Olga G. Lenivtseva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Olga G. Lenivtseva has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
I A Polyakov
Novosibirsk State Technical University, 20, K. Marx Prospekt, 630073, Novosibirsk, Russia
7 shared publications- Vitaliy V. Samoylenko
Novosibirsk State Technical University, Novosibirsk, 630073 Russia
6 shared publications - Daria Viktorovna Lazurenko
Novosibirsk State Technical University, Novosibirsk, Russia
5 shared publications - Ivan Anatolyevich Bataev
Novosibirsk State Technical University, Novosibirsk, Russia
5 shared publications V V Samoylenko
Novosibirsk State Technical University, 20, K. Marx Prospekt, 630073, Novosibirsk, Russia
5 shared publicationsIgor A. Polyakov
4 shared publications
Latest Publications
- 1 April 2018
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 20 (2) , 116-129
Surface Hardening of Commercially Pure Titanium by Non-vacuum Electron Beam Cladding of Powder Mixtures
- 1 April 2018
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 20 (2) , 116-129
Surface Hardening of Commercially Pure Titanium by Non-vacuum Electron Beam Cladding of Powder Mixtures
- Open Access
- 7 November 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 129, 02022
Structure and wear resistance of Ti-TiC-TiB layers obtained by non-vacuum electron beam cladding
In this study structure and tribotechnical properties of cp-titanium after non-vacuum electron beam cladding of powder mixture containing boron carbide were investigated. Structural investigations were carried out using optical and scanning electron microscopy and X-ray analysis. The thickness of cladded layers was 1.3…2.5 mm. The beam moving speed was not influence the phase composition of coatings. The main phases of the surface layers were α- titanium (α′.- titanium), titanium carbide TiC and titanium boride TiB. It was determined that the average value of microhardness of the samples formed with the speed 25 mm/s was three times higher in comparison with substrate metal. A decrease in the beam moving speed led to an increase in the heat input per unit area and was accompanied by a reduction in the coating microhardness. To evaluate the wear resistance, friction test of the obtained materials against fixed abrasive particles was performed. The maximum relative wear resistance was exhibited by the coatings after cladding of 20 wt. % boron carbide and 30 wt. % titanium with the beam moving speed of 25 mm/s. Their wear resistance was 1.53 times higher as compared to cp-titanium.
- 7 November 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 129, 02022
Open AccessStructure and wear resistance of Ti-TiC-TiB layers obtained by non-vacuum electron beam cladding
In this study structure and tribotechnical properties of cp-titanium after non-vacuum electron beam cladding of powder mixture containing boron carbide were investigated. Structural investigations were carried out using optical and scanning electron microscopy and X-ray analysis. The thickness of cladded layers was 1.3…2.5 mm. The beam moving speed was not influence the phase composition of coatings. The main phases of the surface layers were α- titanium (α′.- titanium), titanium carbide TiC and titanium boride TiB. It was determined that the average value of microhardness of the samples formed with the speed 25 mm/s was three times higher in comparison with substrate metal. A decrease in the beam moving speed led to an increase in the heat input per unit area and was accompanied by a reduction in the coating microhardness. To evaluate the wear resistance, friction test of the obtained materials against fixed abrasive particles was performed. The maximum relative wear resistance was exhibited by the coatings after cladding of 20 wt. % boron carbide and 30 wt. % titanium with the beam moving speed of 25 mm/s. Their wear resistance was 1.53 times higher as compared to cp-titanium.
- Open Access
- 1 January 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 168 (1) , 012076
Welding of a corrosion-resistant composite material based on VT14 titanium alloy obtained using an electron beam emitted into the atmosphere
The study investigates the possibility of inert gas arc welding of a double layer composite material on a titanium base with an anti-corrosive layer obtained by fused deposition of a powder mix containing tantalum and niobium over a titanium base using an electron beam emitted into the atmosphere. Butt welding and fillet welding options were tested with two types of edge preparation. Welds were subjected to a metallographic examination including a structural study and an analysis of the chemical and phase composition of the welds. A conclusion was made regarding the possibility of using welding for manufacturing of items from the investigated composite material.
- 1 January 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 168 (1) , 012076
Open AccessWelding of a corrosion-resistant composite material based on VT14 titanium alloy obtained using an electron beam emitted into the atmosphere
The study investigates the possibility of inert gas arc welding of a double layer composite material on a titanium base with an anti-corrosive layer obtained by fused deposition of a powder mix containing tantalum and niobium over a titanium base using an electron beam emitted into the atmosphere. Butt welding and fillet welding options were tested with two types of edge preparation. Welds were subjected to a metallographic examination including a structural study and an analysis of the chemical and phase composition of the welds. A conclusion was made regarding the possibility of using welding for manufacturing of items from the investigated composite material.
