Viktor Kis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Viktor Kis has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Anatoliy Paliy
National Scientific Center "Institute of Experimental and Clinical Veterinary Medicine
4 shared publications - Andriy Paliy
State Biotechnological University, Ukraine
4 shared publications - Elchyn Aliiev
Dnipro State Agrarian and Economic University
4 shared publications - Iruna Levchenko
Sumy National Agrarian University, Ukraine
3 shared publications - Andriy Milenin
State Biotechnological University
1 shared publication - Artur Levkin
Державний біотехнологічний університет
1 shared publication
Latest Publications
- Open Access
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (120)) , 62-69
Increasing energy efficiency and enabling the process of vacuum mode stabilization during the operation of milking equipment
A scientific hypothesis has been put forward, according to which an increase in the efficiency of using a vacuum system of milking equipment with an upper milk line with mechanical pulsators can be achieved by predicting its residual resource. As well as with the subsequent planning of maintenance and the identification of patterns and dependences characterizing these processes. As a result of experimental studies of changes in the technical and technological parameters of the vacuum system of milking equipment with an upper milk line with mechanical pulsators, the theoretical dependences obtained with their correlation coefficient r=0.971–0.972 were empirically confirmed. Namely, the magnitude of the working vacuum, the pulsation rate, the ratio of pulsations, and the tension force of the nipple rubber, depending on the time of operation. It was established that after 175 hours of operation of the milking stationary installation, the value of the working vacuum decreased by 4 %, the pulsation frequency – 14 %, the ratio of pulsations – 16 %, and the tension force of nipple rubber – 21 %. On the basis of the obtained dependences included in the procedure for forecasting the resource of the vacuum system of milk-milking equipment with an upper milk line with mechanical pulsators, the software package «Alt viewer 1.0» was developed. It is designed to display and automatically process the measurement results of the technical and technological parameters of milking equipment using the designed Tester of milking machines, v.2.0. The software performs the following main functions: reading the measurement results from the memory card, decoding them, displaying them in tabular and graphical forms. As well as the calculation of the parameters of pulsations and the formation of a report, forecasting the resource of the nodes of the vacuum system. The program also provides for the storage of information on the calibration coefficients of pressure sensors, air flow meter, as well as the frequency of polling sensors when measuring pulsations and fluctuations of the working vacuum
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (120)) , 62-69
Open AccessIncreasing energy efficiency and enabling the process of vacuum mode stabilization during the operation of milking equipment
A scientific hypothesis has been put forward, according to which an increase in the efficiency of using a vacuum system of milking equipment with an upper milk line with mechanical pulsators can be achieved by predicting its residual resource. As well as with the subsequent planning of maintenance and the identification of patterns and dependences characterizing these processes. As a result of experimental studies of changes in the technical and technological parameters of the vacuum system of milking equipment with an upper milk line with mechanical pulsators, the theoretical dependences obtained with their correlation coefficient r=0.971–0.972 were empirically confirmed. Namely, the magnitude of the working vacuum, the pulsation rate, the ratio of pulsations, and the tension force of the nipple rubber, depending on the time of operation. It was established that after 175 hours of operation of the milking stationary installation, the value of the working vacuum decreased by 4 %, the pulsation frequency – 14 %, the ratio of pulsations – 16 %, and the tension force of nipple rubber – 21 %. On the basis of the obtained dependences included in the procedure for forecasting the resource of the vacuum system of milk-milking equipment with an upper milk line with mechanical pulsators, the software package «Alt viewer 1.0» was developed. It is designed to display and automatically process the measurement results of the technical and technological parameters of milking equipment using the designed Tester of milking machines, v.2.0. The software performs the following main functions: reading the measurement results from the memory card, decoding them, displaying them in tabular and graphical forms. As well as the calculation of the parameters of pulsations and the formation of a report, forecasting the resource of the nodes of the vacuum system. The program also provides for the storage of information on the calibration coefficients of pressure sensors, air flow meter, as well as the frequency of polling sensors when measuring pulsations and fluctuations of the working vacuum
