Michihisa Fukumoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Michihisa Fukumoto has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Hiroki Takahashi
Graduate School of Engineering Science, Akita University, 1-1 Tegata-gakuen-machi, Akita 010-8502, Japan
11 shared publications - Dawid Kutyła
Faculty of Non-Ferrous Metals, AGH University of Krakow, al. A. Mickiewicza 30, 30-059 Krakow, Poland
8 shared publications - Piotr Żabiński
Faculty of Non-Ferrous Metals, AGH University of Krakow, 30-059 Krakow, Poland
7 shared publications Kano Nakajima
Department of Materials Science, Graduate School of Engineering Science, Akita University, Akita, Japan
4 shared publications- Kano Nakajima
Graduate School of Engineering, Akita University, Akita 010-8502, Japan
4 shared publications - Katarzyna Skibińska
Department of Physical Chemistry and Metallurgy of Non-Ferrous Metals, Faculty of Non-Ferrous Metals, AGH University of Krakow, al. Adama Mickiewicza 30, 30-059 Kraków, Poland
4 shared publications
Latest Publications
- Open Access
Temperature-Controlled Molten-Salt Treatment of Co-Coated Ni Substrates to Form Porous Electrodes for Alkaline Hydrogen and Oxygen Evolution Reactions
In this work, porous coatings were obtained by Co electrodeposition on Ni, followed by Al deposition and anodic dissolution in a NaCl–KCl–AlF3 melt at 750, 825 and 900 °C. The same Co-coated Ni precursor, applied potentials and 3600 s Al-deposition time were used at all temperatures; the recorded anodic durations and transferred charges differed. SEM observations showed a change from a fine sponge-like surface to a coarser porous network. The estimated layer thicknesses were 8–12, 32–55 and 50–65 µm, respectively. The main XRD reflections were consistent with an fcc metallic phase in Co-rich material, with possible overlapping signals from Ni. Weak additional reflections were tentatively associated with Al-containing phases, but their identity was not confirmed. The highest apparent capacitance estimate was obtained at 825 °C. In 1 M NaOH, the lowest HER overpotentials among the treated electrodes were registered for the 900 °C sample: 109 and 494 mV after 2 h at −10 and −100 mA cm−2. For OER, the lowest apparent Tafel slope was obtained at 750 °C, while the lowest end-of-test overpotentials were obtained at 900 °C. Unmodified Ni showed higher anodic currents in part of the polarisation range, so the treatment did not give a general improvement in OER compared with Ni. No post-measurement iR correction was applied. The measured electrodes showed different trends in morphology, apparent capacitance and HER/OER response; statistical significance and between-electrode reproducibility were not established.
Open AccessTemperature-Controlled Molten-Salt Treatment of Co-Coated Ni Substrates to Form Porous Electrodes for Alkaline Hydrogen and Oxygen Evolution Reactions
In this work, porous coatings were obtained by Co electrodeposition on Ni, followed by Al deposition and anodic dissolution in a NaCl–KCl–AlF3 melt at 750, 825 and 900 °C. The same Co-coated Ni precursor, applied potentials and 3600 s Al-deposition time were used at all temperatures; the recorded anodic durations and transferred charges differed. SEM observations showed a change from a fine sponge-like surface to a coarser porous network. The estimated layer thicknesses were 8–12, 32–55 and 50–65 µm, respectively. The main XRD reflections were consistent with an fcc metallic phase in Co-rich material, with possible overlapping signals from Ni. Weak additional reflections were tentatively associated with Al-containing phases, but their identity was not confirmed. The highest apparent capacitance estimate was obtained at 825 °C. In 1 M NaOH, the lowest HER overpotentials among the treated electrodes were registered for the 900 °C sample: 109 and 494 mV after 2 h at −10 and −100 mA cm−2. For OER, the lowest apparent Tafel slope was obtained at 750 °C, while the lowest end-of-test overpotentials were obtained at 900 °C. Unmodified Ni showed higher anodic currents in part of the polarisation range, so the treatment did not give a general improvement in OER compared with Ni. No post-measurement iR correction was applied. The measured electrodes showed different trends in morphology, apparent capacitance and HER/OER response; statistical significance and between-electrode reproducibility were not established.
