SKSatya Prakash Kar

Satya Prakash Kar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Satya Prakash Kar has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A comparative study of pool boiling of acetone with anionic and cationic surfactant on coated aluminum surface

    by Abhishek Sinha Mahapatra, Satya Prakash Kar, Abhilas Swain, Radhakanta Sarangi

  • An Experimental Investigation on Pool Boiling Heat Transfer with Cationic Surfactant Solution on Copper Substrate

    by Abhishek Sinha Mahapatra, Satya Prakash Kar, Abhilas Swain, R. K. Sarangi, P. C. Sekhar

  • Biosurfactant Enhanced Saturated Pool Boiling Heat Transfer Over Plain Copper Surface and Prediction Through Machine Learning Algorithms

    by Pragati P. Sahu, Prashant K. Jha, Abhilas Swain, Radha K. Sarangi, Satya P. Kar

    This study investigates the impact of coco glucoside, a bio‐surfactant, on heat transfer during pool boiling experiments with acetone, methanol, and ethanol using a smooth copper surface. Solutions containing coco glucoside were tested at concentrations of 0.5, 1, and 1.5 mL per 100 mL of fluid (500, 1000, and 1500 ppm). The research focused on heat transfer coefficients (HTC), bubble formation, and surface temperatures to assess how coco glucoside influences heat transfer efficiency. The results are presented in terms of wall superheat and boiling HTC with respect to heat flux and concentration of coco‐glucoside. The results indicate that coco glucoside enhances heat transfer efficiency in acetone and methanol when used at concentrations up to 1000 ppm. Specifically, the maximum HTC observed at the 1 mL concentration of surfactant was 12,121 W/m²K for acetone and 8185 W/m²K for methanol, representing improvements of 11% and 26%, respectively, compared to pure liquids. These improvements are attributed to lower surface tension and enhanced bubble nucleation. However, at a concentration of 1500 ppm, a decrease in HTC was noted, likely due to micelle formation. In contrast, ethanol exhibited a continuous increase in HTC with rising coco glucoside concentration, achieving a 35% improvement at 1500 ppm. Additionally, the study explored predicting HTC using machine learning algorithms. K‐nearest neighbors (KNNs) and random forest models were evaluated. KNN achieved an R² of 0.9895 and a mean absolute percentage error (MAPE) of 7.495% for acetone, while random forest (RF) showed an R² of 0.9785 and a MAPE of 12.01% for ethanol. These findings demonstrate the potential of coco glucoside in improving heat transfer and the effectiveness of machine learning in optimizing thermal management processes.


  • Numerical investigation of a novel method of laser assisted cryopreservation of biological tissue considering non-fourier heat conduction

    by Siladitya Sukumar, Satya Prakash Kar

    The present article proposes a numerical model for a novel laser assisted cryopreservation through vitrification of biological tissue. A two-dimensional numerical model is developed considering the non-Fourier heat conduction. The Finite Volume Method is used for discretization of the governing differential equation while the Tri-diagonal Matrix Algorithm (TDMA) is used for solving the resulting discretized algebraic equation in order to obtain the temperature distribution inside the tissue domain. The existing enthalpy method is modified considering the thermal relaxation time to capture the freezing front. With the increase in thermal relaxation time value, rate of heat transfer and rise in temperature during laser heating decreases and rate of heat loss during freezing also decreases. This reduces the length up to which vitrification is achieved. So, a proper size of the tissue is to be chosen to achieve the desired freezing rate. This length may vary based on the laser parameters and the thermal relaxation time. However, the validity of the present study may be examined experimentally in real ambient conditions before application in tissue preservation.


  • EFFECT OF SURFACTANT ON SATURATED POOL BOILING OVER POROUS COATED SURFACE

    by Abhishek Sinha Mahapatra, Satya Prakash Kar, Abhilas Swain

    The present study reports the investigation on heat transfer enhancement due to the combined effect of coating on heater surface and addition of surfactant to test liquid during saturated pool boiling. It is achieved by TiO2 coating on aluminum heater surface combined with addition of surfactant sodium lauryl sulphate (SLS) to different base liquids such as acetone, ethanol, and isopropanol. The experiments were conducted under saturated condition and varying the surfactant concentration between 200 and 1000 ppm. The heat flux is varied within the range 13-65 kW/m2. The pool boiling heat transfer coefficients and surface superheats are determined and analyzed. The pool boiling heat transfer coefficients are found to be increasing with addition of surfactant up to 400 ppm, which is the critical micelle concentration (CMC), and deteriorates beyond the 400 ppm. The enhancement factors are determined, which are the ratios between the pool boiling heat transfer coefficients over coated surface to that of plain surface. Finally, it is realized that the enhancement factors are higher for the lower surfactant concentration irrespective of the base fluid. It decreases as the heat flux increases for a particular surfactant concentration. It is found to be higher for pure liquid and with concentrations of surfactant below 400 ppm. For higher concentrations of surfactant, the enhancement factors are not so significant. However, its value lies in the range of 1.5 to 3 for all combinations of surfactant and base fluid.


