Yong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yong Liu has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Johnny Kin On Sin
Department of Electronic and Computer Engineering, the Hong Kong University of Science and Technology, Hong Kong, China
5 shared publications - Linhua Huang
Department of Electronic and Computer Engineering, Hong Kong University of Science and Technology, Hong Kong, China
5 shared publications - Xin Peng
Department of Electronic and Computer Engineering, Hong Kong University of Science and Technology, Hong Kong, China
5 shared publications - Hao Feng
Department of Electronic and Computer Engineering, The Hong Kong University of Science and Technology, Hong Kong
4 shared publications Naoto Fujishima
Fuji Electric Company Ltd., Matsumoto, Japan
4 shared publicationsYuichi Onozawa
Fuji Electric Company Ltd., Matsumoto, Japan
4 shared publications
Latest Publications
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (9) , 4525-4531
Analysis and Characterization of the Punchthrough n-p-n Diode for Hard Switching Power Control Applications
In this article, analysis and characterization of a new punchthrough (PT) n-p-n diode are performed. Numerical analysis shows that the PT voltage $\textit{V}_{{\text{PT}}}$ and the p $^{{+}}$ width ratio are the critical parameters to control the hole injection efficiency of the PT n-p-n diode. As a result, a locally reduced carrier profile can be realized due to the existence of electron extraction. Experimental results show that the leakage current of the PT n-p-n diode at 400 K can be kept at a level similar to that of a conventional Self-adjusting P Emitter Efficiency Diode (SPEED) with a well-designed $\textit{V}_{{\text{PT}}}$ . In addition, a p $^{{+}}$ width ratio of 20% is optimal for a better peak reverse recovery current ( $\textit{I}_{{\text{rrm}}}$ ) and forward voltage ( $\textit{V}_{{\text{F}}}$ ) tradeoff relationship. Compared with SPEED, the PT n-p-n diode achieves a reduced $\textit{I}_{{\text{rrm}}}$ ( $-$ 21%) and minimized reverse recovery loss $\textit{E}_{{\text{rec}}}$ ( $-$ 18%) at a nominal current. It can realize a significantly reduced $\textit{I}_{{\text{rrm}}}$ ( $-$ 42%) even at a small current and a bus voltage of 800 V. Moreover, better reverse recovery performances of the PT n-p-n diode are maintained at 400 K.
- 19 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (9) , 4525-4531
Analysis and Characterization of the Punchthrough n-p-n Diode for Hard Switching Power Control Applications
In this article, analysis and characterization of a new punchthrough (PT) n-p-n diode are performed. Numerical analysis shows that the PT voltage $\textit{V}_{{\text{PT}}}$ and the p $^{{+}}$ width ratio are the critical parameters to control the hole injection efficiency of the PT n-p-n diode. As a result, a locally reduced carrier profile can be realized due to the existence of electron extraction. Experimental results show that the leakage current of the PT n-p-n diode at 400 K can be kept at a level similar to that of a conventional Self-adjusting P Emitter Efficiency Diode (SPEED) with a well-designed $\textit{V}_{{\text{PT}}}$ . In addition, a p $^{{+}}$ width ratio of 20% is optimal for a better peak reverse recovery current ( $\textit{I}_{{\text{rrm}}}$ ) and forward voltage ( $\textit{V}_{{\text{F}}}$ ) tradeoff relationship. Compared with SPEED, the PT n-p-n diode achieves a reduced $\textit{I}_{{\text{rrm}}}$ ( $-$ 21%) and minimized reverse recovery loss $\textit{E}_{{\text{rec}}}$ ( $-$ 18%) at a nominal current. It can realize a significantly reduced $\textit{I}_{{\text{rrm}}}$ ( $-$ 42%) even at a small current and a bus voltage of 800 V. Moreover, better reverse recovery performances of the PT n-p-n diode are maintained at 400 K.
- 29 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (2) , 675-682
On-Resistance–Reliability Tradeoffs in Al₂O₃/LaAlO₃/SiO₂ Gate for SiC Power MOSFETs
On-resistance–reliability tradeoffs are investigated for SiC power MOSFETs using Al2O3/LaAlO3/SiO2 gate dielectrics. Due to the high gate capacitance, the Al2O3/LaAlO3/SiO2 gate device shows an improvement on the channel resistance ( ${R}_{\text {ch}}$ ) versus threshold voltage shift ( ${\Delta } {V}_{\text {th}}$ ) tradeoff compared to the SiO2 gate counterpart. Besides, the short-circuit withstand time of the Al2O3/LaAlO3/SiO2 gate device is 1.55 times longer than that of the SiO2 gate device, while the two devices have the same on-resistance. Furthermore, the predicted lifetime of the Al2O3/LaAlO3/SiO2 gate device is ten years at an effective electric field ( ${E}_{\text {eff}}$ ) of 4.8 MV/cm, which is comparable with the latest reported result of the SiO2 gate counterpart.
