that in order to validate the adequacy and reliability of the improved method in the future, it is necessary to conduct a full-scale experiment on real network equipment.
- Open Access
- 3 December 2021
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 9,p. 79-87
ANALYSIS OF THE PROVISIONS OF NATIONAL STANDARDS FOR TESTING ARMAMENT AND MILITARY EQUIPMENT ON THE IPMACT OF MECHANICAL FACTORS
З метою забезпечення сумісності Збройних Сил України та армій країн-членів НАТО вносяться зміни до національного законодавства України стосовно створення механізму впровадження стандартів НАТО або їх положень у Збройних Силах України. Для забезпечення нормативного супроводження життєвого циклу озброєння та військової техніки здійснюються заходи щодо повного переходу оборонно-промислового комплексу України на застосування у виробництві міжнародних, європейських стандартів та стандартів НАТО. У 2021 році прийняті національні стандарти ДСТУ STANAG 4370:2021, гармонізовані зі стандартами НАТО STANAG 4370, які регламентують організацію та проведення випробувань зразків озброєння та військової техніки на вплив зовнішніх факторів. Оскільки дані стандарти прийняті мовою оригіналу, а в Україні відсутня практика розповсюдження та використання англомовних нормативних документів, постає проблема однозначного тлумачення змісту даних стандартів всіма заінтересованими сторонами: виробниками продукції, випробувальними лабораторіями, науковими установами тощо. Метою статті є проведення аналізу основних положень національних стандартів стосовно умов та методів випробувань на вплив механічних факторів з метою імплементації їх у систему випробувань зразків озброєння та військової техніки. Під час проведення дослідження були застосовані загальнонаукові методи обробки та систематизації інформації, зокрема, системний аналіз та синтез організаційно-технічних систем. У зв‟язку із скасуванням комплексу державних військових стандартів “Апаратура, прилади, пристрої та обладнання військового призначення. Загальні технічні вимоги, методи контролю та випробувань” виникла нагальна проблема нормативного забезпечення організації та проведення випробувань озброєння та військової техніки. Визначено, що одним з основних напрямів вирішення проблеми нормативного забезпечення організації та проведення випробувань зразків озброєння та військової техніки є прийняття міжнародних військових стандартів в якості державних. Проведено аналіз основних положень стандартів, які забезпечують організацію та проведення випробувань військової техніки на вплив механічних факторів, розглянута структура та зміст даних стандартів.
- 3 December 2021
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 9,p. 79-87
Open AccessANALYSIS OF THE PROVISIONS OF NATIONAL STANDARDS FOR TESTING ARMAMENT AND MILITARY EQUIPMENT ON THE IPMACT OF MECHANICAL FACTORS
З метою забезпечення сумісності Збройних Сил України та армій країн-членів НАТО вносяться зміни до національного законодавства України стосовно створення механізму впровадження стандартів НАТО або їх положень у Збройних Силах України. Для забезпечення нормативного супроводження життєвого циклу озброєння та військової техніки здійснюються заходи щодо повного переходу оборонно-промислового комплексу України на застосування у виробництві міжнародних, європейських стандартів та стандартів НАТО. У 2021 році прийняті національні стандарти ДСТУ STANAG 4370:2021, гармонізовані зі стандартами НАТО STANAG 4370, які регламентують організацію та проведення випробувань зразків озброєння та військової техніки на вплив зовнішніх факторів. Оскільки дані стандарти прийняті мовою оригіналу, а в Україні відсутня практика розповсюдження та використання англомовних нормативних документів, постає проблема однозначного тлумачення змісту даних стандартів всіма заінтересованими сторонами: виробниками продукції, випробувальними лабораторіями, науковими установами тощо. Метою статті є проведення аналізу основних положень національних стандартів стосовно умов та методів випробувань на вплив механічних факторів з метою імплементації їх у систему випробувань зразків озброєння та військової техніки. Під час проведення дослідження були застосовані загальнонаукові методи обробки та систематизації інформації, зокрема, системний аналіз та синтез організаційно-технічних систем. У зв‟язку із скасуванням комплексу державних військових стандартів “Апаратура, прилади, пристрої та обладнання військового призначення. Загальні технічні вимоги, методи контролю та випробувань” виникла нагальна проблема нормативного забезпечення організації та проведення випробувань озброєння та військової техніки. Визначено, що одним з основних напрямів вирішення проблеми нормативного забезпечення організації та проведення випробувань зразків озброєння та військової техніки є прийняття міжнародних військових стандартів в якості державних. Проведено аналіз основних положень стандартів, які забезпечують організацію та проведення випробувань військової техніки на вплив механічних факторів, розглянута структура та зміст даних стандартів.