- Open Access
- 31 August 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (1 (118)) , 80-89
Justifying parameters for the automatic servo control system of a rotary plate vacuum pump in the milking machine
The scientific task to improve energy efficiency and ensure the process of vacuum regime stabilization in the operation of milking machines has been solved. A mathematical model of the process of functioning of the servo control system of a rotary plate vacuum pump was built; the numerical modeling of its workflow was carried out. This paper reports the results of experimental studies on the influence of the regime parameters of the rotary plate vacuum pump on the efficiency of its operation, as well as the results of experimental research on the servo control system for the rotary plate vacuum pump. The operational process of the rotary plate vacuum pump HB-1200 for a milking machine was investigated. The influence of mode parameters (rotor speed n and vacuum pressure P) on the performance of the vacuum pump, Qa, vacuum pressure fluctuation, ΔP, and the power consumption of the vacuum pump drive, Np, has been determined. The servo control system of the rotary plate vacuum pump was experimentally investigated based on the developed algorithms of its operation. In a generally accepted algorithm, vacuum fluctuation increases with increasing an airflow rate: at ΔQa=45 l/min – ΔP=2.3 kPa; at ΔQa=90 l/min – ΔP=4.6 kPa; at ΔQa=135 l/min – ΔP=6.4 kPa. Unlike the generally accepted one, the developed algorithm enables a stable vacuum mode with the largest vacuum fluctuation being ΔP=2.4 kPa. For the first time, the functional dependence of the influence of the regime parameters of the rotary plate vacuum pump with its automatic servo control system on the stability of the vacuum regime of a milk-vacuum system in the milking machine was established. The results can be applied when improving milking machines in terms of ensuring the stabilization process of the vacuum regime.
- 31 August 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (1 (118)) , 80-89
Open AccessJustifying parameters for the automatic servo control system of a rotary plate vacuum pump in the milking machine
The scientific task to improve energy efficiency and ensure the process of vacuum regime stabilization in the operation of milking machines has been solved. A mathematical model of the process of functioning of the servo control system of a rotary plate vacuum pump was built; the numerical modeling of its workflow was carried out. This paper reports the results of experimental studies on the influence of the regime parameters of the rotary plate vacuum pump on the efficiency of its operation, as well as the results of experimental research on the servo control system for the rotary plate vacuum pump. The operational process of the rotary plate vacuum pump HB-1200 for a milking machine was investigated. The influence of mode parameters (rotor speed n and vacuum pressure P) on the performance of the vacuum pump, Qa, vacuum pressure fluctuation, ΔP, and the power consumption of the vacuum pump drive, Np, has been determined. The servo control system of the rotary plate vacuum pump was experimentally investigated based on the developed algorithms of its operation. In a generally accepted algorithm, vacuum fluctuation increases with increasing an airflow rate: at ΔQa=45 l/min – ΔP=2.3 kPa; at ΔQa=90 l/min – ΔP=4.6 kPa; at ΔQa=135 l/min – ΔP=6.4 kPa. Unlike the generally accepted one, the developed algorithm enables a stable vacuum mode with the largest vacuum fluctuation being ΔP=2.4 kPa. For the first time, the functional dependence of the influence of the regime parameters of the rotary plate vacuum pump with its automatic servo control system on the stability of the vacuum regime of a milk-vacuum system in the milking machine was established. The results can be applied when improving milking machines in terms of ensuring the stabilization process of the vacuum regime.
