KSKannivel Saravanakumar

Kannivel Saravanakumar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kannivel Saravanakumar has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Effect of Fiber Hybridization on Mechanical Behavior of Hybrid Composite Laminates

    by N. Bharat, L. R. Ganapathy Subramanian, K. Saravanakumar

    In this research work, the mechanical properties of hybrid composite laminates were investigated by conducting quasi‐static indentation, tensile, and three‐point bending tests. Woven glass fiber (G), carbon fiber (C), Kevlar fiber (K), and carbon‐Kevlar intraply (I) fiber mats were utilized to produce a variety of hybrid laminate configurations. The matrix system consists of LY556 epoxy resin and HY951 hardener, combined in a ratio of 10:1. Seven configurations of hybrid laminates including [G 6 ] S , [I/G] 3S , [I 3 /G 3 ] S , [C/G] 3S , [C 3 /G 3 ] S , [K/G] 3S , and [K 3 /G 3 ] S were manufactured. All the laminates were subjected to a quasi‐static indentation test to assess the peak load, absorbed energy, contact stiffness, and residual dent. The area of damage caused by indentation was analyzed using ultrasonic testing. Tensile and flexural strengths of the hybrid laminates were evaluated, and their results were correlated. The damage morphology was also examined using optical and scanning electron microscopy. This study reveals that the hybridization strategy dictates a critical performance trade‐off. Results show that the clustered [I 3 /G 3 ] S configurations dominated in flexural strength by 250% and indentation resistance by 114% peak load, whereas distributed sequences [C/G] 3S achieve superior in‐plane tensile strength by 100%, respectively. It was observed that inserting high‐stiffness plies to the outer layer can enhance bending rigidity and load‐bearing capability. [I/G] 3S and [C/G] 3S exhibited progressive failure behavior and greater damage tolerance capability, while [I 3 /G 3 ] S and [C 3 /G 3 ] S failed catastrophically.


  • Influence of milled glass fillers on mode-II fracture toughness of polymer composites

    by K. Saravanakumar, Nibras Farouk, C. Suresh Kumar, V. Arumugam

    This work focuses on investigating the effect of interface fibre orientation with milled glass fillers on mode-II fracture toughness of [0°7/θ°//θ°/0°7] glass/epoxy laminates. The result reveals that the loading of 5 wt-% milled glass fillers in the epoxy matrix enhanced the interlaminar fracture toughness. Significantly, the filler-loaded samples improved the fracture toughness by 232% (3.32 times) in 0°/0° and 184% (2.84 times) in ±45° interface fibre orientation compared to the baseline samples. In addition, the interlaminar shear strength increased was increased by 82% in 0°/0° interface and 76% in ±45° interface fibre orientation. Finally, field emission scanning electron microscopic (FESEM) was used to study the fracture surfaces of different fibre orientations.


  • Effect of patch hybridisation on indentation resistance and residual performance of patch repaired glass/epoxy laminates using acoustic emission monitoring

    by K. Shruthi, K. Saravanakumar, V. Arumugam, C. Suresh Kumar

    This research work focuses on investigating the effect of external patch repair and its sequence on quasi-static indentation (QSI) response of glass/epoxy laminates. The parent woven glass/epoxy laminates (Type-I) was repaired by using woven (W) and chopped (C) fibres with different patch sequence such as W/W/W/W (Type II), W/C/C/W (Type III), C/W/W/C (Type IV) and C/C/C/C (Type V). The aim of using hybrid patches was to combine the higher load resistance of woven glass fibres and stable crack propagation of chopped fibres. The evolution of damage in different repair patches was observed and their damage mechanisms associated during loading were characterised with online acoustic emission (AE) monitoring. The results noticed that the Type III and Type IV samples exhibited higher peak force by an average of 37% compared to Type II and Type V samples. Moreover, the Type III and Type IV samples showed higher contact stiffness by 3.77 and 2.74 times than the Type II samples. Correspondingly, the Type III and Type IV samples indicated higher damage onset load by an average of 80% compared to the Type II samples. Overall, the Type III samples revealed superior indentation performance with higher peak load and minor residual dent. In contrast, the indentation resistance of Type IV samples was better for lower indentation depths. However, the Type III laminates have greater ability to resist crack progression through crack diversion and debonding of fibre at the repair patch interface.