- 29 June 2021
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 8,p. 56-62
RECOMMENDATIONS FOR EQUIPPING THE PROVING GROUND F OR TESTING ARMORED AND AUTOMOTIVE VEHICLES
Постановка проблеми. Оснащення Збройних Сил України новітніми зразками озброєння та військової техніки, в тому числі бронетанковою та автомобільною технікою, призводить до необхідності створення відповідного випробувального полігону: розбудови об’єктів інфраструктури, оснащення засобами та обладнанням для лабораторних випробувань а також засобами для контролю працездатності та визначення технічного стану озброєння та військової техніки. Аналіз останніх досліджень і публікацій. В існуючих публікаціях, на жаль, відсутні рекомендації щодо оснащення полігону для випробувань бронетанкової та автомобільної техніки. У статті визначенні основні завдання полігону, запропоновано доцільний склад його елементів та загальні вимоги до них, а також пропозиції щодо його оснащення лабораторно-випробувальним обладнанням. Для вирішення зазначених завдань до складу полігону повинні входити такі основні об’єкти та системи: ділянка з перевірки бронетанкової та автомобільної техніки для експериментального визначення показників прохідності, маневреності, динамічних якостей, транспортабельності зразків БТАТ, а також для проведення випробувань зразків на стійкість до впливу зовнішніх факторів навколишнього середовища; майданчик для перевірки зразків бронетанкової та автомобільної техніки на живучість; комплекс доріг загального користування, спеціальних випробувальних доріг; спеціальні об’єкти для розміщення лабораторно- випробувального обладнання; інженерні мережі для забезпечення випробувань та життєдіяльності (електропостачання, водопостачання та інше); системи метрологічного, метеорологічного, протипожежного та медичного забезпечення, забезпечення екологічної безпеки; система захисту від зброї масового ураження та біологічного захисту, система охорони. Висновки. Створення полігону для випробувань бронетанкової та автомобільної техніки дозволить забезпечити: набуття спроможності випробувальної бази ЗС України щодо оцінки перспективних зразків бронетанкової та автомобільної техніки; підвищення досягнутого рівня контролю за технічним станом озброєння та військової техніки під час проведення випробувань; оцінку результатів заходів бойової підготовки з бойовим застосуванням озброєння та військової техніки; акредитацію полігону для випробувань озброєння та військової техніки у національних та міжнародних органах оцінки відповідності та сертифікації на право проведення робіт відповідно стандартів НАТО.
- 29 June 2021
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 8,p. 56-62
RECOMMENDATIONS FOR EQUIPPING THE PROVING GROUND F OR TESTING ARMORED AND AUTOMOTIVE VEHICLES
Постановка проблеми. Оснащення Збройних Сил України новітніми зразками озброєння та військової техніки, в тому числі бронетанковою та автомобільною технікою, призводить до необхідності створення відповідного випробувального полігону: розбудови об’єктів інфраструктури, оснащення засобами та обладнанням для лабораторних випробувань а також засобами для контролю працездатності та визначення технічного стану озброєння та військової техніки. Аналіз останніх досліджень і публікацій. В існуючих публікаціях, на жаль, відсутні рекомендації щодо оснащення полігону для випробувань бронетанкової та автомобільної техніки. У статті визначенні основні завдання полігону, запропоновано доцільний склад його елементів та загальні вимоги до них, а також пропозиції щодо його оснащення лабораторно-випробувальним обладнанням. Для вирішення зазначених завдань до складу полігону повинні входити такі основні об’єкти та системи: ділянка з перевірки бронетанкової та автомобільної техніки для експериментального визначення показників прохідності, маневреності, динамічних якостей, транспортабельності зразків БТАТ, а також для проведення випробувань зразків на стійкість до впливу зовнішніх факторів навколишнього середовища; майданчик для перевірки зразків бронетанкової та автомобільної техніки на живучість; комплекс доріг загального користування, спеціальних випробувальних доріг; спеціальні об’єкти для розміщення лабораторно- випробувального обладнання; інженерні мережі для забезпечення випробувань та життєдіяльності (електропостачання, водопостачання та інше); системи метрологічного, метеорологічного, протипожежного та медичного забезпечення, забезпечення екологічної безпеки; система захисту від зброї масового ураження та біологічного захисту, система охорони. Висновки. Створення полігону для випробувань бронетанкової та автомобільної техніки дозволить забезпечити: набуття спроможності випробувальної бази ЗС України щодо оцінки перспективних зразків бронетанкової та автомобільної техніки; підвищення досягнутого рівня контролю за технічним станом озброєння та військової техніки під час проведення випробувань; оцінку результатів заходів бойової підготовки з бойовим застосуванням озброєння та військової техніки; акредитацію полігону для випробувань озброєння та військової техніки у національних та міжнародних органах оцінки відповідності та сертифікації на право проведення робіт відповідно стандартів НАТО.