- 29 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (2) , 675-682
On-Resistance–Reliability Tradeoffs in Al₂O₃/LaAlO₃/SiO₂ Gate for SiC Power MOSFETs
On-resistance–reliability tradeoffs are investigated for SiC power MOSFETs using Al2O3/LaAlO3/SiO2 gate dielectrics. Due to the high gate capacitance, the Al2O3/LaAlO3/SiO2 gate device shows an improvement on the channel resistance ( ${R}_{\text {ch}}$ ) versus threshold voltage shift ( ${\Delta } {V}_{\text {th}}$ ) tradeoff compared to the SiO2 gate counterpart. Besides, the short-circuit withstand time of the Al2O3/LaAlO3/SiO2 gate device is 1.55 times longer than that of the SiO2 gate device, while the two devices have the same on-resistance. Furthermore, the predicted lifetime of the Al2O3/LaAlO3/SiO2 gate device is ten years at an effective electric field ( ${E}_{\text {eff}}$ ) of 4.8 MV/cm, which is comparable with the latest reported result of the SiO2 gate counterpart.
- 7 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (1) , 108-111
A Fast and Soft Reverse Recovery Diode With a Punch-Through NPN Structure
A fast and soft reverse recovery diode with a Punch-Through (PT) NPN structure is proposed and experimentally demonstrated. The structure features a P-type Schottky contact, a PT-NPN region for electron extraction, and a trench region with the bottom surrounded by a P-layer. Compared with conventional Self-adjusting P Emitter Efficiency Diode (SPEED), the proposed PT-NPN diode provides a much larger softness factor S (+23%), a shorter reverse recovery time T rr (-5%), and a much reduced reverse recovery charge Q rr (-20%) at nominal current.
- 7 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (1) , 108-111
A Fast and Soft Reverse Recovery Diode With a Punch-Through NPN Structure
A fast and soft reverse recovery diode with a Punch-Through (PT) NPN structure is proposed and experimentally demonstrated. The structure features a P-type Schottky contact, a PT-NPN region for electron extraction, and a trench region with the bottom surrounded by a P-layer. Compared with conventional Self-adjusting P Emitter Efficiency Diode (SPEED), the proposed PT-NPN diode provides a much larger softness factor S (+23%), a shorter reverse recovery time T rr (-5%), and a much reduced reverse recovery charge Q rr (-20%) at nominal current.
- 10 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (2) , 690-695
Static Performance and Threshold Voltage Stability Improvement of Al2O3/LaAlO3/SiO2Gate-Stack for SiC Power MOSFETs
Lateral metal–oxide–semiconductor field-effect transistors (MOSFETs) are fabricated on 4H-SiC utilizing deposited high- ${k}$ gate dielectrics. The high- ${k}$ gate-stack consists of thin nitrided SiO 2 and 40 nm of LaAlO 3 covered with a thin Al 2 O 3 cap. The high- ${k}$ gate MOSFET achieves a 40% reduction in channel resistance (at ${V}_{gs} = 15$ V) compared with that of the conventional SiO 2 gate MOSFET. In addition, bidirectional transfer characteristics of the high- ${k}$ gate MOSFET indicate slight hysteresis and show a superior threshold voltage stability compared to that of competitors, in a range of −15 V $\le {V}_{gs} \le16$ V under room and elevated temperatures. Therefore, the Al 2 O 3 /LaAlO 3 /SiO 2 gate-stack can provide both low on-resistance and good threshold voltage stability for SiC power MOSFETs.
- 10 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (2) , 690-695
Static Performance and Threshold Voltage Stability Improvement of Al2O3/LaAlO3/SiO2Gate-Stack for SiC Power MOSFETs
Lateral metal–oxide–semiconductor field-effect transistors (MOSFETs) are fabricated on 4H-SiC utilizing deposited high- ${k}$ gate dielectrics. The high- ${k}$ gate-stack consists of thin nitrided SiO 2 and 40 nm of LaAlO 3 covered with a thin Al 2 O 3 cap. The high- ${k}$ gate MOSFET achieves a 40% reduction in channel resistance (at ${V}_{gs} = 15$ V) compared with that of the conventional SiO 2 gate MOSFET. In addition, bidirectional transfer characteristics of the high- ${k}$ gate MOSFET indicate slight hysteresis and show a superior threshold voltage stability compared to that of competitors, in a range of −15 V $\le {V}_{gs} \le16$ V under room and elevated temperatures. Therefore, the Al 2 O 3 /LaAlO 3 /SiO 2 gate-stack can provide both low on-resistance and good threshold voltage stability for SiC power MOSFETs.