- Open Access
- 28 April 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (116)) , 35-46
Establishing an interconnection between the technical and technological parameters of milking equipment based on the movement of a milk-air mixture in a milking machine
Machine milking is one of the main technological processes in the dairy industry whose efficiency level largely affects cattle breeding in general. The key role, in this case, belongs to milking equipment. The design and use of technical means of milking are associated with certain difficulties related to the imperfection of milk discharge. Therefore, the current study is due to the need to investigate the process of moving the milk mixture in a milking machine. A physical-mathematical model of the process of moving the two-phase milk-air mixture along the milk-conducting line of a milking machine has been built. The mathematical model relates the value of the fluctuating of vacuummetric pressure ΔP, the rate of milk discharge QM, the pulse rate ζ, and the value of working vacuummetric pressure P. It was found that in the milk-conducting system with the upper milk pipeline there is a large fluctuation of vacuummetric pressure ΔP=1.02–4.69 kPa, which exceeds the regulated value (2.5 kPa). In a milk-conducting system with a lower milk pipeline, the vacuummetric pressure fluctuation is ΔP=0.59–1.84 kPa. The patterns of change in the value of working pressure P and the frequency of pulsations ζ in the milking machines of simultaneous and pair action depending on the rate of milk discharge from the udder have been determined. It is established that the maximum deviation of the value of fluctuation of vacuummetric pressure ΔP between the experimental and theoretical data within a predefined range of factors is 0.81 kPa. The correlation coefficient is 0.92, which indicates the adequacy of the constructed models. Owing to this, the task of the rational choice of milking equipment is resolved
- 28 April 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (116)) , 35-46
Open AccessEstablishing an interconnection between the technical and technological parameters of milking equipment based on the movement of a milk-air mixture in a milking machine
Machine milking is one of the main technological processes in the dairy industry whose efficiency level largely affects cattle breeding in general. The key role, in this case, belongs to milking equipment. The design and use of technical means of milking are associated with certain difficulties related to the imperfection of milk discharge. Therefore, the current study is due to the need to investigate the process of moving the milk mixture in a milking machine. A physical-mathematical model of the process of moving the two-phase milk-air mixture along the milk-conducting line of a milking machine has been built. The mathematical model relates the value of the fluctuating of vacuummetric pressure ΔP, the rate of milk discharge QM, the pulse rate ζ, and the value of working vacuummetric pressure P. It was found that in the milk-conducting system with the upper milk pipeline there is a large fluctuation of vacuummetric pressure ΔP=1.02–4.69 kPa, which exceeds the regulated value (2.5 kPa). In a milk-conducting system with a lower milk pipeline, the vacuummetric pressure fluctuation is ΔP=0.59–1.84 kPa. The patterns of change in the value of working pressure P and the frequency of pulsations ζ in the milking machines of simultaneous and pair action depending on the rate of milk discharge from the udder have been determined. It is established that the maximum deviation of the value of fluctuation of vacuummetric pressure ΔP between the experimental and theoretical data within a predefined range of factors is 0.81 kPa. The correlation coefficient is 0.92, which indicates the adequacy of the constructed models. Owing to this, the task of the rational choice of milking equipment is resolved
- Open Access
- 24 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (1 (115)) , 44-55
Establishing the influence of technical and technological parameters of milking equipment on the efficiency of machine milking
One of the tasks that imply increasing the milk productivity of cows is to create optimal maintenance conditions that ensure the increased use of the genetic potential of cattle based on the implementation of engineering and technological solutions. A mathematical model has been built that links the technical and technological parameters of the vacuum system of milking equipment, namely, the value of the working vacuum P, the pulsation frequency n, the ratio of pulsation cycles, and the tension strength of milking rubber FH to cows’ milk yield rate V. The range of milking plant operating parameters for milking in the milk line has been determined, at which the milk yield rate is maximum: P=52 kPa, n=57.6–58.8 min–1, δ=0.59–0.64, FH=59.3–60.4 H. Under these parameters, the milk yield rate is V=1.48–1.53 l/min. The results of the multifactor experiment have helped construct an adequate mathematical model of the second order, which confirms the theoretical dependence of the influence of the technical and technological parameters of the vacuum system of milking equipment on milk yield rate and the air flow of the milking machine. Analysis of the mathematical model has made it possible to establish the rational structural and technological parameters for the vacuum system of a milking machine: the value of the working vacuum, P=50.6 kPa; pulsation frequency, n=55.9 min–1, the ratio of pulsation cycles and the tension force of milking rubber FH=64.8 H. Under these parameters, the milk yield rate is maximum: V=1.47–1.52 l/min; the air flow consumption of the milking machine is Q=2.19 m3/h. The mathematical model built fully reveals the influence of technical and technological parameters of milking equipment on the efficiency of machine milking. Owing to this, the issue related to the rational choice of equipment is resolved.