- Open Access
Synthesis and Evaluation of Layered Ni–Co and Ni–Co–Ni Electrodes Modified by Molten–Salt Al Deposition/Dissolution Technique for Electrochemical Applications
Porous bilayer Ni–Co and sandwiched Ni–Co–Ni electrodes were fabricated by combining aqueous electrodeposition with high-temperature molten-salt Al deposition and subsequent electrochemical dissolution in NaCl–KCl–AlF3 melt at 750 °C. The study aimed to determine how the initial layer architecture controls phase evolution, porous structure formation, and hydrogen evolution performance in alkaline media. SEM/EDS and XRD analyses showed that the two electrode designs followed different reaction pathways during molten-salt treatment. In the Ni–Co system, Al reacted predominantly with Co, leading mainly to Co–Al intermetallic formation and, after dissolution, to a highly open coral-like porous network. In contrast, the Ni–Co–Ni architecture promoted mainly Ni–Al phase formation and produced a more compact porous surface with a Ni-rich outer layer. Despite these morphological differences, both layered porous electrodes outperformed untreated Ni and porous Ni in 1 M NaOH. At −0.6 V vs. RHE, porous Ni–Co and NiCo–Ni reached current densities of −162 and −141 mA·cm−2, respectively, compared with −87 mA·cm for porous Ni and −45 mA·cm for flat Ni. The Ni–Co–Ni sandwiched electrode showed the most favourable HER kinetics and benchmark performance, with the lowest Tafel slope (111 mV·dec) and the lowest potentials at −10 and −100 mA·cm (−0.132 and −0.556 V, respectively). These results demonstrate that the electrocatalytic response of molten-salt-derived porous Ni-based electrodes is governed not only by porosity development but also by the spatial arrangement of metallic layers prior to Al infiltration and dealloying.
Open AccessSynthesis and Evaluation of Layered Ni–Co and Ni–Co–Ni Electrodes Modified by Molten–Salt Al Deposition/Dissolution Technique for Electrochemical Applications
Porous bilayer Ni–Co and sandwiched Ni–Co–Ni electrodes were fabricated by combining aqueous electrodeposition with high-temperature molten-salt Al deposition and subsequent electrochemical dissolution in NaCl–KCl–AlF3 melt at 750 °C. The study aimed to determine how the initial layer architecture controls phase evolution, porous structure formation, and hydrogen evolution performance in alkaline media. SEM/EDS and XRD analyses showed that the two electrode designs followed different reaction pathways during molten-salt treatment. In the Ni–Co system, Al reacted predominantly with Co, leading mainly to Co–Al intermetallic formation and, after dissolution, to a highly open coral-like porous network. In contrast, the Ni–Co–Ni architecture promoted mainly Ni–Al phase formation and produced a more compact porous surface with a Ni-rich outer layer. Despite these morphological differences, both layered porous electrodes outperformed untreated Ni and porous Ni in 1 M NaOH. At −0.6 V vs. RHE, porous Ni–Co and NiCo–Ni reached current densities of −162 and −141 mA·cm−2, respectively, compared with −87 mA·cm for porous Ni and −45 mA·cm for flat Ni. The Ni–Co–Ni sandwiched electrode showed the most favourable HER kinetics and benchmark performance, with the lowest Tafel slope (111 mV·dec) and the lowest potentials at −10 and −100 mA·cm (−0.132 and −0.556 V, respectively). These results demonstrate that the electrocatalytic response of molten-salt-derived porous Ni-based electrodes is governed not only by porosity development but also by the spatial arrangement of metallic layers prior to Al infiltration and dealloying.
- 13 May 2026
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 103 (3) , 47
Predicting the Corrosion Resistance of Fe–Cr Alloys in Ammonia Environments Using Gaussian Process Regression
- 13 May 2026
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 103 (3) , 47
Predicting the Corrosion Resistance of Fe–Cr Alloys in Ammonia Environments Using Gaussian Process Regression
- Open Access
Electrochemical Urea Oxidation on Porous Ni and Ni–M (M = Ir, Pt) Electrodes Obtained via Molten-Salt Treatment Technique
Porous Ni, Ni–Ir, and Ni–Pt electrodes were prepared on Ni substrates by molten-salt Al co-deposition followed by dealloying. SEM/EDS and XRD confirmed a Raney-type porous network with Ir or Pt present across the layer. A urea oxidation reaction (UOR) was tested in 1 M NaOH + 0.33 M urea by cyclic voltammetry and chronoamperometry at +0.40 V vs. SCE (60 min). Smooth Ni showed near-zero current. Porous Ni resulted in ~11 mA cm−2 initially and ~9 mA cm−2 after 60 min. Porous Ni–Ir started at ~7 mA cm−2 and fell to ~2 mA cm−2 within 5 min, indicating fast deactivation, likely due to Ir-oxide formation that suppresses the Ni2+/Ni3+ redox couple. Porous Ni–Pt remained at ~11 mA cm−2 over 60 min, consistent with a stable Ni–Pt effect in which Pt aids urea adsorption/activation while Ni provides the redox path for oxidation. Overall, Pt improves UOR performance, whereas Ir lowers it under these conditions.