  • Review on thermal performance of heat exchanger using phase change material

    by P. Das, S. P. Kar, R. K. Sarangi

    Summary: This article reports detailed investigation of using different Phase Change Materials (PCM) in various designs of Thermal Energy Storage (TES) Devices: specifically, heat exchanger. The focus is on the performance analysis of different types of heat exchangers acting as TES having various PCMs which are substantially reviewed in this paper. The study highlights the difference in their geometry and performance output. Further, the importance of different performance enhancement methods with parametric study of different heat exchangers using PCM is described. From the detailed investigation, finally, it is realised that the different factors such as no. of outer tubes, no. of inner tubes, tube material selected, type of PCM, provision of an extended surface, use of different metal foams and nanoparticles, various types of composites, charging and discharging characteristics and packed and cascaded units are different heat transfer enhancement methods to improve the heat transfer. A novel kind of heat exchanger known as Webbed tube heat exchanger using PCM is discussed for an efficient TES unit. Further, a review of quantitative analysis of melting time, solidification time, charging and discharging time is discussed.


  • Numerical analysis of laser melting of alumina coated steel

    by Rajat Kumar Dey, Satya Prakash Kar, P. Chandrasekhar

  • Experimental analysis of saturated pool boiling of acetone and isopropanol with added surfactant sodium lauryl sulfate over aluminum surface

    by Abhishek Sinha Mahapatra, Satya Prakash Kar, Abhilas Swain

    The present article reports a detailed experimental study to know the effect of adding surfactants to different base fluids. For this purpose, an aqueous solution of different concentrations of surfactant with base fluids was formed and then heated at varying heat flux in a pool boiling apparatus. Acetone and isopropanol have been used as base/boiling fluids with anionic surfactant sodium lauryl sulfate (SLS) of 200, 400, 600, 800, and 1000 PPM concentration. The data obtained by heating surfactant‐based fluids has been compared to the data of heating pure base fluids to establish the role of surfactants and the importance of surfactant concentration, that is, critical micelle concentration (CMC) in pool boiling augmentation. CMC value was found in the case of pool boiling of acetone with an SLS concentration of 400 PPM. However, the CMC value is found to be a lower value of SLS concentration of 200 PPM in the pool boiling process of isopropanol. Therefore, it is interesting to investigate the possible causes of such heat transfer phenomena with different values of surfactant concentration. Variations in heat flux change the degree of superheat of the aluminum heater substrate. The heat transfer performance is studied, and finally, a semi‐empirical correlation is proposed to know the heat transfer coefficient and its dependency over the concentration of surfactant.


  • Open Access

    Performance enhancement with inorganic phase change materials for the application of thermal energy storage: A critical review

    by Rohan Kundu, Satya Prakash Kar, Radhakanta Sarangi

    In the current energy crisis, energy saving becomes important to reduce the gap of supply and demand of energy. Phase change material (PCM) plays a bigger role to store energy due to its high latent of fusion. The present article provides an insight into the present developments in enhancing the performance of inorganic PCMs. In this article, a comprehensive review of different techniques like mixing of different salts, addition of nanoparticle, addition of nucleating agents, encapsulation methods and so on are discussed in detail. Special attention is given to know the enhancement in high thermal conductivity, large phase change enthalpy, high density, thermal stability, corrosion resistance and so on.


  • Modeling for Fluid Flow and Heat Transfer in Closed Loop Pulsating Heat Pipe

    by R. K. Sarangi, S. P. Kar, M. V. Rane, A. Swain, L. K. Pothal

    Numerical modeling of multi-turn closed-loop pulsating heat pipe (CLPHP) is presented in this paper for ethanol as a working fluid. Modeling is carried out for 1-mm and 2-mm ID PHP for different numbers of turns, different orientations, and at constant wall temperature boundary conditions. Momentum and heat transfer variations with time are investigated numerically solving the one-dimensional governing equations for vapor bubble and liquid plugs. Evaporation and condensation take place by heat transfer through liquid film present around the vapor bubble. The code takes into account the realistic phenomena such as vapor bubble generation, liquid plug merging, and superheating of vapor bubbles above its saturation temperature. During the merging of liquid plugs, a time-step adaptive scheme is implemented and this minimum time-step was found to be 10−7 s. Nature of flow is investigated by momentum variation plot. Model results are compared with the experimental results from literature for nine different cases. Maximum variation in heat transfer for all these cases is found to be below ±34%.