  • Open Access

    Low-Velocity Impact Induced Damage Evaluation and Its Influence on the Residual Flexural Behavior of Glass/Epoxy Laminates Hybridized with Glass Fillers

    by Saravanakumar Kannivel, Harini Subramanian, Vellayaraj Arumugam, Hom N. Dhakal

    This research work investigates the low-velocity impact induced damage behavior and its influence on the residual flexural response of glass/epoxy composites improved with milled glass fillers. The low-velocity impact damage employing varying impact velocities (3 m/s, 3.5 m/s, and 4 m/s) was induced on baseline and filler loaded samples with different fiber orientations. The residual performance and their damage modes were characterized using post impact flexural (FAI) test and acoustic emission (AE) monitoring. In all fiber orientations, the filler modified glass/epoxy samples showed improved impact strength and stiffness properties. A substantial improvement in impact damage tolerance, especially for samples impacted at 3.5 m/s and 4 m/s was observed. The presence of filler at the interlaminar zone contributed to improved energy dissipation through filler debonding and pull-out. This further contributed in arresting the crack growth, showing reduced damaged area. The inclusion of milled fibers on glass/epoxy laminates enhanced the impact toughness and residual flexural behavior.


  • Damage monitoring of glass/epoxy laminates with different interply fiber orientation using acoustic emission

    by K Saravanakumar, C Suresh Kumar, V Arumugam

    This article investigates the effects of interface fiber orientation on the mode-I interlaminar fracture toughness, and the evolution of damage was monitored using acoustic emission technique. The results show that changing the interply fiber orientation improved the fracture toughness and delamination resistance significantly. The GIC initiation fracture toughness was found to increase by 87%, 71%, and 69% for 0°/45°, 0°/90°, and ±45° interfaces, respectively. The improvement in fracture toughness was attributed to the crack path diversion along the interply fiber orientation which offered more resistance to crack propagation. In addition, sentry function was also computed based on the correlation between the mechanical strain energy accumulated in the laminates, and the acoustic energy that propagates by fracture events made it possible to evaluate the delamination resistance. The results show that 0°/45° has high resistance to crack propagation followed by 0°/90°, ±45°, and 0°/0°. Finally, scanning electron microscopic analysis was used to determine the fracture surface in different interply fiber orientation of glass/epoxy laminates.


  • Open Access

    Influence of Milled Glass Fiber Fillers on Mode I & Mode II Interlaminar Fracture Toughness of Epoxy Resin for Fabrication of Glass/Epoxy Composites

    by Kannivel Saravanakumar, Vellayaraj Arumugam, Rotte Souhith, Carlo Santulli

    The present work is focused on improving mode I and mode II delamination resistance of glass/epoxy composite laminates (50 wt.% of glass fibers) with milled glass fibers, added in various amounts (2.5, 5, 7.5 and 10% of the epoxy weight). Including fillers in the interlayer enhances the delamination resistance by providing a bridging effect, therefore demanding additional energy to initiate the crack in the interlaminar domain, which results in turn in enhanced fracture toughness. The maximal increase of mode I and mode II fracture toughness and of flexural strength was obtained by the addition of 5% milled glass fiber. The mechanism observed suggests that crack propagation is stabilized even leading to its arrest/deflection, as a considerable amount of milled glass fiber filler was oriented transverse to the crack path. In contrast, at higher filler loading, tendency towards stress concentration grows due to local agglomeration and improper dispersion of excess fillers in inter/intralaminar resin channel, causing poor adhesion to the matrix, which leads to reduction in fracture toughness, strength and strain to failure. Fractured surfaces analyzed using scanning electron microscopy (SEM) revealed a number of mechanisms, such as crack deflection, individual debonding and filler/matrix interlocking, all contributing in various ways to improve fracture toughness.