Open AccessElectrochemical Urea Oxidation on Porous Ni and Ni–M (M = Ir, Pt) Electrodes Obtained via Molten-Salt Treatment Technique
Porous Ni, Ni–Ir, and Ni–Pt electrodes were prepared on Ni substrates by molten-salt Al co-deposition followed by dealloying. SEM/EDS and XRD confirmed a Raney-type porous network with Ir or Pt present across the layer. A urea oxidation reaction (UOR) was tested in 1 M NaOH + 0.33 M urea by cyclic voltammetry and chronoamperometry at +0.40 V vs. SCE (60 min). Smooth Ni showed near-zero current. Porous Ni resulted in ~11 mA cm−2 initially and ~9 mA cm−2 after 60 min. Porous Ni–Ir started at ~7 mA cm−2 and fell to ~2 mA cm−2 within 5 min, indicating fast deactivation, likely due to Ir-oxide formation that suppresses the Ni2+/Ni3+ redox couple. Porous Ni–Pt remained at ~11 mA cm−2 over 60 min, consistent with a stable Ni–Pt effect in which Pt aids urea adsorption/activation while Ni provides the redox path for oxidation. Overall, Pt improves UOR performance, whereas Ir lowers it under these conditions.
- Open Access
- 15 September 2024
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 110 (12) , 932-940
In-situ Observation of the Environmental Resistance of Pure Iron Using Hydrogen and Oxygen Sensors in the Environment Simulating Hydrogen Combustion
The environmental resistance of pure iron was evaluated with oxygen and hydrogen sensor installed after the oxidation furnace. The amount of introduced oxygen was precisely controlled by oxygen pump-sensor at the front stage of the oxidation furnace and the reaction with hydrogen was analyzed. As a result, when oxygen was supplied, a reaction between hydrogen and oxygen occurred, but when sufficient oxygen was not supplied, a hydrogen-vapor environment was created and oxidation was not accelerated. However, when the amount of supplied oxygen was excessive, the environment became oxygen-steam environment and the oxidation was accelerated. At that time, it was clarified that the oxidation by oxygen was dominant under the oxygen-water vapor environment, and the mass gain increased. In addition, the border of the region dominated by oxygen oxidation and that by steam oxidation was clarified by precisely controlling the amount of supplied oxygen by the oxygen pump sensor.
- 15 September 2024
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 110 (12) , 932-940
Open AccessIn-situ Observation of the Environmental Resistance of Pure Iron Using Hydrogen and Oxygen Sensors in the Environment Simulating Hydrogen Combustion
The environmental resistance of pure iron was evaluated with oxygen and hydrogen sensor installed after the oxidation furnace. The amount of introduced oxygen was precisely controlled by oxygen pump-sensor at the front stage of the oxidation furnace and the reaction with hydrogen was analyzed. As a result, when oxygen was supplied, a reaction between hydrogen and oxygen occurred, but when sufficient oxygen was not supplied, a hydrogen-vapor environment was created and oxidation was not accelerated. However, when the amount of supplied oxygen was excessive, the environment became oxygen-steam environment and the oxidation was accelerated. At that time, it was clarified that the oxidation by oxygen was dominant under the oxygen-water vapor environment, and the mass gain increased. In addition, the border of the region dominated by oxygen oxidation and that by steam oxidation was clarified by precisely controlling the amount of supplied oxygen by the oxygen pump sensor.
- 13 September 2024
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 101 (6) , 1265-1276
Evaluation of Environmental Behavior of Pure Iron in an Ammonia Atmosphere by Using a Hydrogen and an Oxygen Sensor
- 13 September 2024
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 101 (6) , 1265-1276
Evaluation of Environmental Behavior of Pure Iron in an Ammonia Atmosphere by Using a Hydrogen and an Oxygen Sensor
- Open Access
Catalytic Activity Evaluation of the Molten Salt-Modified Novel Ni Electrodes for Urea Electrooxidation in Alkaline Solutions
The presented paper characterized the molten salt-modified Ni electrode with excellent catalytic activity towards alkaline urea electrooxidation reaction. The electrodes were modified by electrodeposition of Al from molten salt electrolytes containing NaCl-KCl-AlF3 at a temperature of 750 °C and applied potential of −1.9 V. The porous surface was obtained by anodic polarization with a potential of −0.4 V until the anodic current was equal to 0 mAcm−2. The prepared deposits’ structure, surface morphology, and composition were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). Anodic polarization was applied to assess the electrocatalytic activity and elucidate the urea electrooxidation mechanism in 1 M KOH + 0.33 M urea solution. The nanocrystalline structure, fine grain size, and microcracks on the surface of the studied electrodes contributed to their notably high electrochemically active surface area (ECSA). The cyclic voltammetry in the non-Faradaic regions of the samples shows that molten salt modification can increase the double layer capacitance of bare Ni plates by around ten times, from 0.29 mFcm−2 to 2.16 mFcm−2. Polarization of the electrodes in urea-containing KOH solution with potential of +1.52 V shows a significant difference in catalytic performance. For the bare nickel sample, the registered current density from the urea electrooxidation reaction was around +1 mAcm−2, and for the molten salt-modified one, it was +38 mAcm−2, which indicates the fact that the molten salt surface treatment can be a promising tool in tailoring the electrochemical properties of materials.
