Hafiz Muhammad Awais Rashid
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hafiz Muhammad Awais Rashid has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Ali Murtaza Rasool
National Engineering Services Pakistan (NESPAK), Lahore, Pakistan
3 shared publications Atif Ismail
Energy Systems Engineering, University of Regina, Canada
2 shared publications- Mohsin Usman Qureshi
Sohar University
2 shared publications - Shahab Saqib
Department of Mining Engineering, University of Engineering & Technology Lahore, Lahore 54890, Pakistan
2 shared publications - Umer Waqas
University of Engineering & Technology
2 shared publications A. M. N. Alagiyawanna
University of Ruhuna
1 shared publication
Latest Publications
- 26 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Mining Sciences
- p. 391-407
A Field-Scale Investigation into the Strategic Location of Air Decks for Improved Blasting Performance
Airdeck blasting is a promising technique for improved blast efficiency, reducing explosive consumption, and enhancing fragmentation. Nevertheless, it lacks widespread adoption due to design guideline gaps and differing opinions on air deck placement. This study offers technical guidance based on field experiments to optimise air deck blasting. Full-scale blast experiments were conducted at four distinct limestone benches to evaluate the efficacy of air deck implementation. At Bench-1, experiments were performed using conventional blasting (with full-column charge) and air decks at three strategic air deck positions (i.e., top, mid, and bottom) within blast holes at a selected quarry site. For Benches 2 and 3, comparative fragmentation analyses were conducted between conventional blasts and those utilising air decks positioned in the middle of the explosive column. Furthermore, the impact of multiple mid-air decks within explosive columns was also evaluated at Bench-4. A comparison of blast fragmentation results revealed that fragments obtained through the air decking technique surpassed those from the full-column charge, regardless of air deck placement. Among the tested air deck positions, the single air deck positioned at the middle of the explosive column yielded superior fragmentation results than other locations. In addition, this technique showed a reduction in explosive charge, back break, and toe-related issues.
- 26 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Mining Sciences
- p. 391-407
A Field-Scale Investigation into the Strategic Location of Air Decks for Improved Blasting Performance
Airdeck blasting is a promising technique for improved blast efficiency, reducing explosive consumption, and enhancing fragmentation. Nevertheless, it lacks widespread adoption due to design guideline gaps and differing opinions on air deck placement. This study offers technical guidance based on field experiments to optimise air deck blasting. Full-scale blast experiments were conducted at four distinct limestone benches to evaluate the efficacy of air deck implementation. At Bench-1, experiments were performed using conventional blasting (with full-column charge) and air decks at three strategic air deck positions (i.e., top, mid, and bottom) within blast holes at a selected quarry site. For Benches 2 and 3, comparative fragmentation analyses were conducted between conventional blasts and those utilising air decks positioned in the middle of the explosive column. Furthermore, the impact of multiple mid-air decks within explosive columns was also evaluated at Bench-4. A comparison of blast fragmentation results revealed that fragments obtained through the air decking technique surpassed those from the full-column charge, regardless of air deck placement. Among the tested air deck positions, the single air deck positioned at the middle of the explosive column yielded superior fragmentation results than other locations. In addition, this technique showed a reduction in explosive charge, back break, and toe-related issues.
- Open Access
- 26 September 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 253
Evaluation of Strength Anisotropy in Foliated Metamorphic Rocks: A Review Focused on Microscopic Mechanisms
This review paper addresses the recent and past advancements in investigating the anisotropic behavior of foliated metamorphic rock strength subjected to uniaxial or triaxial compression loading, direct or indirect tensile loading, and shear loading. The experimental findings published in the literature show that the strength of foliated rocks is significantly affected by varying the angle β between weak planes and major principal stress. A higher value of strength is reported at β = 0° or 90°; whereas a low strength value is noted at intermediate angles between β = 0° and 90°. The strength anisotropy depends on the degree of schistosity or gneissosity, which is the result of the preferred arrangement of phyllosilicate minerals under differential pressures. The failure of foliated rocks starts at the microscopic scale because of the dislocation slip, plastic kinking, and fracturing in phyllosilicate minerals such as mica. Tensile wing cracks at the tip of the mica propagate parallel to the deviatoric stress. Then, intergranular and intragranular shear-tensile cracks coalesce and lead to rock failure. The weak planes’ orientation controls the mode of failure such that tensile splitting, slip failure, and shear failure across foliations are observed at β = 0°–30°, β = 30°–60°, β = 60°–90° respectively. In the past, several attempts have been made to formulate failure criteria to estimate rock strength using different mathematical and empirical approaches. Over the years, the trend has shifted towards discontinuum modeling to simulate rock failure processes and to solve problems from laboratory to upscaled levels.