  • Effect of thickness on indentation response and tensile loading behaviour of glass/epoxy laminates under acoustic emission monitoring

    by Saravanakumar Kannivel, Arumugam Vellayaraj, Ismailzabeeullah Kolimi, Janietha Thomas

    This research work investigates the effect of thickness on the quasi-static indentation and tensile loading behaviour of glass/epoxy laminates. Cross-ply [0°/90°]3S laminates fabricated at different process pressures (40 kg/cm2, 50 kg/cm2 and 60 kg/cm2) were subjected to quasi-static indentation loading. Furthermore, the residual load-bearing capacity was estimated by performing tensile after indentation (TAI) test. The damage development and corresponding failure mechanisms associated during loading were characterised by acoustic emission monitoring. The results show that the damage onset load, residual dent and damage area were dependent on the thickness of the laminates. Type II samples (processed at 50 kg/cm2) exhibited higher damage onset load and contact stiffness by an average of 20% and 25% than type I and type III laminates. Higher peak force, reduced damage area and permanent dent were attributed to greater elastic response. In contrast, Type I samples (processed at 40 kg/cm2) with thick resin-rich zone exhibited severe delamination through transverse shear cracking. This observation was also evident from the intense AE signals related to debonding/delamination modes, which correlates well with the damage area.


  • Open Access

    QUASI-STATIC INDENTATION BEHAVIOR OF GFRP WITH MILLED GLASS FIBER FILLER MONITORED BY ACOUSTIC EMISSION

    by Kannivel Saravanakumar, Balakrishnan Sai Lakshminarayanan, Vellayaraj Arumugam, Carlo Santulli, Ana Pavlovic, Cristiano Fragassa

    This paper aims at investigating the influence of the addition of milled glass fibers upon quasi-static indentation (QSI) properties of glass/epoxy composite laminates. The QSI behavior was experimentally studied by evaluating indentation force, residual dent depth, energy absorbed and size of the damaged area for different indentation depths. Following the QSI tests, the filler-loaded glass/epoxy samples were subjected to three-point bending tests in order to measure residual flexural strength, and the results were compared with the baseline glass/epoxy samples. Both tests were performed with online acoustic emission monitoring in order to observe damage progression and characterize different fracture mechanisms associated with loading. The results show that the filler-loaded laminates exhibit a substantial improvement in the peak force and contact stiffness, with a reduced permanent damage both in terms of depth and of area, in comparison with the baseline ones. It is found that the filler presence offers greater stiffness and higher energy dissipation through toughening mechanisms such as filler debonding/pullout and filler bridging/interlocking.


  • Characterization of failure mechanism in glass, carbon and their hybrid composite laminates in epoxy resin by acoustic emission monitoring

    by Suresh Kumar Chelliah, Saravana Kumar Kannivel, Arumugam Vellayaraj

    Fibre reinforced plastic (FRP) composites are being widely utilized in various industries because of their superior mechanical properties. Besides their advantages, failure of these composites can occur either by an individual or an associated of various failure modes which are very difficult to distinguish and discriminate the damages. This paper focuses on solving this issue, by characterizing the various failure modes in glass, carbon and their hybrid composite laminates in epoxy resin under uni-axial tensile loading with acoustic emission (AE) monitoring. AE data recorded during the testing of a pure-resin specimen and the single-layer specimen were used to identify the matrix cracking and debonding, respectively, whereas delamination was predominant in a two-layer specimen. The fibre failure was obtained from the resin impregnated single fibre strand. The parametric studies using AE amplitude, duration, AE cumulative counts, AE cumulative energy, rise angle (RA) and peak frequency were used to describe the damage mechanism of the different stacking sequence of glass fibre reinforced plastic (GFRP), carbon fibre reinforced plastic (CFRP) and their hybrid composite laminates. The mechanical parameter and AE parameter was successfully correlated for discrimination of damage mechanism. The individual failure mode of glass, carbon and their hybrid composite laminates with the most critical damage mechanisms and the time-to-failure were investigated.