- 21 May 2021
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 7,p. 49-60
ANALYSIS OF NATO STANDARDS PERTAINING TO THE CONFORMANCE ASSESSMENT OF PIECES OF ARMAMENT AND MILITARY EQUIPMENT WITH THE REQUIREMENTS OF RESISTANCE TO CLIMATIC FACTORS
Стратегічний курс на інтеграцію України до європейського економічного простору передбачає впровадження відповідних стандартів якості у виробництво вітчизняної продукції, у тому числі й оборонного призначення. Керівництвом держави задекларовано перехід українського оборонно-промислового комплексу на стандарти Євросоюзу та НАТО до 2022 року. Впровадження даних стандартів повинно забезпечити сумісність Збройних Сил України та армій країн – членів НАТО. Оскільки розробка високоточних зразків озброєння та військової техніки призводить до необхідності створення нового покоління спеціалізованих систем контролю їх характеристик та параметрів під час проведення випробувань, першочерговою необхідністю є вдосконалення системи випробувань, нормативною основою якої є система стандартів. Як наслідок, в першу чергу потребують перегляду стандарти, які регламентують підготовку та проведення випробувань нових та модернізованих зразків озброєння та військової техніки. З метою активізації робіт з перегляду стандартів, а також забезпечення нормативного супроводження життєвого циклу озброєння та військової техніки до повного переходу на застосування у виробництві міжнародних, європейських стандартів та стандартів НАТО вносяться зміни до національного законодавства України з метою створення механізму впровадження стандартів НАТО або їх положень у Збройних Силах України. Під час проведення дослідження були застосовані загальнонаукові методи обробки та систематизації інформації, зокрема системний аналіз та синтез організаційно-технічних систем. У зв’язку із скасуванням державних військових стандартів системи ГОСТ В, які встановлювали рівень показників якості та склад, послідовність, загальні вимоги до проведення випробувань апаратури, приладів, пристроїв та обладнання військового призначення, виникла нагальна проблема нормативного забезпечення організації та проведення випробувань озброєння та військової техніки. Визначено, що одним з основних напрямів вирішення проблеми нормативного забезпечення організації та проведення випробувань зразків озброєння та військової техніки є прийняття міжнародних військових стандартів в якості державних. Проведено аналіз основних положень стандартів, які забезпечують організацію та проведення випробувань військової техніки на вплив кліматичних факторів, розглянута структура та зміст даних стандартів.