- 26 September 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 253
Open AccessEvaluation of Strength Anisotropy in Foliated Metamorphic Rocks: A Review Focused on Microscopic Mechanisms
This review paper addresses the recent and past advancements in investigating the anisotropic behavior of foliated metamorphic rock strength subjected to uniaxial or triaxial compression loading, direct or indirect tensile loading, and shear loading. The experimental findings published in the literature show that the strength of foliated rocks is significantly affected by varying the angle β between weak planes and major principal stress. A higher value of strength is reported at β = 0° or 90°; whereas a low strength value is noted at intermediate angles between β = 0° and 90°. The strength anisotropy depends on the degree of schistosity or gneissosity, which is the result of the preferred arrangement of phyllosilicate minerals under differential pressures. The failure of foliated rocks starts at the microscopic scale because of the dislocation slip, plastic kinking, and fracturing in phyllosilicate minerals such as mica. Tensile wing cracks at the tip of the mica propagate parallel to the deviatoric stress. Then, intergranular and intragranular shear-tensile cracks coalesce and lead to rock failure. The weak planes’ orientation controls the mode of failure such that tensile splitting, slip failure, and shear failure across foliations are observed at β = 0°–30°, β = 30°–60°, β = 60°–90° respectively. In the past, several attempts have been made to formulate failure criteria to estimate rock strength using different mathematical and empirical approaches. Over the years, the trend has shifted towards discontinuum modeling to simulate rock failure processes and to solve problems from laboratory to upscaled levels.
- 21 October 2023
- Published by Elsevier in Geoenergy Science and Engineering
- Vol. 231
Statistical and machine learning hybridization for predicting shear wave velocity in tight sand reservoirs: A case study
- 21 October 2023
- Published by Elsevier in Geoenergy Science and Engineering
- Vol. 231
Statistical and machine learning hybridization for predicting shear wave velocity in tight sand reservoirs: A case study
- 6 December 2022
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 41 (2) , 1503-1519
Experimental Characterization-Based Machine Learning Modeling for the Estimation of Geotechnical Properties of Clay Liners
- 6 December 2022
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 41 (2) , 1503-1519
Experimental Characterization-Based Machine Learning Modeling for the Estimation of Geotechnical Properties of Clay Liners
- Open Access
- 7 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2752
Damage Characteristics of Thermally Deteriorated Carbonate Rocks: A Review
This review paper summarizes the recent and past experimental findings to evaluate the damage characteristics of carbonate rocks subjected to thermal treatment (20–1500 °C). The outcomes of published studies show that the degree of thermal damage in the post-heated carbonate rocks is attributed to their rock fabric, microstructural patterns, mineral composition, texture, grain cementations, particle orientations, and grain contact surface area. The expressive variations in the engineering properties of these rocks subjected to the temperature (>500 °C) are the results of chemical processes (hydration, dehydration, deionization, melting, mineral phase transformation, etc.), intercrystalline and intergranular thermal cracking, the separation between cemented particles, removal of bonding agents, and internal defects. Thermally deteriorated carbonate rocks experience a significant reduction in their fracture toughness, static–dynamic strength, static–dynamic elastic moduli, wave velocities, and thermal transport properties, whereas their porous network properties appreciate with the temperature. The stress–strain curves illustrate that post-heated carbonate rocks show brittleness below a temperature of 400 °C, brittle–ductile transformation at a temperature range of 400 to 500 °C, and ductile behavior beyond this critical temperature. The aspects discussed in this review comprehensively describe the damage mechanism of thermally exploited carbonate rocks that can be used as a reference in rock mass classification, sub-surface investigation, and geotechnical site characterization.
- 7 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2752
Open AccessDamage Characteristics of Thermally Deteriorated Carbonate Rocks: A Review
This review paper summarizes the recent and past experimental findings to evaluate the damage characteristics of carbonate rocks subjected to thermal treatment (20–1500 °C). The outcomes of published studies show that the degree of thermal damage in the post-heated carbonate rocks is attributed to their rock fabric, microstructural patterns, mineral composition, texture, grain cementations, particle orientations, and grain contact surface area. The expressive variations in the engineering properties of these rocks subjected to the temperature (>500 °C) are the results of chemical processes (hydration, dehydration, deionization, melting, mineral phase transformation, etc.), intercrystalline and intergranular thermal cracking, the separation between cemented particles, removal of bonding agents, and internal defects. Thermally deteriorated carbonate rocks experience a significant reduction in their fracture toughness, static–dynamic strength, static–dynamic elastic moduli, wave velocities, and thermal transport properties, whereas their porous network properties appreciate with the temperature. The stress–strain curves illustrate that post-heated carbonate rocks show brittleness below a temperature of 400 °C, brittle–ductile transformation at a temperature range of 400 to 500 °C, and ductile behavior beyond this critical temperature. The aspects discussed in this review comprehensively describe the damage mechanism of thermally exploited carbonate rocks that can be used as a reference in rock mass classification, sub-surface investigation, and geotechnical site characterization.
- 2 July 2021
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 14 (14) , 1-12
Geotechnical characterization of bentonite-fly ash mixtures for their application as landfill liner in Pakistan
- 2 July 2021
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 14 (14) , 1-12
Geotechnical characterization of bentonite-fly ash mixtures for their application as landfill liner in Pakistan
- 1 June 2017
- Published by Springer Nature in Environmental Earth Sciences
- Vol. 76 (11) , 396
Characterization of locally available soil as a liner material for solid waste landfills in Sri Lanka
- 1 June 2017
- Published by Springer Nature in Environmental Earth Sciences
- Vol. 76 (11) , 396
Characterization of locally available soil as a liner material for solid waste landfills in Sri Lanka