- 11 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (4) , 2133-2137
Characterization of Al2O3/LaAlO3/SiO2 Gate Stack on 4H-SiC After Post-Deposition Annealing
We fabricated Al 2 O 3 /LaAlO 3 /SiO 2 (ALS) gate stacks on 4H-SiC, with LaAlO 3 (LAO) film being annealed in O 2 atmosphere. The ALS gate stack annealed at 700 °C exhibits a much higher breakdown effective electric field ( ${E}_{\text {eff}}$ ), which is approximately 1.8 times higher than that of traditional SiO 2 gate oxide. The ALS gate stack also yields a low interface state density ( ${D}_{\text {it}}$ ) thanks to the intact LAO film. However, an annealing temperature as high as 800 °C induced traps in the LAO film and deteriorated the SiO 2 –SiC interface. The 700 °C-annealed LAO film with a high dielectric constant ( $\kappa $ ) of 14 and a low trap density, coupled with good electrical characteristics, makes it a promising gate dielectric for SiC power metal-oxide-semiconductor (MOS) device applications.
- 11 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (4) , 2133-2137
Characterization of Al2O3/LaAlO3/SiO2 Gate Stack on 4H-SiC After Post-Deposition Annealing
We fabricated Al 2 O 3 /LaAlO 3 /SiO 2 (ALS) gate stacks on 4H-SiC, with LaAlO 3 (LAO) film being annealed in O 2 atmosphere. The ALS gate stack annealed at 700 °C exhibits a much higher breakdown effective electric field ( ${E}_{\text {eff}}$ ), which is approximately 1.8 times higher than that of traditional SiO 2 gate oxide. The ALS gate stack also yields a low interface state density ( ${D}_{\text {it}}$ ) thanks to the intact LAO film. However, an annealing temperature as high as 800 °C induced traps in the LAO film and deteriorated the SiO 2 –SiC interface. The 700 °C-annealed LAO film with a high dielectric constant ( $\kappa $ ) of 14 and a low trap density, coupled with good electrical characteristics, makes it a promising gate dielectric for SiC power metal-oxide-semiconductor (MOS) device applications.
- Open Access
- 28 October 2020
- Published by Nanyang Technological University
Filter design of high power density converter with weight, size and thermal considerations
- 28 October 2020
- Published by Nanyang Technological University
Open AccessFilter design of high power density converter with weight, size and thermal considerations
- 8 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (6) , 2482-2488
A Trench-Field-Plate High-Voltage Power MOSFET
In this article, a trench-field-plate (TFP) high-voltage power MOSFET is proposed. Instead of using a conventional n⁻ drift region, the TFP power MOSFET features benzocyclobutene dielectric in the sidewall of deep trenches in the drift region and a sloped field plate (FP) inside each of the trenches. The TFP structure employed in the drift region modulates the electric field in the off-state, resulting in a higher breakdown voltage (BV) than that of conventional power MOSFETs. Simulation results show that the specific on-resistance of the TFP power MOSFET is approximately one-third that of the conventional power MOSFET and about 50% lower than that of the silicon limit for the same BV. In addition, compared with superjunction devices, the TFP power MOSFET is able to provide better reverse recovery characteristics, including a reduction in peak reverse recovery current (IRRM) and reverse recovery charge (QRR ) by 24% and 37%, respectively. Moreover, a p-i-n diode employing the TFP structure is fabricated, which is essentially identical to a power MOSFET in the off-state, to demonstrate the BV characteristics. The fabricated TFP p-i-n diode has a BV of 522 V, which is 2.3 times that of a conventional p-i-n diode fabricated on the same substrate.