Open AccessCatalytic Activity Evaluation of the Molten Salt-Modified Novel Ni Electrodes for Urea Electrooxidation in Alkaline Solutions
The presented paper characterized the molten salt-modified Ni electrode with excellent catalytic activity towards alkaline urea electrooxidation reaction. The electrodes were modified by electrodeposition of Al from molten salt electrolytes containing NaCl-KCl-AlF3 at a temperature of 750 °C and applied potential of −1.9 V. The porous surface was obtained by anodic polarization with a potential of −0.4 V until the anodic current was equal to 0 mAcm−2. The prepared deposits’ structure, surface morphology, and composition were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). Anodic polarization was applied to assess the electrocatalytic activity and elucidate the urea electrooxidation mechanism in 1 M KOH + 0.33 M urea solution. The nanocrystalline structure, fine grain size, and microcracks on the surface of the studied electrodes contributed to their notably high electrochemically active surface area (ECSA). The cyclic voltammetry in the non-Faradaic regions of the samples shows that molten salt modification can increase the double layer capacitance of bare Ni plates by around ten times, from 0.29 mFcm−2 to 2.16 mFcm−2. Polarization of the electrodes in urea-containing KOH solution with potential of +1.52 V shows a significant difference in catalytic performance. For the bare nickel sample, the registered current density from the urea electrooxidation reaction was around +1 mAcm−2, and for the molten salt-modified one, it was +38 mAcm−2, which indicates the fact that the molten salt surface treatment can be a promising tool in tailoring the electrochemical properties of materials.
- Open Access
Catalytic Activity Evaluation of Molten Salt-Treated Stainless Steel Electrodes for Hydrogen Evolution Reaction in Alkaline Medium
The goal of this research is to fabricate a novel type of highly active porous electrode material, based on stainless steel and dedicated to water electrolyzers. The main novelty of the presented work is the innovative application of the molten salts treatment, which allows the design of a highly developed porous structure, which characterizes significantly higher catalytic activity than untreated steel substrates. The equimolar mixture of NaCl and KCl with 3.5 mol% AlF3 was used as the molten salt. The surface modification procedure includes the deposition of an Al layer with application at the potential of −1.8 V and following dissolution at −0.9 V, to create a porous alloy surface. The cathodic polarization measurements of the prepared porous stainless steel electrodes were measured in a 10 mass% KOH solution. Moreover, the amount of hydrogen generated during constant voltage electrolysis with a hydrogen sensor in situ was also measured. The porous stainless steel alloy showed higher current density at lower potentials in the cathodic polarization compared to untreated stainless steel. The cathodic polarization measurements in alkaline solution showed that the porous 304 stainless steel alloy is an excellent cathode material.
Open AccessCatalytic Activity Evaluation of Molten Salt-Treated Stainless Steel Electrodes for Hydrogen Evolution Reaction in Alkaline Medium
The goal of this research is to fabricate a novel type of highly active porous electrode material, based on stainless steel and dedicated to water electrolyzers. The main novelty of the presented work is the innovative application of the molten salts treatment, which allows the design of a highly developed porous structure, which characterizes significantly higher catalytic activity than untreated steel substrates. The equimolar mixture of NaCl and KCl with 3.5 mol% AlF3 was used as the molten salt. The surface modification procedure includes the deposition of an Al layer with application at the potential of −1.8 V and following dissolution at −0.9 V, to create a porous alloy surface. The cathodic polarization measurements of the prepared porous stainless steel electrodes were measured in a 10 mass% KOH solution. Moreover, the amount of hydrogen generated during constant voltage electrolysis with a hydrogen sensor in situ was also measured. The porous stainless steel alloy showed higher current density at lower potentials in the cathodic polarization compared to untreated stainless steel. The cathodic polarization measurements in alkaline solution showed that the porous 304 stainless steel alloy is an excellent cathode material.