- 21 May 2021
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 7,p. 49-60
ANALYSIS OF NATO STANDARDS PERTAINING TO THE CONFORMANCE ASSESSMENT OF PIECES OF ARMAMENT AND MILITARY EQUIPMENT WITH THE REQUIREMENTS OF RESISTANCE TO CLIMATIC FACTORS
Стратегічний курс на інтеграцію України до європейського економічного простору передбачає впровадження відповідних стандартів якості у виробництво вітчизняної продукції, у тому числі й оборонного призначення. Керівництвом держави задекларовано перехід українського оборонно-промислового комплексу на стандарти Євросоюзу та НАТО до 2022 року. Впровадження даних стандартів повинно забезпечити сумісність Збройних Сил України та армій країн – членів НАТО. Оскільки розробка високоточних зразків озброєння та військової техніки призводить до необхідності створення нового покоління спеціалізованих систем контролю їх характеристик та параметрів під час проведення випробувань, першочерговою необхідністю є вдосконалення системи випробувань, нормативною основою якої є система стандартів. Як наслідок, в першу чергу потребують перегляду стандарти, які регламентують підготовку та проведення випробувань нових та модернізованих зразків озброєння та військової техніки. З метою активізації робіт з перегляду стандартів, а також забезпечення нормативного супроводження життєвого циклу озброєння та військової техніки до повного переходу на застосування у виробництві міжнародних, європейських стандартів та стандартів НАТО вносяться зміни до національного законодавства України з метою створення механізму впровадження стандартів НАТО або їх положень у Збройних Силах України. Під час проведення дослідження були застосовані загальнонаукові методи обробки та систематизації інформації, зокрема системний аналіз та синтез організаційно-технічних систем. У зв’язку із скасуванням державних військових стандартів системи ГОСТ В, які встановлювали рівень показників якості та склад, послідовність, загальні вимоги до проведення випробувань апаратури, приладів, пристроїв та обладнання військового призначення, виникла нагальна проблема нормативного забезпечення організації та проведення випробувань озброєння та військової техніки. Визначено, що одним з основних напрямів вирішення проблеми нормативного забезпечення організації та проведення випробувань зразків озброєння та військової техніки є прийняття міжнародних військових стандартів в якості державних. Проведено аналіз основних положень стандартів, які забезпечують організацію та проведення випробувань військової техніки на вплив кліматичних факторів, розглянута структура та зміст даних стандартів.
- 30 December 2020
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 6,p. 81-86
DEVELOPMENT OF THE GENERAL REQUIREMENTS FOR THERMAL PRESSURE CHAMBER
Inspection of armament and military equipment (AME) for the quality of manufacture and purpose tasks performance is carried out exclusively through testing. Tasks of conducting tests within the framework of ensuring the implementation of State programs for equipping the Armed Forces of Ukraine with modern armament and military equipment require proper instrumentation of the laboratory and test base of the Armed Forces of Ukraine, which is necessary to determine during tests numerical indicators of technical and operational characteristics in accordance with requirements of state standards parallel to standards of world’s major economies to evaluate new, upgraded armament, armament with service life extension and procured armament. During the study, general scientific methods of information processing and systematization were used, in particular system analysis and synthesis of organizational and technical systems. The purpose of the article is to improve the quality of testing of new and modernized pieces of AME by developing general requirements for a thermal pressure chamber. A study was conducted to substantiate the composition of the thermal pressure chamber, its main tasks, objects of action, capabilities, conditions of application, requirements for interaction with control systems or other objects with which the system is combined. Based on the analysis, the article proposes general requirements for a thermal pressure chamber, which will improve the quality of testing of new and upgraded pieces of AME; reduce material and technical expenditures and reduce the time of AME testing.
- 30 December 2020
- Published by State Scientific Research Institute of Armament and Military Equipment Testing and Certification in Наукові праці Державного науково-дослідного інституту випробувань і сертифікації озброєння та військової техніки
- No. 6,p. 81-86
DEVELOPMENT OF THE GENERAL REQUIREMENTS FOR THERMAL PRESSURE CHAMBER
Inspection of armament and military equipment (AME) for the quality of manufacture and purpose tasks performance is carried out exclusively through testing. Tasks of conducting tests within the framework of ensuring the implementation of State programs for equipping the Armed Forces of Ukraine with modern armament and military equipment require proper instrumentation of the laboratory and test base of the Armed Forces of Ukraine, which is necessary to determine during tests numerical indicators of technical and operational characteristics in accordance with requirements of state standards parallel to standards of world’s major economies to evaluate new, upgraded armament, armament with service life extension and procured armament. During the study, general scientific methods of information processing and systematization were used, in particular system analysis and synthesis of organizational and technical systems. The purpose of the article is to improve the quality of testing of new and modernized pieces of AME by developing general requirements for a thermal pressure chamber. A study was conducted to substantiate the composition of the thermal pressure chamber, its main tasks, objects of action, capabilities, conditions of application, requirements for interaction with control systems or other objects with which the system is combined. Based on the analysis, the article proposes general requirements for a thermal pressure chamber, which will improve the quality of testing of new and upgraded pieces of AME; reduce material and technical expenditures and reduce the time of AME testing.