- 24 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (1 (115)) , 44-55
Open AccessEstablishing the influence of technical and technological parameters of milking equipment on the efficiency of machine milking
One of the tasks that imply increasing the milk productivity of cows is to create optimal maintenance conditions that ensure the increased use of the genetic potential of cattle based on the implementation of engineering and technological solutions. A mathematical model has been built that links the technical and technological parameters of the vacuum system of milking equipment, namely, the value of the working vacuum P, the pulsation frequency n, the ratio of pulsation cycles, and the tension strength of milking rubber FH to cows’ milk yield rate V. The range of milking plant operating parameters for milking in the milk line has been determined, at which the milk yield rate is maximum: P=52 kPa, n=57.6–58.8 min–1, δ=0.59–0.64, FH=59.3–60.4 H. Under these parameters, the milk yield rate is V=1.48–1.53 l/min. The results of the multifactor experiment have helped construct an adequate mathematical model of the second order, which confirms the theoretical dependence of the influence of the technical and technological parameters of the vacuum system of milking equipment on milk yield rate and the air flow of the milking machine. Analysis of the mathematical model has made it possible to establish the rational structural and technological parameters for the vacuum system of a milking machine: the value of the working vacuum, P=50.6 kPa; pulsation frequency, n=55.9 min–1, the ratio of pulsation cycles and the tension force of milking rubber FH=64.8 H. Under these parameters, the milk yield rate is maximum: V=1.47–1.52 l/min; the air flow consumption of the milking machine is Q=2.19 m3/h. The mathematical model built fully reveals the influence of technical and technological parameters of milking equipment on the efficiency of machine milking. Owing to this, the issue related to the rational choice of equipment is resolved.
- Open Access
- 1 January 2014
- Published by Wiley in BioMed Research International
- Vol. 2014, 1-19
Atg6/UVRAG/Vps34-Containing Lipid Kinase Complex Is Required for Receptor Downregulation through Endolysosomal Degradation and Epithelial Polarity duringDrosophilaWing Development
Atg6 (Beclin 1 in mammals) is a core component of the Vps34 PI3K (III) complex, which promotes multiple vesicle trafficking pathways. Atg6 and Vps34 form two distinct PI3K (III) complexes in yeast and mammalian cells, either with Atg14 or with UVRAG. The functions of these two complexes are not entirely clear, as both Atg14 and UVRAG have been suggested to regulate both endocytosis and autophagy. In this study, we performed a microscopic analysis of UVRAG, Atg14, or Atg6 loss-of-function cells in the developingDrosophilawing. Both autophagy and endocytosis are seriously impaired and defective endolysosomes accumulate upon loss of Atg6. We show that Atg6 is required for the downregulation of Notch and Wingless signaling pathways; thus it is essential for normal wing development. Moreover, the loss of Atg6 impairs cell polarity. Atg14 depletion results in autophagy defects with no effect on endocytosis or cell polarity, while the silencing of UVRAG phenocopies all but the autophagy defect of Atg6 depleted cells. Thus, our results indicate that the UVRAG-containing PI3K (III) complex is required for receptor downregulation through endolysosomal degradation and for the establishment of proper cell polarity in the developing wing, while the Atg14-containing complex is involved in autophagosome formation.
- 1 January 2014
- Published by Wiley in BioMed Research International
- Vol. 2014, 1-19
Open AccessAtg6/UVRAG/Vps34-Containing Lipid Kinase Complex Is Required for Receptor Downregulation through Endolysosomal Degradation and Epithelial Polarity duringDrosophilaWing Development
Atg6 (Beclin 1 in mammals) is a core component of the Vps34 PI3K (III) complex, which promotes multiple vesicle trafficking pathways. Atg6 and Vps34 form two distinct PI3K (III) complexes in yeast and mammalian cells, either with Atg14 or with UVRAG. The functions of these two complexes are not entirely clear, as both Atg14 and UVRAG have been suggested to regulate both endocytosis and autophagy. In this study, we performed a microscopic analysis of UVRAG, Atg14, or Atg6 loss-of-function cells in the developingDrosophilawing. Both autophagy and endocytosis are seriously impaired and defective endolysosomes accumulate upon loss of Atg6. We show that Atg6 is required for the downregulation of Notch and Wingless signaling pathways; thus it is essential for normal wing development. Moreover, the loss of Atg6 impairs cell polarity. Atg14 depletion results in autophagy defects with no effect on endocytosis or cell polarity, while the silencing of UVRAG phenocopies all but the autophagy defect of Atg6 depleted cells. Thus, our results indicate that the UVRAG-containing PI3K (III) complex is required for receptor downregulation through endolysosomal degradation and for the establishment of proper cell polarity in the developing wing, while the Atg14-containing complex is involved in autophagosome formation.