Shahab Saqib
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shahab Saqib has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Ali Murtaza Rasool
National Engineering Services Pakistan (NESPAK), Lahore, Pakistan
2 shared publications - Hafiz Muhammad Awais Rashid
Department of Geological Engineering, University of Engineering & Technology Lahore, Lahore 54890, Pakistan
2 shared publications - Mohsin Usman Qureshi
Sohar University
2 shared publications - Danish Ali
Department of Mining and Nuclear Engineering, Missouri University of Science and Technology, Rolla, USA
1 shared publication - Muhammad Faraz Javaid
Department of Civil Engineering, University of Engineering & Technology, Lahore, Pakistan
1 shared publication - Muhammad Rizwan Riaz
Department of Civil Engineering, University of Engineering & Technology, Lahore, Pakistan
1 shared publication
Latest Publications
- 26 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Mining Sciences
- p. 391-407
A Field-Scale Investigation into the Strategic Location of Air Decks for Improved Blasting Performance
Airdeck blasting is a promising technique for improved blast efficiency, reducing explosive consumption, and enhancing fragmentation. Nevertheless, it lacks widespread adoption due to design guideline gaps and differing opinions on air deck placement. This study offers technical guidance based on field experiments to optimise air deck blasting. Full-scale blast experiments were conducted at four distinct limestone benches to evaluate the efficacy of air deck implementation. At Bench-1, experiments were performed using conventional blasting (with full-column charge) and air decks at three strategic air deck positions (i.e., top, mid, and bottom) within blast holes at a selected quarry site. For Benches 2 and 3, comparative fragmentation analyses were conducted between conventional blasts and those utilising air decks positioned in the middle of the explosive column. Furthermore, the impact of multiple mid-air decks within explosive columns was also evaluated at Bench-4. A comparison of blast fragmentation results revealed that fragments obtained through the air decking technique surpassed those from the full-column charge, regardless of air deck placement. Among the tested air deck positions, the single air deck positioned at the middle of the explosive column yielded superior fragmentation results than other locations. In addition, this technique showed a reduction in explosive charge, back break, and toe-related issues.
- 26 September 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Mining Sciences
- p. 391-407
A Field-Scale Investigation into the Strategic Location of Air Decks for Improved Blasting Performance
Airdeck blasting is a promising technique for improved blast efficiency, reducing explosive consumption, and enhancing fragmentation. Nevertheless, it lacks widespread adoption due to design guideline gaps and differing opinions on air deck placement. This study offers technical guidance based on field experiments to optimise air deck blasting. Full-scale blast experiments were conducted at four distinct limestone benches to evaluate the efficacy of air deck implementation. At Bench-1, experiments were performed using conventional blasting (with full-column charge) and air decks at three strategic air deck positions (i.e., top, mid, and bottom) within blast holes at a selected quarry site. For Benches 2 and 3, comparative fragmentation analyses were conducted between conventional blasts and those utilising air decks positioned in the middle of the explosive column. Furthermore, the impact of multiple mid-air decks within explosive columns was also evaluated at Bench-4. A comparison of blast fragmentation results revealed that fragments obtained through the air decking technique surpassed those from the full-column charge, regardless of air deck placement. Among the tested air deck positions, the single air deck positioned at the middle of the explosive column yielded superior fragmentation results than other locations. In addition, this technique showed a reduction in explosive charge, back break, and toe-related issues.
- Open Access
- 26 September 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 253
Evaluation of Strength Anisotropy in Foliated Metamorphic Rocks: A Review Focused on Microscopic Mechanisms
This review paper addresses the recent and past advancements in investigating the anisotropic behavior of foliated metamorphic rock strength subjected to uniaxial or triaxial compression loading, direct or indirect tensile loading, and shear loading. The experimental findings published in the literature show that the strength of foliated rocks is significantly affected by varying the angle β between weak planes and major principal stress. A higher value of strength is reported at β = 0° or 90°; whereas a low strength value is noted at intermediate angles between β = 0° and 90°. The strength anisotropy depends on the degree of schistosity or gneissosity, which is the result of the preferred arrangement of phyllosilicate minerals under differential pressures. The failure of foliated rocks starts at the microscopic scale because of the dislocation slip, plastic kinking, and fracturing in phyllosilicate minerals such as mica. Tensile wing cracks at the tip of the mica propagate parallel to the deviatoric stress. Then, intergranular and intragranular shear-tensile cracks coalesce and lead to rock failure. The weak planes’ orientation controls the mode of failure such that tensile splitting, slip failure, and shear failure across foliations are observed at β = 0°–30°, β = 30°–60°, β = 60°–90° respectively. In the past, several attempts have been made to formulate failure criteria to estimate rock strength using different mathematical and empirical approaches. Over the years, the trend has shifted towards discontinuum modeling to simulate rock failure processes and to solve problems from laboratory to upscaled levels.
- 26 September 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 253
Open AccessEvaluation of Strength Anisotropy in Foliated Metamorphic Rocks: A Review Focused on Microscopic Mechanisms
This review paper addresses the recent and past advancements in investigating the anisotropic behavior of foliated metamorphic rock strength subjected to uniaxial or triaxial compression loading, direct or indirect tensile loading, and shear loading. The experimental findings published in the literature show that the strength of foliated rocks is significantly affected by varying the angle β between weak planes and major principal stress. A higher value of strength is reported at β = 0° or 90°; whereas a low strength value is noted at intermediate angles between β = 0° and 90°. The strength anisotropy depends on the degree of schistosity or gneissosity, which is the result of the preferred arrangement of phyllosilicate minerals under differential pressures. The failure of foliated rocks starts at the microscopic scale because of the dislocation slip, plastic kinking, and fracturing in phyllosilicate minerals such as mica. Tensile wing cracks at the tip of the mica propagate parallel to the deviatoric stress. Then, intergranular and intragranular shear-tensile cracks coalesce and lead to rock failure. The weak planes’ orientation controls the mode of failure such that tensile splitting, slip failure, and shear failure across foliations are observed at β = 0°–30°, β = 30°–60°, β = 60°–90° respectively. In the past, several attempts have been made to formulate failure criteria to estimate rock strength using different mathematical and empirical approaches. Over the years, the trend has shifted towards discontinuum modeling to simulate rock failure processes and to solve problems from laboratory to upscaled levels.
- 15 December 2023
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series A
- Vol. 105 (1) , 1-13
A Machine Learning-Based User-Friendly Approach for Prediction of Traffic-Induced Vibrations and its Application for Parametric Study
- 15 December 2023
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series A
- Vol. 105 (1) , 1-13
A Machine Learning-Based User-Friendly Approach for Prediction of Traffic-Induced Vibrations and its Application for Parametric Study