- 15 December 2016
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- No. 4,p. 63-74
Structure and properties of TiB-TiC-Ti layers fabricated on cp-titanium substrates by electron beam cladding
- 15 December 2016
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- No. 4,p. 63-74
Structure and properties of TiB-TiC-Ti layers fabricated on cp-titanium substrates by electron beam cladding
- Open Access
- 8 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 156 (1) , 012023
Corrosion resistance of Ti-Ta-Zr coatings in the Boiling Acid Solutions
In this study corrosion resistance of Ti-Ta-Zr coatings fabricated on VT14 titanium alloy workpieces using a high-energy electron beam injected in the atmosphere was investigated. Estimation of corrosion resistance of surface alloyed layers was carried out by the weight-change method. Boiling solution of 65 % nitric acid in water and 5 % of sulfuric acid in water were used as the corrosive environments. Investigation of samples after corrosion tests was carried out using a Carl Zeiss EVO 50 XVP scanning electron microscope.
- 8 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 156 (1) , 012023
Open AccessCorrosion resistance of Ti-Ta-Zr coatings in the Boiling Acid Solutions
In this study corrosion resistance of Ti-Ta-Zr coatings fabricated on VT14 titanium alloy workpieces using a high-energy electron beam injected in the atmosphere was investigated. Estimation of corrosion resistance of surface alloyed layers was carried out by the weight-change method. Boiling solution of 65 % nitric acid in water and 5 % of sulfuric acid in water were used as the corrosive environments. Investigation of samples after corrosion tests was carried out using a Carl Zeiss EVO 50 XVP scanning electron microscope.
- Open Access
- 8 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 156 (1) , 012021
Structure and properties of Ti-C-B coatings produced by non-vacuum electron beam cladding
Cp-Ti/TiB+TiC wear-resistance coatings produced by non-vacuum electron beam cladding of boron carbide and titanium powders are studied in the paper. The X-ray phase analysis of the composite coatings microstructure showed that titanium carbide and boride reinforcing particles are evolved during the process. The obtained data are in good agreement with results of optical and electron microscopy. Undissolved particles of the initial boron carbide powder are detected in the coatings. The microhardness test as well as wear resistance test of materials under conditions of loose abrasive particles are conducted. It is established that the precipitation of reinforcing particles improves the tribological properties of the composite coatings.
- 8 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 156 (1) , 012021
Open AccessStructure and properties of Ti-C-B coatings produced by non-vacuum electron beam cladding
Cp-Ti/TiB+TiC wear-resistance coatings produced by non-vacuum electron beam cladding of boron carbide and titanium powders are studied in the paper. The X-ray phase analysis of the composite coatings microstructure showed that titanium carbide and boride reinforcing particles are evolved during the process. The obtained data are in good agreement with results of optical and electron microscopy. Undissolved particles of the initial boron carbide powder are detected in the coatings. The microhardness test as well as wear resistance test of materials under conditions of loose abrasive particles are conducted. It is established that the precipitation of reinforcing particles improves the tribological properties of the composite coatings.
- Open Access
- 8 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 156 (1) , 012024
The study of the modes of Ta-Zr powder mixture non-vacuum electron-beam cladding on the surface of the cp-titanium plates
The effect of the modes of non-vacuum electron-beam cladding of Ta-Zr powder mixtures on the structure and properties of the layers formed on the surface of cp-titanium were studied. The mode of the electron-beam alloying of titanium with zirconium and tantalum, which ensured the formation of a defect-free layer with a high content of alloying elements was selected. Metallographic examination indicated the presence of a dendritic- and plate-type structure of cladded layers. The microhardness of the layers, formed at the optimum mode, was not changed in the cross section and was equal to 450 HV.
- 8 November 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 156 (1) , 012024
Open AccessThe study of the modes of Ta-Zr powder mixture non-vacuum electron-beam cladding on the surface of the cp-titanium plates
The effect of the modes of non-vacuum electron-beam cladding of Ta-Zr powder mixtures on the structure and properties of the layers formed on the surface of cp-titanium were studied. The mode of the electron-beam alloying of titanium with zirconium and tantalum, which ensured the formation of a defect-free layer with a high content of alloying elements was selected. Metallographic examination indicated the presence of a dendritic- and plate-type structure of cladded layers. The microhardness of the layers, formed at the optimum mode, was not changed in the cross section and was equal to 450 HV.