- 8 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (6) , 2482-2488
A Trench-Field-Plate High-Voltage Power MOSFET
In this article, a trench-field-plate (TFP) high-voltage power MOSFET is proposed. Instead of using a conventional n⁻ drift region, the TFP power MOSFET features benzocyclobutene dielectric in the sidewall of deep trenches in the drift region and a sloped field plate (FP) inside each of the trenches. The TFP structure employed in the drift region modulates the electric field in the off-state, resulting in a higher breakdown voltage (BV) than that of conventional power MOSFETs. Simulation results show that the specific on-resistance of the TFP power MOSFET is approximately one-third that of the conventional power MOSFET and about 50% lower than that of the silicon limit for the same BV. In addition, compared with superjunction devices, the TFP power MOSFET is able to provide better reverse recovery characteristics, including a reduction in peak reverse recovery current (IRRM) and reverse recovery charge (QRR ) by 24% and 37%, respectively. Moreover, a p-i-n diode employing the TFP structure is fabricated, which is essentially identical to a power MOSFET in the off-state, to demonstrate the BV characteristics. The fabricated TFP p-i-n diode has a BV of 522 V, which is 2.3 times that of a conventional p-i-n diode fabricated on the same substrate.
- 9 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (10) , 4251-4257
Design and Characterization of the Deep-Trench, U-Shaped Field-Plate Edge Termination for 1200-V-Class SiC Devices
In this article, design and characterization of the deep-trench, U-shaped field-plate (DTUFP) edge-termination structure for 1200-V-class silicon carbide (SiC) devices are presented. A systematic numerical analysis shows that the trench depth, trench width, field-plate depth, and field-plate length are the four key structural parameters to determine the voltage blocking capability of the edge-termination structure. Experimental results demonstrate that the breakdown voltage of the proposed edge-termination structure can reach 1380 V when the edge-termination structure is well designed. Liquid crystal thermal measurement and destructive breakdown testing show that the ideal planar junction breakdown voltage has been achieved. The well-designed edge-termination structure has an ultrashort-edge width of 33 μm, which is approximately 75% shorter than that of the conventional guard-ring and junction termination extension (JTE) edge-termination structures.
- 9 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (10) , 4251-4257
Design and Characterization of the Deep-Trench, U-Shaped Field-Plate Edge Termination for 1200-V-Class SiC Devices
In this article, design and characterization of the deep-trench, U-shaped field-plate (DTUFP) edge-termination structure for 1200-V-class silicon carbide (SiC) devices are presented. A systematic numerical analysis shows that the trench depth, trench width, field-plate depth, and field-plate length are the four key structural parameters to determine the voltage blocking capability of the edge-termination structure. Experimental results demonstrate that the breakdown voltage of the proposed edge-termination structure can reach 1380 V when the edge-termination structure is well designed. Liquid crystal thermal measurement and destructive breakdown testing show that the ideal planar junction breakdown voltage has been achieved. The well-designed edge-termination structure has an ultrashort-edge width of 33 μm, which is approximately 75% shorter than that of the conventional guard-ring and junction termination extension (JTE) edge-termination structures.
- 1 February 2014
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 85 (2) , 025103
A direct tensile device to investigate the critical current properties in superconducting tapes
We construct an instrument to study the behavior of the critical current in superconducting tapes as a function of magnetic field and axial tension strain. The apparatus combines a material testing machine made by the non-magnetic stainless steel, which is capable of producing mechanical forces up to 1000 N and magnetic field up to 5 T with a homogeneous range of Φ150 × 110 mm. Moreover, the apparatus allows the automatic measurement of time dependence of voltage (V-t) under different magnetic fields and applied strains, which can be used to investigate the vortex instability and its time effect in the superconducting tapes. As an example, the simultaneous measurements of critical current and voltage relaxation with time at various strains and magnetic fields for the YaBa2Cu3O7−x coated conductors are carried out. Comparisons are made with the earlier reports in literature; the strain and magnetic field dependence of critical current indicate consistent behavior of this instrument.
- 1 February 2014
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 85 (2) , 025103
A direct tensile device to investigate the critical current properties in superconducting tapes
We construct an instrument to study the behavior of the critical current in superconducting tapes as a function of magnetic field and axial tension strain. The apparatus combines a material testing machine made by the non-magnetic stainless steel, which is capable of producing mechanical forces up to 1000 N and magnetic field up to 5 T with a homogeneous range of Φ150 × 110 mm. Moreover, the apparatus allows the automatic measurement of time dependence of voltage (V-t) under different magnetic fields and applied strains, which can be used to investigate the vortex instability and its time effect in the superconducting tapes. As an example, the simultaneous measurements of critical current and voltage relaxation with time at various strains and magnetic fields for the YaBa2Cu3O7−x coated conductors are carried out. Comparisons are made with the earlier reports in literature; the strain and magnetic field dependence of critical current indicate consistent behavior of this instrument.
- 24 May 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 729-733
A feasible superjunction device and process technology
- 24 May 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 729-733
A feasible superjunction device and process technology