- Open Access
- 20 April 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 124 (1) , 012117
The influence of non-vacuum electron-beam facing on the structure of Ti-Ta layers formed on the surface of VT1-0 alloy
The influence of electron-beam facing modes on the structure of Ti-Ta layers formed on the surface of commercially pure titanium VT1-0 has been studied in the paper. The mode of the electron-beam treatment of alloying powder mixture, by which there were no defects in the pad, has been identified. The methods of optical microscopy and scanning electron microscopy have shown that in pads there is dendritic segregation typical for the process of initial crystallisation. At greater magnifications it is possible to observe a structure of the laminar type. The X-ray phase analysis of titanium-tantalum layers justifies the presence of two phases: a hexagonal α'-phase and a cubic (β-phase of titanium.
- 20 April 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 124 (1) , 012117
Open AccessThe influence of non-vacuum electron-beam facing on the structure of Ti-Ta layers formed on the surface of VT1-0 alloy
The influence of electron-beam facing modes on the structure of Ti-Ta layers formed on the surface of commercially pure titanium VT1-0 has been studied in the paper. The mode of the electron-beam treatment of alloying powder mixture, by which there were no defects in the pad, has been identified. The methods of optical microscopy and scanning electron microscopy have shown that in pads there is dendritic segregation typical for the process of initial crystallisation. At greater magnifications it is possible to observe a structure of the laminar type. The X-ray phase analysis of titanium-tantalum layers justifies the presence of two phases: a hexagonal α'-phase and a cubic (β-phase of titanium.
- Open Access
- 20 April 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 124 (1) , 012128
Influence of Electron Beam Treatment Regimes on the Structure and Properties of Intermetallic Clads Obtained on Titanium Substrates
Intermetallic clads were obtained on the basis of the titanium workpieces. The cladding was carried out using a non-vacuum electron beam treatment technique. A powder mixture which contained 16.97 Al - 28.27 Ti - 41.07 CaF2 - 13.69 LiF (wt. %) was used for cladding. Two regimes with the beam current of 16 mA and 18 mA were used. The beam current influenced significantly the structure and phase composition of clads. In case of the electron beam treatment with a beam current of 16 mA a lamellar structure consisted of a mixture of AlTi3 and A1Ti was fabricated. An increase of the beam current to 18 mA led to the formation of an AlTi3 acicular structure. Microhardness and wear resistance of the intermetallic coating was significantly higher in comparison with cp-Ti. The maximum microhardness of clads was 480 HV. A wear rate of clads was 10 times lower than that of cp-Ti.
- 20 April 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 124 (1) , 012128
Open AccessInfluence of Electron Beam Treatment Regimes on the Structure and Properties of Intermetallic Clads Obtained on Titanium Substrates
Intermetallic clads were obtained on the basis of the titanium workpieces. The cladding was carried out using a non-vacuum electron beam treatment technique. A powder mixture which contained 16.97 Al - 28.27 Ti - 41.07 CaF2 - 13.69 LiF (wt. %) was used for cladding. Two regimes with the beam current of 16 mA and 18 mA were used. The beam current influenced significantly the structure and phase composition of clads. In case of the electron beam treatment with a beam current of 16 mA a lamellar structure consisted of a mixture of AlTi3 and A1Ti was fabricated. An increase of the beam current to 18 mA led to the formation of an AlTi3 acicular structure. Microhardness and wear resistance of the intermetallic coating was significantly higher in comparison with cp-Ti. The maximum microhardness of clads was 480 HV. A wear rate of clads was 10 times lower than that of cp-Ti.
- Open Access
- 20 April 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 124 (1) , 012136
The Structure and Properties of Cast Iron Alloyed with Copper
Cast iron with 3 wt. % Cu was prepared by induction melting and casting in sand molds. The structure of the samples was studied using light microscopy (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The addition of Cu promoted formation of pearlite and slightly decreased the volume fraction of graphite. No Cu inclusions were found by LM and SEM. The nanoprecipitations of ε-Cu in lamellar pearlite were observed by TEM. The properties of the Cu-alloyed cast iron were compared with the properties of cast iron not alloyed with Cu. The hardness of cast iron after alloying with Cu increased and the friction coefficient decreased in comparison with the reference sample.
- 20 April 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 124 (1) , 012136
Open AccessThe Structure and Properties of Cast Iron Alloyed with Copper
Cast iron with 3 wt. % Cu was prepared by induction melting and casting in sand molds. The structure of the samples was studied using light microscopy (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The addition of Cu promoted formation of pearlite and slightly decreased the volume fraction of graphite. No Cu inclusions were found by LM and SEM. The nanoprecipitations of ε-Cu in lamellar pearlite were observed by TEM. The properties of the Cu-alloyed cast iron were compared with the properties of cast iron not alloyed with Cu. The hardness of cast iron after alloying with Cu increased and the friction coefficient decreased in comparison with the reference sample.